Dynex DX-WD1201 User manual

ASSEMBLY INSTRUCTIONS
DX-WD1201
Espresso TV Stand for 32" TVs
Safety information and specifications ............2
Tools needed............................................................3
Package contents ...................................................4
Assembly instructions...........................................6

2DX-WD1201
Need help? Call 800-305-2204
Safety information and specifications
Warnings
• Do not let children climb on your stand or play near it. The stand may tip over causing the TV or stand to
injure someone.
• When placing items on the shelves or the top of the stand, load the bottom shelf first and work up to the top
of your stand.
• Do not overload the shelves. They may break.
• Do not move your stand with items on the top or shelves. Your stand may tip over and injure someone. Before
you move your stand, unload starting with the top of your stand and working to the bottom shelf.
• Do not push your stand to move it. With the help of a second person, lift your stand to move it.
CAUTION:
This stand’s work surface is intended only for use
with a product not weighing more than 95 lbs.
(43.09 kg) and accommodates most 32"
flat-panel TVs with dimensions that will permit the TV to sit
evenly on the stand. Using with other products, including
products that weigh more than the maximum weight
allowed, may result in instability, which may cause possible
injury.
Maximum weight: 95 lbs. (43.09 kg)
Maximum screen size: Most 32" flat-panel TVs
Weight capacity (top of stand): 95 lbs. (43 kg)
Weight capacity (top shelf): 35 lbs. (15 kg)
Weight capacity (middle shelf): 25 lbs. (11 kg)
Weight capacity (total lower shelf): 50 lbs (22 kg)
Overall dimensions: (W × H × D)
35.38 x 27.25 × 18 inches (89.86 × 69.21 × 45.72 cm)
Top of stand: (W × D) 35.38 × 18 inches (89.86 × 45.72 cm)
Usable top shelf: (W × H × D)
29 × 6.13 × 15.5 inches (73.66 × 15.57 × 39.37 cm)
Usable left game shelf: (W × H × D)
9.38 × 14.5 × 15.5 inches (23.82 × 36.83 × 39.37 cm)
Usable right middle shelf (in middle position): W × H × D
19.25 × 6.88 × 15.5 inches (48.89 × 17.47 × 39.37 cm)
Usable lower shelf (shelf in middle position): W × H × D
19.25 × 6.88 × 15.5 inches (48.89 × 17.47 × 39.37 cm)
18" (45.72 cm)
35.38" (89.86 cm)
27.25" (69.21 cm)
32.5" (85.55 cm)
15.75" (40 cm)

3
DX-WD1201
Need help? Call 800-305-2204
Tools needed
Hammer
No. 2 Phillips screwdriver
Caution: Do not
use an electric drill
or screwdriver

4DX-WD1201
Need help? Call 800-305-2204
Packagecontents
Package contents: hardware
Make sure you have all the hardware necessary to assemble your new TV stand:
Label Hardware Qty.
M2 17
N2 17
O3
P6
Hidden cam
Cam dowel
Angle
bracket
Metal pin
Label Hardware Qty.
Q4
R13
S1
Rubber
sleeve
Cam cover
Warning
label
Label Hardware Qty.
T2
U6
V24
Black 1-7/8”flat
head screw
Black 9/16” large
head screw
Nail
10 20 30 40 50 60 70 80 90 100mm
1234in

5
DX-WD1201
Need help? Call 800-305-2204
Package contents: parts
Note: All parts except for the back (G) have a lettered sticker to make identifying parts easier.
Letter Description Qty. Letter Description Qty.
ARight end 1 GBack 1
BLeft end 1 HAdjustable shelf 1
CUpright 1 IStop molding 1
DTop 1 JTop skirt 1
EBottom 1 KBottom molding 1
FShelf 1 WEnd molding 2

6DX-WD1201
Need help? Call 800-305-2204
Assembly instr uctions
Step1:
Assemble your stand on a carpeted floor or on the empty carton to avoid scratching your unit or the floor.
A hidden cam (M2) has an arrow. When you insert the hidden cam, make sure that the arrow points toward
the hole in the side of the part you are inserting it into.
Push seventeen hidden cams (M2) into the ends (Aand B), top (D), bottom (E), and shelf (F). Then, insert the
metal end of a cam dowel (N2) into each hidden cam.
You’ll need:
Do not tighten the hidden cams in this step.
Arrow
N2 (17)M2 (17)

7
DX-WD1201
Need help? Call 800-305-2204
Tightening hidden cams:
In the remaining steps, use these illustrations for instructions on tightening hidden cams.
Warning: Risk of damage or injury. Hidden cams must be completely tightened. Hidden cams that are not
completely tightened will loosen, and parts may separate.
You’ll need:
Arrow
Make sure that you turn the
hidden cam a minimum of
190° to a maximum of 210°.
Note the position of the arrow
on the hidden cam.
Arrow
In the illustration below,
the hidden cam has not
been tightened enough.
210°
190°
Phillips screwdriver

8DX-WD1201
Need help? Call 800-305-2204
Step 2:
Fasten the shelf (F) to the ends (Aand B). Use a Phillips screwdriver to tighten four hidden cams (M2). See
“Tightening hidden cams:” on page 7.
Insert two metal pins (P) into the upright (C), then insert the other ends of metal pins (P) into the holes in the
shelf (F).
You’ll need:
Notched edge
Notched
edge
Finished edge
Surface with holes
210° Arrow
190°
P(2)Phillips screwdriver

9
DX-WD1201
Need help? Call 800-305-2204
Step 3:
Slide the bottom molding (K) onto the notched edge of the bottom (E).
Fasten the bottom (E) to the ends (Aand B). Use a Phillips screwdriver to tighten four hidden cams (M2). See
“Tightening hidden cams:” on page 7.
Fasten the bottom (E) to the upright (C). Use a Phillips screwdriver and two black 1-7/8" flat head screws (T).
You’ll need:
fi
Surface
with
hidden
cams
Holes for screws
Arrow
210°
US Patent #5,499,886
190°
T(2)
Phillips screwdriver

10 DX-WD1201
Need help? Call 800-305-2204
Step 4:
Fasten three angle brackets (O) to the stop molding (I). Use a Phillips screwdriver and three black 9/16" large
head screws (U).
Fasten the stop molding (I) to the top (D). Use a Phillips screwdriver to tighten three hidden cams (M2).
See “Tightening hidden cams:” on page 7.
Carefully turn your stand onto its top.
Fasten the ends (Aand B) to the top (D). Use a Phillips screwdriver to tighten six hidden cams (M2).
You’ll need:
Notched edges
Arrow
210°
190°
U(3)Phillips screwdriver O(3)

11
DX-WD1201
Need help? Call 800-305-2204
Step 5:
Slide the end moldings (W) onto the notched edges of the ends (Aand B).
Fasten the top skirt (J) to the angle brackets (O) on the stop molding (I). Use a Phillips screwdriver and three
black 9/16" large head screws (U).
Note: There are no pre-drilled holes in the top skirt (J). The screws will tighten into the groove.
You’ll need:
U(3)
Phillips screwdriver

12 DX-WD1201
Need help? Call 800-305-2204
Step 6:
Carefully turn your stand over onto its front edges. Unfold the back (G) and lay it over your stand.
Make equal margins along the side and bottom edges of the back (G). Push on opposite corners of your stand
if needed to make it “square.”
Fasten the back (G) to your stand using the nails (V).
Note: Make sure that you tap nails into the holes that line up over the upright (C) and shelf (F).
Note: Perforations have been provided for access through the back (G). Carefully cut out the holes needed.
You’ll need:
These holes must line up over the
back edges on the upright (C) and
shelf (F).
Caution: Do not
stand your stand
upright without the
back fastened. Your
stand may collapse.
Do not tap
nails in this
edge
Hammer V(24)

13
DX-WD1201
Need help? Call 800-305-2204
Step 7:
Carefully stand your stand upright.
Push the rubber sleeves (Q) over the remaining metal pins (P). Insert the metal pins (P) into the hole locations
of your choice in the right end (A) and upright (C). Set the adjustable shelf (H) onto the metal pins (P).
Apply the warning label (S) to the top (D). You should be able to read the label when the TV is removed from
your stand. When the TV is in place, it should hide the label. Peel off the backing and apply the label as
shown.
Caution: This is a permanent label intended to last for the life of the product. Once applied, do not try to
remove it. You may damage the finish on the top.
Push a cam cover (R) onto each visible hidden cam (M2).
Clean with your favorite furniture polish or a damp cloth. Wipe dry. Your stand is ready to use.
You’ll need:
Warn
i
ng: Never use t
hi
s
f
urn
i
ture w
i
t
h
a TV
that is too large or too heavy. Severe injury
or death can occur. The TV and furniture
will be unstable and may tip.
• The TV must weigh less than 95 lbs.
• The base of the TV must be able to sit
completely on this shelf.
Pand Q
R(13)P(4) Q(4)

14 DX-WD1201
Need help? Call 800-305-2204
Still need help?
For customer service, call: 800-305-2204 (U.S./Canada markets)
Distributed by Best Buy Purchasing, LLC
7601 Penn Avenue South, Richfield, MN USA 55423-3645
© 2012 BBY Solutions, Inc.
All rights reserved. DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All other
products and brand names are trademarks of their respective owners.

15
DX-WD1201
Need help? Call 800-305-2204
This page intentionally left blank.

www.dynexproducts.com [phone]
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave. South, Richfield, MN 55423 U.S.A.
© 2012 BBY Solutions, Inc.
All rights reserved.
DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All other products and
brand names are trademarks of their respective owners.
12-0782
ENGLISH
Certificate of Conformity
1. This certificate applies to the Sauder
Woodworking Product identified by this
instruction booklet.
2. This certificate applies to the compliance of this
product with the CPSC Ban on Lead-Containing
Paint (16 CFR 1303).
3. This product was manufactured by:
Sauder Woodworking Company
502 Middle Street
Archbold, Ohio 43502
[phone]
4. Date of Manufacture: _________________
Lot number: 345973