Dynojet Power Vision User manual

POWER VISION
INSTALLATION GUIDE
1POWER VISION
1REFLASH HARNESS
1USB CABLE
2VELCRO
2DYNOJET DECAL
Ski-Doo 900 Ace Turbo
PARTS LIST
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
2191 MENDENHALL DRIVE, NORTH LAS VEGAS, NV 89081
800-992-4993 98200118WWW.DYNOJET.COM

98200118 SKI-DOO 900 ACE TURBO
INTRODUCTION
INSTALLING THE POWER VISION
POWER VISION OVERVIEW—SIDE VIEW
Thank you for purchasing the Power Vision from Dynojet
Research. The Power Vision is the device to interface
between your computer and vehicle ECU allowing you
to tune your stock ECU to achieve optimal performance
from your vehicle.
Use the buttons to navigate the device menus, make
selections, cycle through the four available gauge
screens, and log data. Connect to the diagnostic port
to flash a tune; use the USB connection to interface
between the Power Vision and your computer.
Download the Power Core software and take tuning to a
whole new level.
1 Go to www.dynojet.com/PowerVision.
2 From the top navigation menu, select Support>Downloads.
3 Select Power Vision CX from the drop-down menu.
4 Download the Dynojet Power Core software.
5 Double-click the saved file to begin installation. Follow
the on-screen prompts. Refer to the Power Core Help for
more information.
1 Secure the Power Vision to the vehicle using the supplied
Velcro
. Make sure the Power Vision will not interfere with
the operation and steering of the vehicle.
Note: The Power Vision does not need to be mounted
to the vehicle.
2 Attach the diagnostic cable to the diagnostic port on the
Power Vision and to the diagnostic port on the vehicle.
900 Ace Turbo Models: located near the coolant bottle
above the chaincase.
SCROLL
INSTALLING THE POWER CORE SOFTWARE
USB CABLE PORT
CONNECT TO COMPUTER
DIAGNOSTICS CABLE PORT
CONNECT TO VEHICLE
POWER VISION OVERVIEW—FRONT VIEW
DIAGNOSTIC PORT
HOME/LOG
SCROLL
ENTER
RETURN

INSTALLATION GUIDE
This menu allows you to view the device status (paired/not
paired), VIN #, Model ID, ECU serial number, tune compat, and
checksum compat.
Select Vehicle Tools>Vehicle Information.
GETTING STARTED
Use the Tune File Wizard to prepare your Power Vision
device with the stock (stk) and tune (djt) files needed to
flash your vehicle.
1 Connect the Power Vision to the vehicle.
2 Turn the key on. The Power Vision will scan for files.
There are three possible file states:
File State 1: No compatible stock files.
File State 2: No compatible tune files.
File State 3: All required files found.
3 Gauges are displayed.
FLASHING YOUR VEHICLE
The Power Vision must be paired to the connected vehicle ECU
to function properly.
Note: Once paired to the vehicle ECU, the Power Vision will
not work on another vehicle without purchasing a tune
license.
1 From the Main Menu, select Flash Tune.
2 Select the tune file and press Enter to view the Tune Info.
3 Press Enter to accept the tune and pair the Power Vision to the
vehicle.
Note: Pair to vehicle will only happen on the first flash.
4 Press Enter to pair and lock the Power Vision to the ECU and to
begin the flash. Do not turn off the key switch or disconnect the
Power Vision during the flash.
5 After the flash is complete, turn the key off and wait 45 seconds
before turning the key back on to start.
FLASH TUNE
2507002.djt
2507001.stk
2507001.djt
TUNE INFO
FILE: 2507001.djt
PRESS TO START ECU FLASH
TUNER:
COMPATS: 7B2164PC8VLS1
DESCRIPTION: 2017 Ski-Doo Ace 900 Turbo
7B2164PC8VLS1
Stock intake
Stock exhaust
VEHICLE INFO
PAIRED VEHICLE: DEVICE NOT PAIRED
VIN: 3JBV6AWZ4HK000560
MODEL ID: 666939
TUNE COMPAT: 7B2164PC8VLS1
CSUM COMPAT:
VIEWING THE VEHICLE INFORMATION
File State 2:
Go to www.dynojet.com/pvtunes to
download tune files.
File State3:
All required files found. The Power
Vision is ready to flash a tune to the
connected vehicle.
Connect the Power Vision to the
vehicle diagnostic port to collect
ECU information. Turn the key on.
File State 1:
Go to www.dynojet.com/pvtunes to
download stock and tune files.

98200118 SKI-DOO 900 ACE TURBO
CONFIGURING GAUGES AND LOGGING DATA
This menu allows you to configure up to four different gauge
screens. Each gauge screen has four configurable channels.
1 From the Main Menu, select Device Tools>Configure Gauges.
2 Select a gauge screen and press Enter.
3 Select a channel and press Enter.
4 Select a channel from the list and press Enter.
5 Select the precision or units for that channel and press Enter.
6 Continue setting up the remaining channels as desired.
7 Continue configuring the remaining gauge screens as desired.
8 Press the Log button to begin logging. Press the Log button
again to stop logging.
9 Use the Power Core software to view log files.
Snapshot Log: Press and hold the Log button for two
seconds to record a two minute log.
DELETING DATA LOGS
This menu allows you to delete data logs.
Select Vehicle Tools>Delete Data Log.
This menu allows you to read and clear diagnostic trouble
codes.
1 To read codes, select Vehicle Tools>Diagnostics>Active
Codes.
2 To clear codes, select Vehicle Tools>Diagnostics>Clear
Codes.
VIEWING THE DIAGNOSTIC CODES

INSTALLATION GUIDE
VIEWING THE DEVICE INFORMATION
This menu allows you to view the device firmware version,
serial number, and stock code.
Select Device Tools>Device Information.
REFORMATTING THE DISK
This menu allows you to reformat the disk and erase all data.
Select Device Tools>Reformat Disk.
CHANGING THE SETTINGS
This menu allows you to rotate the screen allowing you to
change the orientation of the Power Vision device along with
adjusting the screen brightness.
Select Device Tools>Settings>Rotate Screen to flip the
screen.
Select Device Tools>Settings>Brightness to change the
screen brightness.
This menu allows you to update the device with the latest
firmware.
Select Device Tools>Update Device.
UPDATING THE DEVICE

PUSH THE LIMIT.
WWW.DYNOJET.COM
© 2018 DYNOJET RESEARCH ALL RIGHTS RESERVED