DW SitePro SLR202GR Quick guide

Toll Free: [phone] www.SitePro.us.com
Operating / Safety Instructions
Consignes de fonctionnement / sécurité
Instrucciones de funcionamiento y seguridad
model SLR202GR
IMPORTANTE:
Leer antes de usar
IMPORTANT
Lire avant usage
IMPORTANT:
Read Before Using

2
GENERAL SAFETY RULES
Working safely with this instrument is possible only when the operating and safety infor-
mation are read completely and the instructions contained therein are strictly followed.
The use of controls, adjustments, or the performance of procedures other than those
specied herein may result in hazardous radiation exposure.
DO NOT stare into the laser beams.
DO NOT direct the laser beam at other persons.
DO NOT disassemble the instrument or attempt to perform any internal servicing. Laser
class is indicated on the instrument. Repair and servicing of this laser are to be per-
formed only by SitePro or authorized service centers.
• When attaching the instrument to a tripod, make sure the instrument is securely
xed. The tripod leg clamps should be securely fastened. If not securely fastened
or tightened, the main unit could fall off or the tripod could fall over.
• The laser should not be stored or used in extreme temperature or during rapid
temperature change. The laser may not function properly if used out of the ambi-
ent temperature range.
• Store inside the carry case and place in a dry area not subject to vibration, dust
or high moisture. If the storage temperature and ambient temperature for usage
vary signicantly, leave the laser in its case until it can adjust to the ambient
temperature.
• The laser should be transported or carried carefully to avoid impact or vibration.
• The laser should be stored in the carry case and packed with cushioning material.
Always handle the laser with care.
Dave White’s Site Pro, LLC
www.sitepro.us.com Made in China
Laser radiation. Do not stare into the beam or view directly with optical instruments.
Class 2M lasers product. Complies with 21 CFR 1040.10 & 1040.11 except for
deviations persuant to Laser Notice 50, June 6, 2007
Radiación laser. No mire hacia el rayo. No mirar con instrumentos ópticos. Producto
láser de Clase 2M. Cumple con las normas 21 CFR 1040.10 y 1040.11, excepto
por las desviaciones conforme al Aviso para láseres 50, 6 de junio de 2007
Rayonnement laser. Ne pas regarder le rayon. Ne pas regarder avec instruments .
Produit laser de Classe 2M. Conforme à 21 CFR 1040.10 et 1040.11, sauf pour
les écarts suivant l’Avis laser 50, 24/6/2007
IEC 60825-1:2007-03
≤ 1 mW @ 630 - 670 nm
2M

www.SitePro.us.com 3
1
2
7
6
5
3
4
9
8
23
Fig. A

4
1. Light House
2. Rotating Head
3. Glass Enclosed
4. Heavy-Duty Handle
5. Control Keypad
6. Charging Port
7. Instrument Base and Battery Pack
8. Laser Plumb Beam
9. Laser Down Plumb Beam
SLR202GR
Leveling Accuracy 1/8-in at 100-ft (3mm at 30m)
Range with Detector (Diameter) 1600-ft (500m)
Interior Range (Diameter) 320-ft (98m)
Leveling Type (Degrees) Electronic (±5º)
Beam Rating Class 3R, 635nm
Grade/Slope Capability Dual (±10.00%), Dial-in
Variable Rotation Speed Settings 0, 60, 120, 300, and 600 RPM
Scanning Angle Settings 10°, 45°, 90°, 180°
Remote Control Operating Distance up to 65-ft (20 m)
Power Supply NiMh Rechargeable Approx. 20hr of continuous use.
or Four (4) C cell alkline batteries
Water/Dust Protection IP54
Dimension: 6.3 x 6.3 x 7.3-in (160mm x 160mm x 185mm)
Weight: 6.6 lb (3.0 kg) with batteries
TECHNICAL DATA
FEATURES (Fig. A)

www.SitePro.us.com 5
CONTROL KEYPAD ICONS
Power ON/OFF: Allow laser instrument to self-leveling. Use also to activate the
plumb up and plumb down beam.
Manual/Automatic: While instrument is ON, press and hold once, to activate
Manual Mode. The laser instrument is no longer in self-leveling mode and can be
positioned at any angle/slope.
Variable Rotation Speed Mode: This mode will increase or decrease the speed
of the rotating laser. Four (4) preset speeds can be obtained: 0 RPM, 60 RPM,
120 RPM, 300 RPM, and 600 RPM.
Smart H.I. Alert System: When enabled alerts user when laser has been dis-
turbed. When the LED is blinking slowly, the laser is in H.I Alert mode. When the
light is blinking quickly, the laser level will not level as it has been disturbed and
needs reset.
Scanning Mode: Creates a shorter, brighter laser “chalk line” that can be used for
leveling or alignment. Five (5) preset angles of scanning are available- 0°, 10°,
45°, 90°, and180°.
Clock-Wise and Counter-Clock-Wise Beam Positioning: When laser is in Scanning
Mode, laser beam can be repositioned in clock-wise or counter-clock-wise rota-
tion. When laser in Slope/Grade Mode, these buttons are used to adjust the
value of the X% and Y% slope/grade.
Slope/Grade Mode: When laser is in Slope/Grade Mode, laser beam can be
adjusted in both the X and Y axis for single or dual slope applications.
X- and Y- Axis Positioning: When laser is in Slope/Grade Mode, the button is used
to adjust either the X% or Y% grade value.
RPM
Scanning
Mode
Beam
Positioning
Manual
Mode
Variable
Speed
Smart
H.I.
Single
Slope
Dual
Slope
Power
WINDY
RPM
Scanning
Mode
Beam
Positioning
Manual
Mode
Variable
Speed
Smart
H.I.
Single
Slope
Dual
Slope
Power
WINDY
RPM
Scanning
Mode
Beam
Positioning
Manual
Mode
Variable
Speed
Smart
H.I.
Single
Slope
Dual
Slope
Power
WINDY
RPM
Scanning
Mode
Beam
Positioning
Manual
Mode
Variable
Speed
Smart
H.I.
Single
Slope
Dual
Slope
Power
WINDY
RPM
Scanning
Mode
Beam
Positioning
Manual
Mode
Variable
Speed
Smart
H.I.
Single
Slope
Dual
Slope
Power
WINDY
RPM
Scanning
Mode
Beam
Positioning
Manual
Mode
Variable
Speed
Smart
H.I.
Single
Slope
Dual
Slope
Power
WINDY
RPM
Scanning
Mode
Beam
Positioning
Manual
Mode
Variable
Speed
Smart
H.I.
Single
Slope
Dual
Slope
Power
WINDY
RPM
Scanning
Mode
Beam
Positioning
Manual
Mode
Variable
Speed
Smart
H.I.
Single
Slope
Dual
Slope
Power
WINDY
RPM
Scanning
Mode
Beam
Positioning
Manual
Mode
Variable
Speed
Smart
H.I.
Single
Slope
Dual
Slope
Power
WINDY

6
PREPARATIONS
Battery Installment
Rechargeable and alkaline battery packs are suitable for use to power your instrument.
To install/remove batteries:
1. Un-screw the bolt at the bottom of instrument base. Remove the battery pack.
2. Use either alkaline battery or Ni-Mh battery pack. When inserting alkaline batties,
pay attention to the correct polarity according to the representation on the inside
of the battery compartment. Always replace all batteries at the same time. Only
use batteries from one brand and with the identical capacity.
3. When installing the battery pack onto base, be certain that electrode connection
align properly. Secure by tighten the bolt onto the bottom of instrument base.
Remove the batteries from the tool when not using it for extended periods. When storing
for extended periods, the batteries can corrode and discharge themselves.
Charging Rechargeable NiMh Battery Pack
Insert the charger into the outlet and the charging port of the instrument or the battery
pack. Turn on the power. The charger LED will display 1 of 3 modes:
Red ashing light Battery NOT Charging Check connections
Red light Battery Charging Take up to 8 hrs to fully charge
Green light Battery Fully Charged Ready for Use
Note:
• When using the standard rechargeable batteries of the instrument, recharging
takes up to 8 hours (4 x 5000 mAh Ni-Mh batteries).
• Power required for the charger: Frequency: 50-60HZ; Voltage: 85-265V.
• Instrument can be used while charging batteries
• Brand-new rechargeable batteries or rechargeable batteries unused for long
period need to be recharged and discharged three times to attain full capacity.

www.SitePro.us.com 7
OPERATIONS
Set-up
Place the laser instrument on a at, level survace such as a tripod Setup the instrument
in an area where it can not be obstructed and is set at a convenient height.
IMPORTANT. Be sure the surface is level with +/- 5° of the laser self-leveling range.
Power
Press the
RPM
Scanning
Mode
Beam
Positioning
Manual
Mode
Variable
Speed
Smart
H.I.
Single
Slope
Dual
Slope
Power
WINDY
Power ON/OFF keypad and allow the laser instrument to self-level. If the
power indicator LED blinks, the voltage of the batteries is low and batteries need to be
replaced or recharged.
Leveling
The laser instrument can stand alone on a level, sturdy surface or preferably secured to
a 5⁄8” -11 tripod. Press the Power keypad once, and allow time for the instrument to
self-level.
After self-leveling, the laser instrument will begin operating in Rotation Mode at the
speed of 600 RPM. If the instrument is placed improperly, or the slope of instrument
exceeds the range of +/-5°, the Power indicator LED and the laser beam will blink at the
same time.
Note: The instrument will shut down automatically if the unit exceeds the self-leveling
system range for more then 5 minutes.
RPM
Scanning
Mode
Beam
Positioning
Manual
Mode
Variable
Speed
Smart
H.I.
Single
Slope
Dual
Slope
Power
WINDY
Variable Rotation Speed
The Variable Rotation Speed Mode keypad will give you the option of increasing or de-
creasing the speed of the rotating laser. Repeatedly pressing the keypad will adjust the
speed from 600, 300, 120, 60, and 0 RPM.

8
RPM
Scanning
Mode
Beam
Positioning
Manual
Mode
Variable
Speed
Smart
H.I.
Single
Slope
Dual
Slope
Power
WINDY
Scanning or Sweeping
The Scanning Mode creates a shorter, brighter laser “chalk line” that can be used for
leveling or plumbing. This feature can also be used to keep the instrument from interfer-
ing with other lasers and detectors on site. Pressing the Scanning Mode keypad, will
lengthen or shorten the scan area of the laser beam.
While in Scanning Mode, the position of the scanning area can be adjusted. Press the
RPM
Scanning
Mode
Beam
Positioning
Manual
Mode
Variable
Speed
Smart
H.I.
Single
Slope
Dual
Slope
Power
WINDY
Clock-Wise or
RPM
Scanning
Mode
Beam
Positioning
Manual
Mode
Variable
Speed
Smart
H.I.
Single
Slope
Dual
Slope
Power
WINDY
Counter-Clock-Wise Beam Positioning keypads.
Slope/Grade Mode
Single Slope - Adjusting the Slope of Y-Axis
For single slope applications, the slope or grade can be as much as a positive or negative
10.00%, and set in reference to the Y axis of the instrument. Position Y1-beam in the
direction of the slope required.
When the instrument is set upright for horizontal rotation, the slope of the Y-axis can be
adjusted. Press the Grade Mode button
RPM
Scanning
Mode
Beam
Positioning
Manual
Mode
Variable
Speed
Smart
H.I.
Single
Slope
Dual
Slope
Power
WINDY
, the instrument will enter into the mode of
manual grade adjustment.
Y1
Y2
X1
X2
Y

www.SitePro.us.com 9
First, the X% value on the display will begin to ash. Press the
RPM
Scanning
Mode
Beam
Positioning
Manual
Mode
Variable
Speed
Smart
H.I.
Single
Slope
Dual
Slope
Power
WINDY
button to enter the Y-axis slope/grade menu. The Y% value
on the display will begin to ash.
Press the
RPM
Scanning
Mode
Beam
Positioning
Manual
Mode
Variable
Speed
Smart
H.I.
Single
Slope
Dual
Slope
Power
WINDY
or
RPM
Scanning
Mode
Beam
Positioning
Manual
Mode
Variable
Speed
Smart
H.I.
Single
Slope
Dual
Slope
Power
WINDY
buttons to adjust the Y% grade value. Continue until the required
value is set. The Y-axis slope/grade value can be set between +10.00% and -10.00%.
Once values are set, press the
RPM
Scanning
Mode
Beam
Positioning
Manual
Mode
Variable
Speed
Smart
H.I.
Single
Slope
Dual
Slope
Power
WINDY
button. After a few seconds, the instrument will
process the values and adjust the laser beam to the grade set. The laser beam will begin
to rotate.
If the instrument is disturbed during operation, an audible alarm will sound to indicate
that the instrument has moved. If disturbed, you need to reconrm all references and
benchmarks. If you determine that instrument has not shifted from its original position,
press the
RPM
Scanning
Mode
Beam
Positioning
Manual
Mode
Variable
Speed
Smart
H.I.
Single
Slope
Dual
Slope
Power
WINDY
button to re-start the instrument and return to grade mode.
Dual Slope/Grade - Adjusting the Slope of Both Axis
When the instrument is set upright for horizontal rotation, the slope of the X-axis and
Y-axis can be adjusted by entering the Slope/Grade Mode. Press the Grade Mode button
RPM
Scanning
Mode
Beam
Positioning
Manual
Mode
Variable
Speed
Smart
H.I.
Single
Slope
Dual
Slope
Power
WINDY
, the instrument will enter into the mode of manual grade adjustment.
First, the X% value on the display will begin to ash.
Press the
RPM
Scanning
Mode
Beam
Positioning
Manual
Mode
Variable
Speed
Smart
H.I.
Single
Slope
Dual
Slope
Power
WINDY
or
RPM
Scanning
Mode
Beam
Positioning
Manual
Mode
Variable
Speed
Smart
H.I.
Single
Slope
Dual
Slope
Power
WINDY
buttons to adjust the X% grade value. Continue until the required
value is set. The X-axis slope/grade value can be set between +10.00% and -10.00%.
Press the
RPM
Scanning
Mode
Beam
Positioning
Manual
Mode
Variable
Speed
Smart
H.I.
Single
Slope
Dual
Slope
Power
WINDY
button to enter the Y-axis slope/grade menu.
The Y% value on the display will begin to ash.
Press the
RPM
Scanning
Mode
Beam
Positioning
Manual
Mode
Variable
Speed
Smart
H.I.
Single
Slope
Dual
Slope
Power
WINDY
or
RPM
Scanning
Mode
Beam
Positioning
Manual
Mode
Variable
Speed
Smart
H.I.
Single
Slope
Dual
Slope
Power
WINDY
buttons to adjust the Y% grade value. Continue until the required
value is set. The Y-axis slope/grade value can be set between +10.00% and -10.00%.
Once values are set, press the
RPM
Scanning
Mode
Beam
Positioning
Manual
Mode
Variable
Speed
Smart
H.I.
Single
Slope
Dual
Slope
Power
WINDY
button. After a few seconds, the instrument will
process the values and adjust the laser beam to the grade set. The laser beam will begin
to rotate.

10
Vertical Laydown Positioning
Place the laser instrument in the laydown
position on a at, level surface.
Press the Power ON/OFF
RPM
Scanning
Mode
Beam
Positioning
Manual
Mode
Variable
Speed
Smart
H.I.
Single
Slope
Dual
Slope
Power
WINDY
button. Allow
the instrument to self-level.
ACCURACY CHECK
Follow these instructions for checking axis accuracy.
Horizontal-Surface Checking
Place the laser instrument at the point of 165 ft (50m) from a wall or set a scale plate,
and then adjust the level of the base approximately to aim the Y1 towards the wall (or
scale plate).
SLR202GR
4XC1.5V
DaveWhite’sSitePro,LLC MadeinChina
Laserradiation.Avoiddirecteyeexposure.Class3Rlasersproduct. Complies with
21CFR1040.10&1040.11exceptfordeviationspersuantto Laser Notice 50, June
6,2007
Radiaciónlaser.Nomirehaciaelrayo.Productoláser deClase3R.Cumpleconlas
normas21CFR1040.10y1040.11,exceptoporlasdesviaciones conforme al Aviso
paraláseres50,6dejuniode2007
Rayonnementlaser.Nepasregarderlerayon.Produitlaser de Classe 3R. Conforme
à21CFR1040.10et1040.11,saufpourlesécarts suivant l’Avis laser 50,
24/6/2007
3R
z
BA
SLR202GR 4XC1.5V DaveWhite’sSitePro,LLCMadeinChina
Laserradiation.Avoiddirecteyeexposure.Class3Rlasersproduct.Complieswith 21CFR1040.10&1040.11exceptfordeviationspersuanttoLaserNotice 50, June6,2007 Radiaciónlaser.Nomirehaciaelrayo.ProductoláserdeClase 3R. Cumple con las normas21CFR1040.10y1040.11,exceptoporlasdesviacionesconformeal Avisoparaláseres50,6dejuniode2007 Rayonnementlaser.Nepasregarderlerayon.ProduitlaserdeClasse3R. Conforme à21CFR1040.10et1040.11,saufpourlesécartssuivantl’Avis laser 50, 24/6/2007
3R
Approx. 100 ft
(30m)
BA
1.5 ft
(0.5m)
1.5 ft
(0.5m)
Approx. 100 ft
(30m)
1.5 ft
(0.5m)
1.5 ft
(0.5m)
z
BA
Approx. 100 ft
(30m)
1.5 ft
(0.5m)
1.5 ft
(0.5m)
165 ft
(50m)
Y+ H1
Approx. 100 ft
(30m)
BA
y
1.5 ft
(0.5m)
1.5 ft
(0.5m)
H1
165 ft
(50m)
-Y
H2
y1
y1
y1
y1
y2
z
BA
Approx. 100 ft
(30m)
1.5 ft
(0.5m)
1.5 ft
(0.5m)
SLR202GR 4XC1.5V DaveWhite’sSitePro,LLCMadeinChina
Laserradiation.Avoiddirecteyeexposure.Class3Rlasersproduct.Complieswith 21CFR1040.10&1040.11exceptfordeviationspersuanttoLaserNotice 50, June6,2007 Radiaciónlaser.Nomirehaciaelrayo.ProductoláserdeClase 3R. Cumple con las normas21CFR1040.10y1040.11,exceptoporlasdesviacionesconformeal Avisoparaláseres50,6dejuniode2007 Rayonnementlaser.Nepasregarderlerayon.ProduitlaserdeClasse3R.Conforme à21CFR1040.10et1040.11,saufpourlesécartssuivantl’Avis laser 50, 24/6/2007
3R

www.SitePro.us.com 11
Allow the laser instrument to self level and begin rotating. Mark the beam position on the
wall or scale plate as H1.
Loosen the screw of the tripod, and then turn the laser 180°. Allow the unit to level and
rotate, mark the beam position on the wall or scale plate as H2.
The distance between H1 and H2 should be less than 3/8-in (8 mm).
Repeat the same process to check your Y-axis beam. Again, the distance between H1
and H2 should be less than 3/8-in (8 mm).
If the difference in either axis is more than 3/8-in (8 mm), the laser should be sent to
your authorized dealer for service and calibration.
Horizontal-line checking
First lay down the instrument. Mount
the instrument on tripod between wall
(or target) Aand B. Tripod should be
placed approx. 1.5ft (0.5m) from wall
(or target) A. Power the instrument on.
After leveling, direct the laser beam
onto the close wall A. Mark the center
point y1of the laser beam on the wall.
SLR202GR
4XC1.5V
DaveWhite’sSitePro,LLC MadeinChina
Laserradiation.Avoiddirecteyeexposure.Class3Rlasersproduct. Complies with
21CFR1040.10&1040.11exceptfordeviationspersuantto Laser Notice 50, June
6,2007
Radiaciónlaser.Nomirehaciaelrayo.Productoláser deClase3R.Cumpleconlas
normas21CFR1040.10y1040.11,exceptoporlasdesviaciones conforme al Aviso
paraláseres50,6dejuniode2007
Rayonnementlaser.Nepasregarderlerayon.Produitlaser de Classe 3R. Conforme
à21CFR1040.10et1040.11,saufpourlesécarts suivant l’Avis laser 50,
24/6/2007
3R
z
BA
SLR202GR 4XC1.5V DaveWhite’sSitePro,LLCMadeinChina
Laserradiation.Avoiddirecteyeexposure.Class3Rlasersproduct.Complieswith 21CFR1040.10&1040.11exceptfordeviationspersuanttoLaserNotice 50, June6,2007 Radiaciónlaser.Nomirehaciaelrayo.ProductoláserdeClase 3R. Cumple con las normas21CFR1040.10y1040.11,exceptoporlasdesviacionesconformeal Avisoparaláseres50,6dejuniode2007 Rayonnementlaser.Nepasregarderlerayon.ProduitlaserdeClasse3R. Conforme à21CFR1040.10et1040.11,saufpourlesécartssuivantl’Avis laser 50,
24/6/2007
3R
Approx. 100 ft
(30m)
BA
1.5 ft
(0.5m)
1.5 ft
(0.5m)
Approx. 100 ft
(30m)
1.5 ft
(0.5m)
1.5 ft
(0.5m)
z
BA
Approx. 100 ft
(30m)
1.5 ft
(0.5m)
1.5 ft
(0.5m)
165 ft
(50m)
Y+ H1
Approx. 100 ft
(30m)
BA
y
1.5 ft
(0.5m)
1.5 ft
(0.5m)
H1
165 ft
(50m)
-Y
H2
y1
y1
y1
y1
y2
z
BA
Approx. 100 ft
(30m)
1.5 ft
(0.5m)
1.5 ft
(0.5m)
SLR202GR 4XC1.5V DaveWhite’sSitePro,LLCMadeinChina
Laserradiation.Avoiddirecteyeexposure.Class3Rlasersproduct.Complieswith 21CFR1040.10&1040.11exceptfordeviationspersuanttoLaserNotice 50, June6,2007 Radiaciónlaser.Nomirehaciaelrayo.ProductoláserdeClase 3R. Cumple con las normas21CFR1040.10y1040.11,exceptoporlasdesviacionesconformeal Avisoparaláseres50,6dejuniode2007 Rayonnementlaser.Nepasregarderlerayon.ProduitlaserdeClasse3R.Conforme à21CFR1040.10et1040.11,saufpourlesécartssuivantl’Avis laser 50, 24/6/2007
3R
SLR202GR
4XC1.5V
DaveWhite’sSitePro,LLC MadeinChina
Laserradiation.Avoiddirecteyeexposure.Class3R lasers product. Complies with
21CFR1040.10&1040.11exceptfordeviations persuant to Laser Notice 50, June
6,2007
Radiaciónlaser.Nomirehaciaelrayo.Producto láser deClase3R.Cumpleconlas
normas21CFR1040.10y1040.11,exceptopor las desviaciones conforme al Aviso
paraláseres50,6dejuniode2007
Rayonnementlaser.Nepasregarderlerayon.Produit laser de Classe 3R. Conforme
à21CFR1040.10et1040.11,saufpour les écarts suivant l’Avis laser 50,
24/6/2007
3R
z
BA
SLR202GR 4XC1.5V DaveWhite’sSitePro,LLCMadein China
Laserradiation.Avoiddirecteyeexposure.Class3Rlasersproduct.Complies with 21CFR1040.10&1040.11exceptfordeviationspersuanttoLaser Notice 50, June6,2007 Radiaciónlaser.Nomirehaciaelrayo.Productoláser de Clase 3R. Cumple con las normas21CFR1040.10y1040.11,exceptoporlasdesviacionesconforme al Avisoparaláseres50,6dejuniode2007 Rayonnementlaser.Nepasregarderlerayon.Produitlaserde Classe 3R. Conforme à21CFR1040.10et1040.11,saufpourlesécartssuivant l’Avis laser 50,
24/6/2007
3R
Approx. 100 ft
(30m)
BA
1.5 ft
(0.5m)
1.5 ft
(0.5m)
Approx. 100 ft
(30m)
1.5 ft
(0.5m)
1.5 ft
(0.5m)
z
BA
Approx. 100 ft
(30m)
1.5 ft
(0.5m)
1.5 ft
(0.5m)
165 ft
(50m)
Y+ H1
Approx. 100 ft
(30m)
BA
y
1.5 ft
(0.5m)
1.5 ft
(0.5m)
H1
165 ft
(50m)
-Y
H2
y1
y1
y1
y1
y2
z
BA
Approx. 100 ft
(30m)
1.5 ft
(0.5m)
1.5 ft
(0.5m)
SLR202GR 4XC1.5V DaveWhite’sSitePro,LLCMadein China
Laserradiation.Avoiddirecteyeexposure.Class3Rlasersproduct.Complies with 21CFR1040.10&1040.11exceptfordeviationspersuanttoLaser Notice 50, June6,2007 Radiaciónlaser.Nomirehaciaelrayo.Productoláser de Clase 3R. Cumple con las normas21CFR1040.10y1040.11,exceptoporlasdesviacionesconforme al Avisoparaláseres50,6dejuniode2007 Rayonnementlaser.Nepasregarderlerayon.ProduitlaserdeClasse 3R. Conforme à21CFR1040.10et1040.11,saufpourlesécartssuivant l’Avis laser 50, 24/6/2007
3R

12
Rotate the instrument horizontally
180° (without changing the height).
After laser instrument levels, direct
the laser beam onto Wall B. Mark
the center point zof the laser beam
on the opposite wall B.
Without turning the instrument.
Position laser instrument close to
wall Bby moving the tripod. Switch
on the instrument and let it level.
After leveling, align the height of the
instrument by using tripod (or by
underlayment), so that the center
point of the laser beam is projected
exactly at the point z.
Rotate the instrument 180° without
changing the height. Allow it to level,
and mark the center point y2 of the
laser beam on wall A. Be sure that
point y2 is as vertical aligned as
possible to point y1.
Measure the distance beween
points y1 and y2. The deviation of the
plumb up beam should be less than
0.16-in (4mm).
SLR202GR
4XC1.5V
DaveWhite’sSitePro,LLC MadeinChina
Laserradiation.Avoiddirecteyeexposure.Class3R lasers product. Complies with
21CFR1040.10&1040.11exceptfordeviations persuant to Laser Notice 50, June
6,2007
Radiaciónlaser.Nomirehaciaelrayo.Producto láser deClase3R.Cumpleconlas
normas21CFR1040.10y1040.11,exceptopor las desviaciones conforme al Aviso
paraláseres50,6dejuniode2007
Rayonnementlaser.Nepasregarderlerayon.Produit laser de Classe 3R. Conforme
à21CFR1040.10et1040.11,saufpour les écarts suivant l’Avis laser 50,
24/6/2007
3R
z
BA
SLR202GR 4XC1.5V DaveWhite’sSitePro,LLCMadein China
Laserradiation.Avoiddirecteyeexposure.Class3Rlasersproduct.Complies with 21CFR1040.10&1040.11exceptfordeviationspersuanttoLaser Notice 50, June6,2007 Radiaciónlaser.Nomirehaciaelrayo.Productoláser de Clase 3R. Cumple con las normas21CFR1040.10y1040.11,exceptoporlasdesviacionesconforme al Avisoparaláseres50,6dejuniode2007 Rayonnementlaser.Nepasregarderlerayon.Produitlaserde Classe 3R. Conforme à21CFR1040.10et1040.11,saufpourlesécartssuivant l’Avis laser 50,
24/6/2007
3R
Approx. 100 ft
(30m)
BA
1.5 ft
(0.5m)
1.5 ft
(0.5m)
Approx. 100 ft
(30m)
1.5 ft
(0.5m)
1.5 ft
(0.5m)
z
BA
Approx. 100 ft
(30m)
1.5 ft
(0.5m)
1.5 ft
(0.5m)
165 ft
(50m)
Y+ H1
Approx. 100 ft
(30m)
BA
y
1.5 ft
(0.5m)
1.5 ft
(0.5m)
H1
165 ft
(50m)
-Y
H2
y1
y1
y1
y1
y2
z
BA
Approx. 100 ft
(30m)
1.5 ft
(0.5m)
1.5 ft
(0.5m)
SLR202GR 4XC1.5V DaveWhite’sSitePro,LLCMadein China
Laserradiation.Avoiddirecteyeexposure.Class3Rlasersproduct.Complies with 21CFR1040.10&1040.11exceptfordeviationspersuanttoLaser Notice 50, June6,2007 Radiaciónlaser.Nomirehaciaelrayo.Productoláser de Clase 3R. Cumple con las normas21CFR1040.10y1040.11,exceptoporlasdesviacionesconforme al Avisoparaláseres50,6dejuniode2007 Rayonnementlaser.Nepasregarderlerayon.ProduitlaserdeClasse 3R. Conforme à21CFR1040.10et1040.11,saufpourlesécartssuivant l’Avis laser 50,
24/6/2007
3R

REMOTE CONTROL
The remote control can be used up to a
maximum of 65 feet (20 m) away from the
instrument. Setup the instrument and power
on (remote does not power on instrument).
The remote control communicates with the
laser instrument in real-time. The remote
must be pointed towards the instrument for
proper operation.
The remote controls the laser the same as
the keypads on the instrument.
1. LCD Real-Time Display
2. Power Button (powers remote, not
laser intrument)
3. Counter Clock-wise Rotation Button
4. Clock-wise Rotation Button
5. Sweep Mode Button
6. X/Y Grade Adjustment Button
7. Rotation Speed Button
8. Grade/Slope Mode Button
Requires 2 ‘AA’ Alkaline batteries.
DETECTOR
Use the detector with the laser instrument when working outdoors or in illuminated work
areas. The detector will pick up a rotating laser beam when it crosses the electronic
sensor window.
3
1
5
24
6
7
8

14
MAINTENANCE
Store and transport the tool only in the
supplied protective case.
Keep the laser instrument clean.
Do not immerse the tool into water or
other uids. Wipe off debris using a moist
and soft cloth. Regularly clean the glass
surfaces of the laser tool for nger marks
and debris.
If the tool should fail, repair should be car-
ried out by an authorized SitePro Service
Center.
In all correspondence and spare parts
orders, please always include the product
model and serial number.
If repairs are needed, send in the laser
instrument in its protective case.
ENVIRONMENT PROTECTION
Recycle raw materials & bat-
teries instead of disposing of
waste. The unit, accessories,
packaging & used batteries
should be sorted for environ-
mentally friendly recycling in
accordance with the latest
regulations.
The detector has 3 control buttons:
ON/OFF Button
Audio Button with 3 settings:
OFF – LOW – HIGH
Sensitivity Button
This will either give a narrow or a
broader range of detection. When the
detector is too high a slower beep will
be emitted, when too low, a fast beep
will be emitted, when same
level as beam a continuous pitch will sound- at this point the centre of the detector is at
the same alignment as the beam.
To get accurate results use the spirit bubble to keep the detector level. The detector is
powered by a standard 9v battery.

www.SitePro.us.com 15
WARRANTY
Limited Warranty Program
SitePro warrants the SLR200 Series Rotary Lasers to the original purchaser for a period
of two (2) years from date of purchase against any defects in material or workmanship.
This warranty does not cover part failure due to normal wear or tool abuse. For more
details of warranty coverage and warranty repair information, call [phone]. This
warranty does not apply to accessories items or damage caused where repairs have
been made or attempted by person other than SitePro or authorized service center.
This warranty gives you specic legal rights and you may have other rights which vary in
certain states or provinces.
This Limited Warranty does not apply to accessory items such as tripods, rods, poles,
prisms, hand levels, eld supplies, instrument accessories and other related items.
These items receive a 90 day limited warranty.
To make a claim under this Limited Warranty, you must return the tool, transportation
prepaid, along with any relevant paperwork (RGA number, if you have obtained one, proof
of purchase, contact information, and any request for new accessories, etc.) to our
Service Department or an Authorized Service Center.
SitePro/Service Department, 7619 S 1150 E, Otterbein, IN 47970
IMPLIED WARRANTIES ARE EXPRESSLY LIMITED IN DURATION TO ONE YEAR FROM
DATE OF PURCHASE.
IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES (INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF PROFITS) ARIS-
ING FROM THE SALE OR USE OF THIS PRODUCT. SOME STATES IN THE U.S., AND
SOME CANADIAN PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT
APPLY TO YOU.
SOME STATES IN THE U.S. AND SOME CANADIAN PROVINCES DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, OR THE EXCLUSION
OR LIMITATION OF SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THESE
LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU
SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM
STATE/PROVINCE TO STATE/PROVINCE.

© Dave White’s SitePro, LLC
Otterbein, IN
www.sitepro.us.com
UM-27SLR202 r.1 5/15 Printed in China