E-Seek M260 Installation and operation manual

Product Reference Guide
Product Reference Guide
Model M260
www.e-seek.com

Product Reference Guide

Product Reference Guide
Product Reference Guide
Model M260
2011 E-Seek Incorporated, All Rights Reserved.
E-Seek reserves the right to make changes to any product
to improve reliability, function, or design.
E-Seek does not assume any product liability arising out of,
or in connection with, the application or use of the product,
circuit, or application described herein.
No license is granted, either expressly or by implication,
estoppel, or otherwise under any patent right or patent,
covering or relating to any combination, system,
apparatus, machine, material method, or process in which
E-Seek products might be used. An implied license only
exists for equipment, circuits, and subsystems contained in
E-Seek products.
E-Seek logo are registered trademarks of E-Seek
Incorporated. Other product names mentioned in this
manual may be trademarks or registered trademarks of
their respective companies and are hereby acknowledged.
R & D Center
9471 Ridgehaven Court #E
San Diego, CA 92123
Tel: [phone]
Fax: [phone]
Sales & Marketing
245 Fischer Ave #D5
Costa Mesa, CA 92626
Tel: [phone]
Fax: [phone]
www.e-seek.com
Patented Product
1

Product Reference Guide
Parts of the Model M260 2D
Bar Code and Magnetic Stripe
Reader
This page will provide an illustrated breakdown of the
Model M260.
1. Cable Interface Connector
2. Power Supply Connector
3. Power On - Good Read LED
4. 2D Bar Code
5. Card Insertion Guide
6. Magnetic Stripe
2
1
2
3
4
5
6

Product Reference Guide3
Model M260 Product
The Model M260 is a 2D Bar Code Scanner designed
for reading and decoding 2D Bar Code on ID Cards and
Driver’s Licenses. The Model M260 presents decoded
Bar Code information through RS 232 interface or USB,
utilizing an RJ 45 connector and Kiosk connection.
The Model M260 provides a three track Magnetic Stripe
Reader incorporated into one integrated housing.
Multiple cable options are available to interface to various
systems and plug requirements.
7. Product ID Label
8. Kiosk Connector
7
8
Bottom View

Product Reference Guide 4
Cable Options
1. USB Cable
2. Serial Cable
3. Kiosk Cable
Installing the Kiosk Cable
Simply connect the kiosk male connector on the interface
cable to kiosk female connector built into the Models M260
as per the illustration below.
Mating Connector

Product Reference Guide5
Installing the Interface USB or
Serial Cable
Simply connect the RJ 45 male connector on the interface
cable to RJ 45 female connector built into the Models M260
as per the illustration below.
Installing the Power Supply
Simply connect the Power Supply Module to a convenient
AC outlet and the cable to the Model M260 as shown
below. No power connection is required for Verifone
terminals.

Product Reference Guide
Scanning a 2D Bar Code
Simply insert and remove the card to be read in a smooth
and continuous motion. The reader will emit a double beep
tone and the green LED will ash on a good read. Orient
the bar Code to be read in accordance with the illustration
below.
Reading a Magnetic Stripe
Orient the card to be read as illustrated below, and simply
swipe the card through the reader in one smooth and
continuous motion in either direction.
6

Product Reference Guide7
What does the Beep Mean?
When power is applied to the unit, it is automatically
powered on, runs a self-diagnostic test and issues
three beep tones to signify that it is operational.
When the unit is programmed (see Programming
Manual) it will emit a Melody tone to signify that it
has successfully been programmed.
When a Bar Code has successfully decoded the unit
will emit a beep tone.
1.
2.
3.
Technical
For downloading the program guide or to contact us,
please visit our website at www.e-seek.com.

Product Reference Guide
Regulatory Information
Radio Frequency Interference
Requirements
The Model M260 have been tested and found to comply
with the limits for a Class B digital device pursuant to Part
15 of the FCC Rules and Regulations. These limits are
designed to provide reasonable protection against harmful
interference when the equipment operated in a commercial
environment. This equipment generates, uses, and can
radiate radio frequency energy, and if not installed and
used in accordance with the instruction manual, may cause
harmful interference to radio communications.
These devices comply with FCC Part 15. Operation is
subject to the following two conditions:
These devices may not cause harmful interference.
These devices must accept any interference received,
including interference that may cause undesired
operation.
1.
2.
8

Product Reference Guide9
Radio Frequency Interference
Requirements – Canada
The Model M260 comply with RSS 210 of Industry &
Science Canada. These Class B digital devices comply with
Canadian ICES-003.
CE Marking and European Union
Compliance
Products intended for sale within the European Union are
marked with the CE Mark which indicates compliance to
applicable Directives and European Normes (EN). The
Model M260 have been tested and are certied to meet all
applicable Directives and European Normes.

Product Reference Guide 10
Specications
Decoder Two Dimensional
PDF417
Linear Barcodes
Code 39 & Code 128
Card Operating Mode
Hands-free, Manual Insertion of
ID card or Magnetic Stripe Swipe
action
Interface
- RS-232C Serial Port
- USB 2.0 Full speed (w/FTDI
drivers, Windows certified)
Power Consumptions
4 mA @ 5VDC - Standby; 250 mA
Maximum
Dimensions
2.13” H x 2.28” W x 4.33” D
Weight
0.5 Pound
Card Size
ISO/IEC-7811, ID-1 Standard Size
3.370" x 2.125"
Housing
ABS Plastic in Black
Operating Temperature
32 to 122° F (0 to 50° C)
Humidity
10% to 90%, non-condensing

Product Reference Guide
Appendix A
Mounting picture. (Inch)
11
#4-40 HOLES
2 PLACES
2.04
4.33
2.28

Product Reference Guide 12
Appendix B
No
Function
Direction
Remark
1
VUBS
IN
POWER from USB +5V
2
VCC
IN
+15V DC
3
D-
IN/OUT
USB DEVICE
4
D+
IN/OUT
USB DEVICE
5
GND
--
6
TXD
OUT
RXD on host
7
RXD
IN
TXD on host
8
RTS
OUT
CTS on host
9
CTS
IN
RTS on host
10
NC
--
Serial Port Pin outs (RJ-45 & Kiosk)
Kiosk Connector Pin Position
Molex 0430451000
Mating Connector: Molex 0430251000
#10
#5
#6
#1
#2

Product Reference Guide
NOTES
13

Product Reference Guide
201100-C0