dynarex 10328 User manual

Reorder No. 10328
R181121
Bariatric Tub
Transfer
Bench
LIMITED LIFETIME
WARRANTY
Your Dynarex product is warrantied to be free of defects
in materials and workmanship for the lifetime of the
product for the original purchaser. This item was built to
exacting standards and carefully inspected prior to
shipment. This Limited Lifetime Warranty is an
expression of our confidence in the materials and
workmanship of our products and our assurance to the
consumer of years of dependable service.
The Warranty shall not apply under the following
conditions: Problems arising from normal wear; Problems
arising from failure to adhere to the product instructions;
Problems arising from misuse, negligence, accident or
improper operation, maintenance or storage; Problems
arising from modifications or unauthorized repairs, parts
or attachments; Products where the serial number has
been removed or defaced; Problems with non-durable
components, such as rubber accessories, casters, and
grips, which are subject to normal wear and need
periodic replacement. Dynarex shall not be liable for any
consequential or incidental damages whatsoever.
Dynarex shall repair or replace defective products at its
option. The foregoing warranty is exclusive and in lieu of
other express warranties, if any, including the implied
warranties of merchantability and fitness of a particular
purpose. The remedy for any violation of the implied
warranty shall be limited to repair or replacement of the
defective product pursuant to the terms contained herein.
SYMBOL GLOSSARY
For an explanation of symbols
used in Dynarex packaging, visit
dynarex.com/symbols.php
Manufactured for: Dynarex Corporation
10 Glenshaw Street • Orangeburg, NY 10962
USA • www.dynarex.com
Made in China

ASSEMBLY INSTRUCTIONS
Weight Capacity: 500 lb. (227 kg)
Figure 1
Figure 3 Figure 4
Figure 2
1. Inspect all parts for shipping damage before assembly. If
there is shipping damage – DO NOT USE. Contact
dealer/carrier for further instructions.
2. Make certain that the height adjusting snap buttons fully
protrude through the same respective hole of each leg
extension. This will ensure that the leg extensions are
securely locked in position and an even height is achieved.
3. Ensure ALL screws, nuts and/or bolts are tightened.
4. Check the rubber tips on the leg extensions for rips, wear
or if they are missing. Immediately replace any or all if any
of these imperfections exist.
5. All four leg extensions with rubber tips MUST touch the
floor simultaneously at all times.
6. When using the bench to transfer a patient into a tub, the
legs with the suction cups should be placed inside the
bathtub.
7. DO NOT stand on chair.
NOTE: To maintain the beauty of the original finish, clean
with mild soap and rinse with warm water. Wipe bath seat
dry after each use.
ADJUSTING LEG HEIGHT
1. Before use, adjust height of each leg to your specific
needs, making sure all legs are at the same height. When
desired height is reached, lock legs into place by aligning
buttons into proper holes.
NOTE: Make sure all legs are set to the same height.
2. To be sure legs are locked into place, push down or pull up
on legs.
WARNING
1. Lay the chair base with the seat surface facing down and
the leg sockets facing up.
2. Insert the legs with the suction cup on the side of the chair
with the arm rest bracket. Depress the brass push-pin and
insert the leg into the socket until the brass push-pin
“snaps” through the hole.
3. Insert the legs with the small rubber tip on the other side of
the chair. Depress the brass push-pin and insert the leg
into the socket until the brass push-pin “snaps” through the
hole. (Figure 1)
4. Turn the transfer bench upright.
5. Insert the armrest into the side of the bench with the
suction cup legs. Make sure the arm arches outwards.
Ensure that the brass push-pin “snaps” through the hole.
(Figure 2)
6. Insert the back rest support poles to the chair back. Ensure
that the brass push-pin “snaps” through the hole. (Figure 3)
7. Depress the brass push-pin and insert the back rest
support pole into the support bracket. The support poles
should go through two sets of brackets on each side. The
back rest can be placed on either side of the chair. Ensure
brass push-pin “snap” through the holes in the support
bracket. (Figure 4)