Eagle power SD2000 Application guide

REV A April 2003
SD2000
FLOOR
BURNISHER
OPERATION & PARTS MANUAL

SPECIFICATIONS
Length: 33.75 inches
Width: 21 inches
Height: 50 inches
Weight: 69 pounds
Pad Speed: 2000
Pad Diameter: 20 inches
Drive Motor: 1.5 HP, 120V, 15A, 50/60 HZ
Power Cord: 14-3 ST, 75 feet
SAFETY
Read and understand the manual
before operating this machine.
Do not operate in explosive areas or use near
flammable liquids or gases.
Attach only to properly grounded outlet.
Do not expose to rain. Store indoors.
Do not operate the machine with a damaged cord
or plug.
Do not block or disconnect the safety lever.
Do not leave the machine plugged in while
unattended.
Unplug the machine before servicing.
Do not put fingers under the pad or pad holder.
Unplug the machine before installing or removing
the pad.
Use only with Hi Speed Burnishing pads.
OPERATING INSTRUCTIONS
Check machine for damage to cord or
plug.
Use only Hi Speed Burnishing pads
20” or 19” diameter.
To install or change the pad:
1. Unplug the machine.
2. Tip the machine back on the wheels.
3. Remove the center-lock
4. Center the pad on the pad driver.
5. Replace the center-lock and tighten securely.
To operate the machine:
1. Plug into a grounded outlet.
2. Release the handle and lower it.
3. The handle can be locked into a comfortable
position for the operator or used free floating.
4. Press the safety lever and squeeze the trigger to
start the machine.
5. Do not operate in one place as damage to the
floor could result.
6. Do not operate the machine with the handle in
upright position.
7. Remove the pad after every use.
8. Store the machine tilted back on the transport
wheels.
9. Use only new or clead pads and reverse them
as needed.
Maintenance
To maintain appearance - wipe the machine with a
damp cloth after use.
WARNING - Unplug the machine before servicing.
CHECK EVERY 250 HOURS OF USE.
1. Check the motor brushes for wear or excessive
arcing.
2. Check belt tension.
3. Check the cord and electrical system.
4. Check the safety lockout on the trigger.
5. Check wheels and bearings.

Part # Description QTY Fig.
1 N310122 Switch box, handle 1
1N310121 Cover, switch box 1
1 N210102 Switch 1
1 N310124 Handle tube 7/8 x 16” 1
1N310118 Grips 2
1 N310120 Trigger, switch 1
1 N310119 Safety lock 1
1N110149 Spring 1
1 N110163 Clip, spring 1
1N310103 Cord, 75’ - 14-3 1
1N210105 Cord, handle 14-3 1
1 N210106 Grommet 3/8 ID 1
1 N310125 Handle, weldment 1
1 N110150 Screw 1/4-20 x 3/4 2
1N110115 Nut, 1/4-20 Nylok 2
1 N110140 Screw 1/4-20 x 1 3/4 4
1N210109 Wire, ground 1
1N210110 Wire nut 2
1 N110146 Wire tie 1
1 N110116 Screw #6 2
1 N110159 Decal, Safety 1
1N110105 Serial Tag 1
1N110171 Decal, Made in USA 1
PARTS LIST ILLUSTRATION
2 N310102 Pulley, 1600 RPM 1
2N110155 Spacer, .75 ID 1
2 N110145 Spacer, pulley brgs 1
2N310109 Bracket, pulley mt. 1
2 N310134 Belt, 2000 1
2 N110120 Washer, lock 5/16 1
2 N110123 Washer, flat 3/8 8
2 N110126 Bolt, 1/8-16 x 1/25 5
2 N110125 Bolt, 3/8-16 x .75 4
Part # Description QTY
Fig.
2 N310103 Pulley, 2000 RPM 1
2N310105 Pulley, pad drive 1
2N110102 Bearing 2
2 N310123 Belt, 1600 1
2 N110119 Washer, flat 5/16 USS 1
2N110152 Bolt, 5/16-18x1” Hex 1
2N110124 Washer, lock 3/8 8
2N110127 Nut, 3/8-16 1
2 N110165 Bolt, 3/8-16 x 1” 1
Fig 1
Fig 2

3
3
3
3
N110144
N310101 Base, high speed
Part #
3 N310116
N310115
3 N310132
N310112
3N310114
N210101
3
Fig.
Caps, axel 1/2”
Axel, 1/2” x 17.25” 1
Axel, 1/2” x 13.875”
Axel, 1/2” x 12 3/8” 1
Wheel 4”
Wheel 5” 2
Motor, 1.5 HP
1
Description QTY
6
1
2
1
PARTS LIST ILLUSTRATION
Fig 5
Fig 4
Part # Description QTY Fig.
4N310129 Handle cam lock
2
Washer, nylon
1
4 N110112 Washer, oval
4 N110148 Nut, 5/16-18 Nylock
1
1
1
7
4N110103
4N310128 Cord hook
N310130 Bracket, handle 1
N110114 Pin 1/4 x 3/4
N110164 Washer, spring 1/4” 1
N110151 Cap, push 1/4”
N110169 Washer, spring 3/8” 1
N110168 Washer, spring, 1/2”
7
4
4
4
4
N110111
4
4
4Bolt, adj. 5/16-18 cam
1
1
1
5 N310117 Cover, motor, gray 1
5 N110141 Screw 1/4-20 x 1” 4
5N110143 Washer 1/4 lock 4
5 N110150 Screw 1/4-20 x 3/4
5 N310106 Pad driver assy. 1
Part # Description QTY Fig.
5N210108 Hour meter 1
5N110142 Washer 1/4 flat 4
5N310111 Bumper 1
5 N110130 Washer, fender 1/4” 1
5N110166 Screw 5/16-18 x 1.25 1

Please be sure to record this information. This information will be necessary for future warranty claims.
Serial Number:
Date Purchased:
Model Number:
Eagle Power Products Sales and Service Provided by:
1174 Northland Drive Mendota Heights, MN 55120
651.686.5399 Fax [phone]
www.eaglepower.com
Warranty Policy
Limited Warranty
Eagle Power Products (EPP) warrants new cleaning equipment against defects in material and
workmanship under normal use and service to the original purchaser as detailed below.
10 Years
Subject to the conditions stated below, EPP warrants polyethylene tanks and housings to be
free from defects in materials and workmanship for a period of ten years.
3 Years
Subject to the conditions stated below, EPP warrants all automatic scrubber components to
be free from defects in materials and workmanship for a 3-year period. Parts replaced or
repaired are warranted for the remainder of the original warranty period.
1 Year
Subject to the conditions stated below, EPP warrants all other cleaning equipment
components to be free from defects in materials and workmanship for a 1-year period. Parts
replaced or repaired are warranted for the remainder of the original warranty period.
Batteries are prorated for one year.
EPP will furnish and charge for replacement parts, including transportation, to the original
owner through an EPP authorized service center. If the part is returned within 30 days and is
found defective, the owner will be credited for the cost of the replacement part including
shipping and handling.
Labor charges are covered for one year from the date of purchase if provided by an authorized
EPP service center. Travel is covered for 90 days for battery operated equipment only.
Wear items exempt from warranty include belts, carbon brushes, power cords, wheels, pad
drivers, clutch plates, brushes, pads, handle grips, filters, screens, throttle cables, and squeegees.
This warranty shall not apply to failures caused by misuse or abuse, improper
maintenance as stated in the operation manuals, use of unauthorized repair parts, repairs
by other than an EPP authorized service center, and damage in transit.
EPP disclaims and denies any liability for any direct, indirect, special incidental or consequential damage which may
be suffered as a result of sale, delivery, servicing, use, loss of any product, downtime, labor, freight, or other charges
not expressly included herein.