Cleaning the Clear binTM
Caution:
(i) Do not immerse the whole cyclone in water or pour water into the cyclones.
(ii) Ensure bin is completely dry before replacing.
Please note:
(i) Do not use detergents, polishes or air fresheners to clean the bin.
(ii) Do not put bin in a dishwasher.
(iii) When vacuuming, certain carpets may generate small static charges in the clear bin™.
These are entirely harmless and are not associated with the mains supply. To minimise
any effect from this, do not put your hand or insert any object into the clear bin™ unless
you have rst emptied it and rinsed it out with cold water.
Washing your lters
Caution:
(i) Switch ‘OFF’ and unplug machine before removing the lters.
(ii) Ensure lters are completely dry before retting to machine.
This machine has two lters, located as shown. It is important to check your lters regularly
and wash at least every 3 months according to instructions, to maintain performance.
The lter in the ball should be rinsed and tapped out until the water runs clean, then tapped
out again to ensure all excess water is removed. This will normally require up to 10 rinse cycles.
Please leave to dry completely for 24 hours.
Please note:
(i) It is normal for the lter in the ball to turn grey in colour. The lters may require more
frequent washing if vacuuming ne dust.
(ii) Do not use detergents to clean the lters.
(iii) Do not put the lters in the dishwasher, washing machine, tumble dryer, oven,
microwave or near an open ame.
Looking for blockages
Caution:
(i) Switch ‘OFF’ and unplug machine before checking for blockages.
(ii) Please ensure machine is upright before removing hose or airway inspection parts.
(iii) Beware of sharp objects when clearing blockages.
(iv) Ret all parts of the machine securely before using.
Please note:
(i) Clearing blockages is not covered by your machine’s limited warranty. If any part
of your machine becomes blocked, it may overheat and then automatically shut off.
Unplug machine and leave to cool down. Clear blockage before restarting.
Clearing brushbar obstructions
Caution:
(i) Switch ‘OFF’ and unplug machine before clearing brushbar obstructions.
If your brushbar is obstructed, it may shut off. If this happens you will need to remove
brushbar as shown and clear any obstructing debris.
Conformity information: A sample of this product has been tested and found to conform with the following
European Directives: 2006/95/EC Low voltage Directive, 2004/108/EC EMC Directive, 93/68/EEC CE
Marking Directive.
Product information: Net weight 7.5kg, 230-240V, 50Hz, maximum power 1200W.
This product is protected by the following intellectual property rights:
Patent/Patent Application numbers: JP 2004-537336; EP 1361812; AU 744408; EP1119282; JP 2002-527132;
US 6,519,807; AU 744362; EP 1121043; JP 2002-527131; US 6,572,078; GB 0326102.1; AU 2002-226556;
EP 1370172; JP 2004-528876; US 6,991,666; AU 2002-225207; EP 1361814; JP 2004-520137; US 7,018,439;
AU 2001-240894; EP 1268076; JP 2003-528704; US 6,835,222; AU 2002-225232; EP 1361815;
JP 3940082; US 6,974,488; AU 2003-283157; EP 1526796; JP 2006-503607; US 2005-0235454;
AU 2003-283159; EP 1526797; JP 2005-534442; AU 2003-283161; EP 1526798; JP 2006-503608;
AU 2004-294771; EP 1680232; JP 2007-508934; US 2007-0079579; AU 2005-263889; EP 1768536
Equivalent patents, registered designs and applications exist in other countries.
Please note: Small details may vary from those shown.
SAVE THESE INSTRUCTIONS
THIS APPLIANCE IS INTENDED FOR NORMAL DOMESTIC USE ONLY