DW Windsor Series User manual

Unpack the lantern and frog and fix them together as shown below.
Sheet 1 of 2
• DISCONNECT ELECTRICAL SUPPLY BEFORE INSTALLATION OR SERVICING.
• THIS PRODUCT MUST BE EARTHED.
• THIS PRODUCT IS DESIGNED TO OPERATE OUTDOORS. IF REQUIRED TO BE
USED INDOORS PLEASE CONSULT DW WINDSOR.
Tools not supplied.
Fig. 2
*Maximum weight of lantern including spigot fixing
Fig. 1 - Windsor lantern
Fig. 2 - Tools required for Windsor / Lancaster installation. Not supplied.
• Luminaire to be positioned so that prolonged staring into the
luminaire at short distances is not expected.
• Do not stare at operating light source.
• Personnel to wear Protective Safety Glasses compliant with EN166 1F/ EN169 - 5
when commissioning or maintaining this luminaire.
Due to continuous product development the details within this document
are subject to change at any time, please contact us for the most up-to-date
information or visit: www.dwwindsor.com
DW Windsor
Pindar Road, Hoddesdon, Hertfordshire, EN11 ODX
T: [phone] | E: [e-mail]
dwwindsor.com Issue 03 - February 2018
Fig. 1
Fig. 3
Fig. 4
Fig. 3 - Attaching frog base.
Fig. 4 - Attaching cast base.
Step 1
Unpack lantern and base. Pass cable through centre of base. Locate base on
studs. Tighten nuts onto studs to the correct torque. Refit black balls finger
tight. Wire cable into terminal block:
Important Wiring Code
L = Live, N = Neutral, E = Earth
This lantern must be earthed.
Tools required:
10mm Spanner2
Pozi or Slotted
Screwdriver
3
Tools required:
10mm Spanner2
Pozi or Slotted
Screwdriver
3
The Windsor Range
Traditional Lanterns
Street and Avenue sizes
Installation Instructions
IMPORTANT
NOTE!
Product Details
The Windsor range is supplied with lantern and “spigot fixing” separated.
Tools Required
Recommended Torque
10mm Spanner2 Pozi or Slotted
Screwdriver
3
5mm Allen Key1
Base Attachment
Dimensions (mm) Max. Weight (kg)* Windage m²
A B C ØC D
Street 833 440 76 76 188 10.3 0.28
Avenue 745 390 76 76 119 8.3 0.22
Base Nut Torque (Nm) Column Mounting Torque (Nm)
Street 30 16
Avenue 30 16
230VAC 50Hz
IP65 IK08

Sheet 2 of 2
LEDs contained within this luminaire shall only be replaced
by the manufacturer, their service agent or similar qualified
person.
DW Windsor
Pindar Road, Hoddesdon, Hertfordshire, EN11 ODX
T: [phone] | E: [e-mail]
dwwindsor.com Issue 03 - February 2018
Step 3
Ensure lantern is vertical. Tighten set screws to the correct torque.
Lamping, Relamping, and Maintenance Access
Unfasten the two slide catches holding the lid in position, hinge up the lid and support
it with the lid stay.
For lamped lanterns, ensure correct lamp is used (refer to the information on the
control gear ballast if in doubt). Loosen the screws on the lampholder bracket and
lift clear. Fit the lamp into the lampholder. For ES and GES lamps, ensure they are
firmly screwed home. The lampholders are fitted with an anti-vibration device. Refit
lampholder and lid.
Pozi or Slotted
Screwdriver
3
Tools required: Tools required:
5mm Allen Key1
See sheet 1 for wiring code.
Ensure lid stay is secure before relamping.
The Windsor Range
Traditional Lanterns
Street and Avenue sizes
NOTE!
Windsor installation steps
Step 2
Wire cable into terminal block and carefully fit lantern onto column.