Dynascan ISC Box User manual

ISC BOX QUICK START GUIDE
Technology, Inc.

TV TunerRS-232 of ISC RS-232 of DVI Board*
Fans Power Connection
- The ISC Box allows you to connect various external devices to
be used as video sources (i.e. DVD Player, Video Camera, etc.)
- The connection interface of this device is divided as follows:
1 - A / V Connection Panel (located on the front)
2 - System Panel (located at the back)
ABOUT THE ISC BOX
- Depending on the Model, the ISC Box
could be internal or external
- For Models DS0706 / 0616C / 0808C, the ISC is Internal
- The input power is already connected through the display’s
main switch; whenever this is turned ON, so will the ISC
- For Model DS1508 / 2012, the ISC is External
- Using included power connect to a 110V outlet
- See power connector on the right for reference
GETTING POWER FOR THE UNIT
* RS-232 of DVI Board is used for the Monitor System Software
(included)

AVAILABLE VIDEO INPUTS
a - Video-In 1 and 2: composite (RCA) connection
b - SVideo-In 1 and 2: standard S-Video connection
c - Y.Cb.Cr / Y.Pb.Pr: component video connection
d - DVI / VGA: computer or HD-DVI connection
e - TV tuner (on back side of ISC - System Panel)
AVAILABLE AUDIO INPUTS
f - Audio-In 1 and 2: RCA audio connection
g - Component Audio-In 1 and 2: RCA audio connection
h - PC Audio In: mini jack connection from PC audio
or memory card players
SETTING-UP EXTERNAL DEVICES
- Steps:
1 - Access the Connection Panel*
2 - Connect the video cable(s) of your External Device**
to the Connection Panel
eg. memory card player’s S-Video cable, PC’s VGA cable
3 - Connect the audio cable(s) of your External Device
to the Connection Panel
eg. R / L (red, white) audio cables from memory card player
4 - Ensure proper power connection (if needed)
on your External Device
* Refer to your unit’s manual for location of connection panel
Connection Panel (front of ISC)
External Device
(Typical DVD player connection shown as an example)
d
a b c dfh g
** Examples: DVD, Flash Player, Live Camera Feed, and etc...
e. TV Tuner
power

ISC REMOTE CONTROL Power ON/OFF
(save Settings)
Main Menu
ON/OFF
Sound:
Volume Down
Arrow: Left
Arrow: Up
Sound:
Volume up
Arrow: Right
Switch
two sources
Enter: to setup
or go back
GENERAL ACCESS TO THE MENU
- Use the ISC remote for the following steps:
1 - Press MENU button to enter or exit the menu window
2 - Use the arrow buttons to navigate through the menu
3 - Press ENTER button to highlight your selection
(selection will turn into RED letters)
4 - Once highlighted, use LEFT / RIGHT arrows to
change your selection
5 - Press MENU again to exit
MENU ICONS
- From left to right:
1 - IMAGE menu
2 - AUDIO menu
3 - COLOR menu
4 - DISPLAY menu
5 - OSD menu
6 - MISC menu
7 - TV Settings menu
Active
Audio Source

- Press MENU button to enter window menu
- Scroll over to the DISPLAY menu
- Scroll down to either MAIN SOURCE or SUB-SOURCE
- Press ENTER to highlight the source you want to change
(selection will turn into RED letters)
- Once highlighted, use LEFT / RIGHT arrows to
change your source from Video 1 to Video 2 to SVideo, etc
SELECTING VIDEO INPUT SOURCE
FULL mode
CUSTOMIZING THE DISPLAY
WPOP mode POP mode PBP mode PIP mode
Standard picture-in-
picture using TV tuner
CUSTOMIZING THE DISPLAY CON’T
TWO inputs, MAIN & SUB Sources :
TWO different images in separate screens
ONE input as SUB-Source :
Image will expand, showing a wide screen in full wrap
ONE input as MAIN-Source :
Image will clone, showing TWO of the same screens

- Once your inputs have been set as desired,
you can save them as your default inputs by pressing POWER off
- You can turn the ISC back on with new default settings
SAVING SETTINGS
- To select Active Audio Source, press the WINDOW button on the ISC remote
NOTE: Audio-In 1 and 2 are shared between SVideo input and Composite Video input
PC Audio input is shared between VGA and DVI video inputs
SELECTING AUDIO SOURCE
- Here you can adjust image brightness and contrast
- Also, you can change the volume and change the RGB settings of the display
1 - Press MENU to open the setup menu
2 - Press UP or DOWN to move to your desired selection
3 - Press ENTER button to highlight your selection
(selection will turn into RED letters)
IMAGE AND AUDIO MENU ADJUSTMENTS
4 - Once highlighted, use LEFT / RIGHT arrows
to change your selection
5 - Press ENTER to go back to setup menu selections
6 - Press MENU to exit
N O T E :

VIDEO INPUT SOURCE
- To change the video input source without
accessing the menu, use the following shortcut keys
VIDEO button : press repeatedly to circle through
Video1  Video2  Svideo1  Svideo2 
COMP button : press to switch to and from component
Y.Cb.Cr.  Y.Pb.Pr. 
PC button : press to switch to and from
VGA  DVI 
APPENDIX - SHORTCUT KEYS ON THE ISC REMOTE CONTROL
PICTURE MODE
- To change the picture mode without
accessing the menu, use the following shortcut key
POP or PIP buttons : change from one mode to the other
AUDIO INPUT SOURCE
- To change the audio input source without
accessing the menu, use the following shortcut key
WINDOW button : switch active audio source between
MAIN source and SUB source
* If you DO NOT hear a sound:
- ensure proper connection of audio cables
- increase the volume using volume knob on
the front of ISC
- turn volume up with remote
APPENDIX - SHORTCUT KEYS ON THE ISC REMOTE CONTROL CON’T

DYNASCAN CONTACT INFORMATION
Taiwan
66 Hwa-Ya First Road, Hwa-Ya Technical Park,
Kuei-Shan Hsiang, Taoyuan Hsien, Taiwan
Tel: [phone]
Fax: [phone]
[email protected]
Japan
5F, Keihin Tatemono Building, 3-16-10, Shin-Yokohama,
Kohoku-Ku, Yokohama, Kanagawa, Japan
Tel: [phone]
Fax: [phone]
[email protected]
United States of America:
7 Chrysler, Irvine,
California 92618, USA
Tel: [phone]
Fax: [phone]
[email protected]
China
3F, Building 40, Number 333,
Qin Jiang Road, Shanghai, China
Tel: [phone]
Fax: [phone]

DynaScan Technology, Inc.
7 Chrysler, Irvine, CA 92618, USA
T. 949.421.0348 / F. 949.421.0353
E. [email protected]
www.dynascanusa.com