Dwyer Instruments THI2-10 User manual

Model THI2-10 Digital Remote Sensing Thermohygrometer
Specifications - Installation and Operating Instructions
Bulletin TE-THI2-10
S ECIFICATIONS
Service: Humidity and temperature detection in air.
Range:
Relative humidity measurement range: 0 to 100%;
Temperature range: 14 to 140°F (-10 to 60°C);
Dew point temperature range: -100 to 139.8°F (-73.4 to 59.9°C);
Wet bulb temperature range: 7.88 to 139.8°F (-13.4 to 59.9°C).
Accuracy:
Relative humidity accuracy: ±3% from 10 to 90% (at calibration
temperature); ±5% for others;
Temperature accuracy: ±1°F (±.6°C).
Display: Dual LCD display for temperature and humidity.
Temperature Limits:
Ambient: 32 to 122°F (0 to 50 C);
Storage: 68 to 140°F (-20 to 60°C).
Resolution:
Temperature resolution: 0.1°C/°F;
Humidity resolution: 0.1% RH.
ower Requirements: 4 AAA batteries included.
Weight: 5.3 oz (150 g).
Agency Approval: CE.
The THI2-10 Digital Remote Sensing Thermohygrometer accurately takes
humidity, temperature, dew point and wet bulb temperatures inside of ducts and hard
to reach areas. English and metric engineering units as well as the type of
measurement displayed can be easily selected using the push buttons. The push
buttons also allow the user to freeze the current reading or retrieve the minimum and
maximum readings. A large backlit LCD digital dual display allows the user to see both
the temperature and humidity simultaneously and a low battery indicator shows the
user when to change batteries. For hands free operation, the thermohygrometer can
be mounted on a tripod. All units include 4 AAA batteries and a hard carrying case for
safe
O ERATING INSTRUCTIONS
LCD & Keypad:
ower ON/OFF:
1. Press the button to turn on the meter and enter normal mode. Unit will
automatically turn off after 20 minutes without any buttons being pressed.
2. Press the same button to turn off the meter in any mode.
Back Light:
Press the key to turn on the back light of the LCD for 10 seconds.
Unit Selection:
In normal mode, press to switch the units between °C and °F.
Hold Reading:
1. Only in normal mode, press to freeze the current reading.
2. Press again to return to normal display.
8-5/8
[219.00]
2-13/32
[61.07]
1-1/8
[28.77]
6-45/64
[170.31]
1-19/64
[33.05]
2-49/64
[70.43]
Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176
TestEquipmentDepot.com

Air/Dew oint/Wet Bulb:
Press and hold to switch between air temperature, dew point (DP) and wet bulb
temperature (WBT) in normal mode.
Current/Min./Max Values:
1. Press to cycle the display between the current value, minimum value, and
maximum value.
2. Press and hold more than one second to reset the minimum and maximum
values.
Disable Automatic Shut Off:
While the meter is off, press + to turn on the meter for continuous use.
Calibration:
1. To turn off the meter, plug the meter probe into a 32.8% salt bottle and hold the +
key for more than one second to turn on the meter and enter calibration mode.
2. You will see 3x.x% is flashing on the LCD.
After 30 minutes, the “3x.x%” will stop flashing, meaning that the calibration is finished
and saved. You can also manually end and save the calibration by holding the key
for more than one second.
3. ove the meter probe into a 75.3% salt bottle and hold “ N/ X/RST” for more than
one second to enter the 7x.x% calibration. “7x.x% will flash on the LCD”.
4. “7x.x%” will stop flashing after 30 min. The calibration has been completed. You can
manually end and save the calibration by holding the key for more than one
second.
Troubleshooting:
MAINTENANCE/RE AIR
Upon final installation of the odel THI2-10, no routine maintenance is required. The
odel THI2-10 is not field serviceable and should be returned if repair is needed.
Field repair should not be attempted and may void warranty.
WARRANTY/RETURN
Refer to “Terms and Conditions of Sales” in our catalog and on our website. Contact
customer service to receive a Return Goods Authorization number before shipping the
product back for repair. Be sure to include a brief description of the problem plus any
additional application notes.
©Copyright 2011 Dwyer Instruments, Inc. Printed in U.S.A. 8/11 FR# R6-443937-00
When the meter is on, pluging the probe into the calibration
solution will also result in “E 33” or “E 34” in max. and min. mode.
NOTICE
a) Auto power off is automatically disabled during calibration
procedure.
b) In order to get a high accuracy, you must do the calibration at 23 ± 2°C (69.8 ±
3.6°F) and in a steady airflow room.
c) Once the calibration is finished, if the value differs from 7x.x% or 3x.x% for more than
.3%, it means the calibration has failed (see troubleshooting 3.)
NOTICE
Symptom
ower On But No Display
Display Disappeared
Calibration Failure
Display Message E11
Display Message E33
Display Message E34
Action
ake sure the time of pressing the key is more
than 100 ms.
Check that the batteries are in place, good contact
and correct polarity.
Replace new batteries and try again.
ove the batteries away for one minute and install
again.
Check whether the low battery indicator is on before
the display disappeared. If yes, replace with new
batteries.
Turn on the meter by pressing the + key
to disable auto power off function for long time usage.
Check whether the low battery indicator is on before
the display disappeared. If yes, replace with new
batteries.
ake sure that the sealing is good when plugging the
meter probe into the salt bottle.
ake sure the free air temperature is within 23 ±2°C
(73.4 ±35.6°F) and the airflow is stable.
RH calibration error, re-calibrate.
Circuit error in RH measurement, return the meter to
its dealer.
Circuit error in temperature measurement channel,
return the meter to its dealer.
Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176
TestEquipmentDepot.com