Dwyer Instruments UHH-BTG Installation and operating instructions
Model UHH-BTG Wireless Mobile Gateway
pecifications - Installation and Operating Instructions
Bulletin TE-UHH-BTG
PECIFICATION
Wireless Protocol: Conforms to Bluetooth SIG, Inc. low energy wireless
technology.
Wireless Distances: 50´ (15 m) or greater.
Response Time: 1 s.
Temperature Limits:
Ambient: 5 to 125°F (-15 to 51°C);
Battery Charging: 32 to 113°F (0 to 45°C).
Power Requirements: 3.7 V YT562447 lithium ion battery, installed functional,
user replaceable.
Weight: 2.5 oz (70.87 g).
Agency Approvals: CE with CE approved charger, RoHS, FCC.
The Model UHH-BTG Wireless Mobile Wireless Gateway transforms the
wireless signal from any Dwyer Instruments, Inc. universal handheld probe or
module into a Bluetooth SIG, Inc, Wireless Technology. Using this gateway, any
iOS®Firmware version 5.X or later or Android® Firmware version 3.X or later
smartphone or tablet can become the base instrument for measuring or logging.
Once the gateway is paired with a phone or tablet, our obile eter™ app or any
other Dwyer Instruments, Inc. approved apps can detect available probes or
modules. Wireless gateways can detect probes or modules that are 50 feet away
or even greater distances depending on the environment. The wireless signal from
the gateway to the mobile device adds at least another 25 feet of sensing distance.
odel UHH-BTG is compact in size and clips on to most standard belts. The
rechargeable battery can be charged using the same mini-USB cable and charger
as the probes or modules. LED lights indicate the battery status and whether the
gateway is communicating properly.
2-13/16
[71.50]
2-7/16
[61.98]
1-3/16
[29.86] 1-17/32
[39.15]
LED tatus
Paired or pairable to
phone or tablet
Communications to
mobile device or probes
Charging or powering off
Low battery
iOS®is a registered trademark of Cisco Systems, Inc.
Android®is a registered trademark of Google, Inc.
Belt Clip
Bi-Color LED
Power Button
U B Charger
Connector
Figure 1
Blue LED
Slow blink
Rapid blink
Off
Off
Red LED
Off
Off
Solid
Slow Blink
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) This device may not cause harmful interference. and (2) this device must accept
any interference received, including interference that may cause undesired
operation.
Cet appareil est conforme à des règlements d'Industrie Canada exempts de licence
standard RSS (s). Son fonctionnement est soumis aux deux conditions suivantes:
(1) Ce dispositif ne doit pas causer d'interférences nuisibles, et (2) cet appareil doit
accepter toute interférence reçue, y compris les interférences pouvant entraîner un
fonctionnement indésirable.
This Class B digital apparatus complies with Canadian ICE -003.
Cet appareil numériqué de la classe B est conformé à la norme NMB-003 du
Canada.
NOTICE
Shop for Data Logging products online at: www.DataLoggerStore.com 1.888.610.7664
Pairing to Phone or Tablet
The obile eter™ app will need to be downloaded and installed to the mobile
device from Google play or Apple iTunes store. In order to pair the odel UHH-BTG
Wireless obile Gateway to your phone or tablet, you must first turn on the
gateway by pushing the power button on the top of the gateway (see Figure 1 to
locate the power button). Next, either open the obile eter™ app or go directly to
the bluetooth menu (see Figure 2) in the settings menu on your phone or tablet. The
bridge is automatically discoverable once it is turned on. Select the device named
PROBEBRIDGE followed by the serial number of your gateway. If prompted for a
pass code, type in 0000. Once the gateway is paired to the phone, the blue LED
on the gateway will flash when communications are transmitted between the phone
and the gateway.
Pairing Probes or Modules to Gateway
The wireless probes and modules automatically become discoverable to the
gateway when they are turned on if they are not already connected to another
gateway or odel UHH base unit. You must be in the obile eter™ or other
Dwyer Instruments, Inc. approved app to see which probes are paired. The blue
LED on the gateway and the green LED on the probe will flash rapidly when there
is communication between the probe and the gateway.
Mobile Meter™ App Operation
Upon opening the obile eter™ app, you will see “Get Started” if the Wireless
obile Gateway is paired to the device.
During your first time using the app, you will not have any probes paired yet. It will
prompt you to go to the probe set up menu to find available probes. Turn on your
probes or modules at this time to make them discoverable before hitting the button
on the phone.
There is a refresh button in the set up menu if you don’t see the desired probe or
module in the list. Select the desired probes or modules by touching the box on the
right side of the screen. You can always go back to the probe selection screen by
pressing set up in the upper right hand corner of the obile eter™ app. The past
paired probes and modules will be stored in this list as well. Probes or modules that
are currently unavailable will be in grey, but they can still be selected to display
when they become active. Pressing the arrow next to the Dwyer logo at the top of
the screen will return you to the active probes list.
This active probe list will give the probe names and the measurement data for all
of the selected probes. Additional information such as low battery warnings of the
probes and the communication status is available in this screen. Touching the
wrench will take you to the measurement preference menu for that probe.
Figure 3
Touch to get
started
Figure 4
Touch to setup
probes
Figure 5
Touch to select
probe
Touch to refresh
Touch to go back
to previous menu
It is recommended that only four probes be selected due to
bandwidth limitations between the phone and the gateway.
NOTICE
Figure 6
Touch to access
parameters
Connection
status
Figure 2
Touch to go to
bluetooth menu
Shop for Data Logging products online at: www.DataLoggerStore.com 1.888.610.7664
In the Preference enu, you can select which parameter will be displayed larger on
the screen, the function of the parameter, engineering units, and logging method.
Pressing the arrow next to the Dwyer logo will return to the active probe list.
Any of the probes can be made full screen by touching the desired probe. In this
view, you can scroll through the active probes by swiping the screen to the left or
right. Logging can be initiated in this screen by either pressing the button on the
probe or by pressing the Log button at the bottom of the screen. If the logging is set
to manual, each button push will save one measurement. If the logging is set to
duration, it will log continuously for the set duration.
In order to end a log file, press the Save Log button on the bottom of the screen.
You can either view the log file, share the log file, or close the log file. In order to
view the log file, touch Open Log. If you desire to share the log file, you can select
to share the file via wireless communication to another device, email the file directly
from the phone, or share it via Wi-Fi to another device on the same network.
Otherwise, touching OK will close the file for later access.
The measurements are normally displayed as a digital meter. If desired, the
measurements can be shown as an analog gauge by touching the gauge icon at
the top of the screen.
Figure 9
Figure 10
Touch to toggle
between meter
and gauge view
Only one probe can be logged at a time and you can not switch
to another probe until you save and close the log.
NOTICE
Figure 7
Logging method
Touch to change
units
Figure 8
Touch to end and
save log file
Touch to
start log
Shop for Data Logging products online at: www.DataLoggerStore.com 1.888.610.7664
MAINTENANCE/REPAIR
Upon final installation of the odel UHH-BTG, no routine maintenance is required.
The odel UHH-BTG is not field serviceable and should be returned if repair is
needed. Field repair should not be attempted and may void warranty.
WARRANTY/RETURN
Refer to “Terms and Conditions of Sale” in our catalog and on our website. Contact
customer service to receive a Return Goods Authorization number before shipping
the product back for repair. Be sure to include a brief description of the problem
plus any additional application notes.
Shop for Data Logging products online at: www.DataLoggerStore.com 1.888.610.7664
