1" 3" 1" A
(76.2)
(25.4) (25.4)
2 1/4"
(57)
B
(25.4) (76.2) (25.4)
1-15/16" B
(49.2)
2-1/4"
(57)
3"1" 1" A
STANDARD INSTALLATION
CLOSER MOUNTED ON DOOR ON PULL SIDE
This drawing shown is LEFT HAND DOOR,
For RIGHT HAND DOOR should be install in symmetry
2 Holes for self
drilling/tapping screws or
14-20 Machine Screws.
4 Holes for self
drilling/tapping screws or
14-20 Machine Screws.
OPENING
TO 100°
*TO 130°
"A" "B"
7-516"
(185)
11-78"
(301)
6-14"
(159)
10-13 16"
(275)
PRELOAD TO
90°
COVER
SCREW
LATCH SPEED
SCREW
MAIN SPEED
SCREW
BACKCHECK
SCREW
FOREARM
SCREW
ROD
ARM
SCREW
MAIN ARM
Page 2 Page 3
TOP JAMB INSTALLATION
CLOSER MOUNTED TOP JAMB ON PUSH SIDE OF DOOR.
This drawing shown is RIGHT HAND DOOR,
For LEFT HAND DOOR should be install in symmetry 4 Holes for self
drilling/tapping screws or
14-20 Machine Screws.
2 Holes for self
drilling/tapping screws or
14-20 Machine Screws.
COVER
SCREW
BACKCHECK
SCREW
MAIN SPEED
SCREW
LATCH SPEED
SCREW
MAIN ARM
ARM
SCREW
ROD
FOREARM
SCREW
PRELOAD TO
90°
11/16"
(17.5)
11/16"
(17.5)
(49.2)
1-15/16"
11/16"
(17.5)
11/16"
(17.5)
Delayed Action
Delayed Action
* Recommended mounting for
meeting ADA compliance
* When door closer is installed and
adjusted to conform to ADA reduced
opening force requirements (5 lbs max.),
it may not have adequate closing force to
reliably close and latch the door.
OPENING
TO 100°
*TO 130°
"A" "B"
7-516"
(185)
11-78"
(301)
6-14"
(159)
10-1316 "
(275)
* Recommended mounting for
meeting ADA compliance
* When door closer is installed and
adjusted to conform to ADA reduced
opening force requirements (5 lbs max.),
it may not have adequate closing force to
reliably close and latch the door.
1. Select degree of opening and use dimensions shown or attached template to
locate 4 holes on door for closer body and 2 holes on frame face for
forearm shoe.
2. Prepare door and frame for fasteners. See "Preparation for Fasteners",
Figure 1, Page 1.
3. Adjust spring power to match door width as indicated by chart on page 1.
4. Mount closer on door as dimensions shown. Tube end toward hinge.If pivots are
used , locate closer and shoe from CENTERLINE OF PIVOT.
(For offset pivots, pl ease increase the marked dimensions by 18")
5. Place main arm on top shaft, 90° to closer body, insert arm screw into top of
shaft and tighten.
6. Attach shoe to frame as dimensions shown. (if more latching power is required,
rotate shoe 180°)
7. Open door and insert rod in forearm.
8. With forearm at right angle to door (90°) ,insert forearm set screw and tighten.
(IF HOLD OPEN ARM IS USED, THE NUT IS ON THE TOP FOR RH DOOR AND
BOTTOM FOR LH DOOR)
REGULATION:
A ' normal ' closing time from 90° open position to door stop position is 4-6 secs,
evenly divided between main swing speed and latch swing speed. Use socket key
(Furnished) to adjust speed. To slow main speed of door, turn regulating screw
nearest shaft clockwise. To slow latch speed, turn regulating screw nearest hinge
clockwise.
BACKCHECK AND DELAYED ACTION
To increase back-check force, turn regulating screw clockwise.
DO NOT USE ABRUPT BACKCHECK OR EXPECT DOOR CLOSER TO ACT AS
A DOOR STOP.
To Increase the Delayed closing time, turn the DA screw clockwise.
COVER
Place insert in Proper cutout, then push cover against door. Tighten both cover
screw securely.
HOLD OPEN ADJUSTMENT (WHEN FRICTION HOLD OPEN ARM IS USED)
Loose adjusting nut, open door to required hold open position and tighten the nut.
Do not permit door to swing beyond hold open setting.
1. Select degree of opening and use dimensions shown or attached template to
locate 4 holes on frame face for closer body and 2 holes on door for
forearm shoe.
2. Prepare door and frame for fasteners. See "Preparation for Fasteners",
Figure 1, Page 1.
3 Adjust spring power to match door width as indicated by chart on page 1.
4. Mount clo ser on frame as dimensions shown. Tube end toward hinge.
If pivots are used , locate closer and shoe from CENTERLINE OF PIVOT.
(For offset pivots, pl ease increase the marked dimensions by 18")
5. Place main arm on top shaft 90° to closer body, insert arm screw into top of
6. Attach shoe to door as shown. (if more latching power is required, rotate shoe 180°)
7. Open door and insert rod in forearm(For reveal 2 58" through 4 1316" use long rod.
For reveals 4 78" to 8" use FOREARM EXTENDER (ROD) -available from
dealer).
8. With forearm at right angle to door (90°) ,insert forearm set screw and tighten.
(IF HOLD OPEN ARM IS USED, THE NUT IS ON THE TOP FOR LH DOOR
RH DOOR)
REGULATION:
A ' normal ' closing time from 90° open position to door stop position is 4-6 secs, evenly di
vided
between main swing speed and latch swing speed. Use socket key (Furnished) to adjust speed.
To slow main speed of door, turn regulating screw nearest shaft clockwise
turn regulating screw nearest hinge clockwise.
BACKCHECK AND DELAYED ACTION
To increase back-check force, turn regulating screw clockwise.
DO NOT USE ABRUPT BACKCHECK OR EXPECT DOOR CLO SER TO ACT AS A DOOR
STOP.
To Increase the Delayed closing time, turn the DA screw clockwise.
COVER
Place insert in Proper cutout, then push cover against door. Tighten both cover screw securely.
HOLD OPEN ADJUSTMENT (WHEN HOLD OPEN ARM IS USED)
Loose adjusting nut, open door to required hold open position and tighten nut.
Do not permit door to swing beyond hold open setting.
Do not scale drawing
Dimensions are in inches (mm)
Do not scale drawing
Dimensions are in inches (mm)
