Eagle A3 Pro User manual

Version 1.0
www.geeetech.com
1
/
2
[e-mail]
Thank you for purchasing EAGLE series of flight controller. If any difficulties are encountered while setting up or operating your A3 Pro, please consult this manual
first. For further help, you may also visit our website at www.geeetech.com , or contact us via email [e-mail]
Features
Features
Features
Features
★
3 F light M odes can be switched between Normal
Normal
Normal
Normal Mode
Mode
Mode
Mode ,AVCS
AVCS
AVCS
AVCS Mode
Mode
Mode
Mode and Gyro
Gyro
Gyro
Gyro Off
Off
Off
Off in flight;
★
3 M odel T ypes supported : Normal
Normal
Normal
Normal Airplane
Airplane
Airplane
Airplane ,Flying-wing
Flying-wing
Flying-wing
Flying-wing (Delta-wing)
(Delta-wing)
(Delta-wing)
(Delta-wing) and V-tail
V-tail
V-tail
V-tail ;
★Specifically optimized to work for 3D flight ;
★
I ndependent gyro gain adjustment for Aileron, Elevator and Rudder;
★
Basic setting functions including Stick Centering and Gyro Reversing ;
★Smaller and lighter, more compatible with small airplane;
★Firmware can be updated from PC easily.
Specifications
Specifications
Specifications
Specifications
Voltage Range: 4 - 6V DC
PWM Output: 50Hz /1520 µ s , 1020 ~ 2020 µ s
Full-Scale Range of Gyro: ± 1000dps
Sample Rate of Gyro: 1KHz
Operating Temperature: -40
℃
to 85
℃
Dimensions: 30 × 40mm
Weight: 8 g
Attentions
Attentions
Attentions
Attentions
1. Make sure that your plane has been well installed before use;
2. In order to make the best use of your board, please read this manual carefully and install it step by step following the instructions below;
3. Set the trimming and sub-trim parameters to “ 0 ” for channels of aileron, elevator and rudder within your transmitter;
4. Verify
Verify
Verify
Verify that
that
that
that the
the
the
the mixing
mixing
mixing
mixing of
of
of
of flying-wing
flying-wing
flying-wing
flying-wing (delta-wing)
(delta-wing)
(delta-wing)
(delta-wing) or
or
or
or v-tail
v-tail
v-tail
v-tail has
has
has
has been
been
been
been disabled
disabled
disabled
disabled within
within
within
within your
your
your
your transmitter
transmitter
transmitter
transmitter as
as
as
as A3
A3
A3
A3 Pro
Pro
Pro
Pro has
has
has
has already
already
already
already built
built
built
built these
these
these
these functions
functions
functions
functions in.
in.
in.
in.
Installation
Installation
Installation
Installation Guide
Guide
Guide
Guide
【
【
【
【Step
Step
Step
Step 1:
1:
1:
1: Board
Board
Board
Board Mounting
Mounting
Mounting
Mounting 】
】
】
】
The board need to be firmly mounted near the center of gravity of the plane, by the double sided tape provided. Please make sure the longer side of the board is
along with the heading direction. The board must be leveled with the body of the plane. Please refer to the illustration below.
【
【
【
【Step
Step
Step
Step 2:
2:
2:
2: Wiring
Wiring
Wiring
Wiring 】
】
】
】
Once installation is completed, please connect the channels of aileron, elevator, rudder and switch from your receiver to the pins marked “ IN ” , pin 1 for aileron, pin
2 for elevator, pin 3 for rudder and pin 4 for the flight mode switch ( You
You
You
You should
should
should
should directly
directly
directly
directly connect
connect
connect
connect the
the
the
the throttle
throttle
throttle
throttle channel
channel
channel
channel to
to
to
to ESC
ESC
ESC
ESC or
or
or
or throttle
throttle
throttle
throttle servo
servo
servo
servo without
without
without
without
bridging
bridging
bridging
bridging the
the
the
the board
board
board
board ). Connect the servos to the pins marked “ OUT ” , pin 1 for aileron servo, pin 2 for elevator servo and pin 3 for rudder servo. When the aileron is
operated by two separate servos, you should use a Y extension cable. Pay attention to the color of wires to avoid anti-plug.
【
【
【
【Step
Step
Step
Step 3:
3:
3:
3: Model
Model
Model
Model Type
Type
Type
Type Selection
Selection
Selection
Selection 】
】
】
】
A3 Pro uses a 3-bit jumper (J1-2-3) for model type selection. Please match the type of your plane with Normal Airplane, Flying-wing (Delta-wing) and V-tail
according the table as shown below. Restart
Restart
Restart
Restart the
the
the
the board
board
board
board to
to
to
to activate
activate
activate
activate the
the
the
the selected
selected
selected
selected type
type
type
type .
No.
No.
No.
No. Model
Model
Model
Model Types
Types
Types
Types
Jumper
Jumper
Jumper
Jumper Setting
Setting
Setting
Setting Servo
Servo
Servo
Servo Connection
Connection
Connection
Connection
J1
J1
J1
J1 J2
J2
J2
J2 J3
J3
J3
J3 OUT-1
OUT-1
OUT-1
OUT-1 OUT-2
OUT-2
OUT-2
OUT-2 OUT-3
OUT-3
OUT-3
OUT-3
1 Setting Mode 0 0 0 - - -
2 Normal Airplane ▲ 1 0 0 Aileron Servo Elevator Servo Rudder Servo
3 Flying-wing (Delta-wing) 0 1 0 Left Wing Servo Right Wing Servo * Rudder Servo
4 V-tail 0 0 1 * Aileron Servo Left Tail Servo Right Tail Servo
Notes: “ 0 ” represents “ OPENED ” , “ 1 ” represents “ CLOSED ” , “ ▲” is the default setting.
【
【
【
【Step
Step
Step
Step 4:
4:
4:
4: Gyro
Gyro
Gyro
Gyro Gain
Gain
Gain
Gain Setting
Setting
Setting
Setting 】
】
】
】
A3 Pro offers 3 fine tuning potentiometers to adjust the gyro gain for aileron, elevator and rudder (clockwise for increase, anticlockwise for
decrease). The best setting is determined by factors like fuselage size, weight and the power allocation used and so on. W e recommend
you put the gain to a lower volume for the first flight, then fine tune to get the best result. The adjustment will take effect immediately without
a restart. For your safety, please don ’ t adjust them until all the propellers become motionless.
【
【
【
【Step
Step
Step
Step 5:
5:
5:
5: Switch
Switch
Switch
Switch Channel
Channel
Channel
Channel Configure
Configure
Configure
Configure 】
】
】
】
Assign a 3-position switch to the channel which connected to the pins “ IN-4 ”
for switching the flight mode in flight. When use a 2-position switch, you can
only switch between Normal Mode and AVCS Mode. It will be set to Normal
Mode by default if the switch channel is not connected to the board.
However
However
However
However it
it
it
it is
is
is
is not
not
not
not recommended
recommended
recommended
recommended as
as
as
as the
the
the
the board
board
board
board might
might
might
might get
get
get
get interrupted
interrupted
interrupted
interrupted by
by
by
by
the
the
the
the reception
reception
reception
reception during
during
during
during the
the
the
the flight,
flight,
flight,
flight, which
which
which
which will
will
will
will result
result
result
result in
in
in
in the
the
the
the unexpected
unexpected
unexpected
unexpected
flight
flight
flight
flight mode
mode
mode
mode . When the board is operating, the indicator lights show the current flight mode, blue for normal mode, red for AVCS mode and both blue and red off
indicates that the gyro has been disabled.
【
【
【
【Step
Step
Step
Step 6:
6:
6:
6: Stick
Stick
Stick
Stick Centering
Centering
Centering
Centering 】
】
】
】
To get the best result, you should apply the “ Stick Centering ” function to calibrate channel range following the Map of Setting Methods. For the first use of A3 Pro
No.
No.
No.
No. Flight
Flight
Flight
Flight Modes
Modes
Modes
Modes Switch
Switch
Switch
Switch Position
Position
Position
Position Pulse
Pulse
Pulse
Pulse Range
Range
Range
Range LED
LED
LED
LED
1 Normal Mode ▲ ON < 1320 µ s Blue
2 Gyro Off MID DLE 1520 ± 200 µ s O ff
3 AVCS Mode OFF > 1720 µ s Red
All manuals and user guides at all-guides.com
all-guides.com

Version 1.0
www.geeetech.com
2
/
2
[e-mail]
or replacing a new radio system, calibration is needed to obtain the best performance . After calibration , the servos will center, center
center
center
center the
the
the
the aileron,
aileron,
aileron,
aileron, elevator
elevator
elevator
elevator and
and
and
and
rudder
rudder
rudder
rudder of
of
of
of your
your
your
your plane
plane
plane
plane by
by
by
by adjusting
adjusting
adjusting
adjusting the
the
the
the length
length
length
length of
of
of
of the
the
the
the linkage
linkage
linkage
linkage rods,
rods,
rods,
rods, It
It
It
It is
is
is
is NOT
NOT
NOT
NOT recommended
recommended
recommended
recommended to
to
to
to adjust
adjust
adjust
adjust it
it
it
it through
through
through
through the
the
the
the “
“
“
“ Sub-Trim
Sub-Trim
Sub-Trim
Sub-Trim ”
”
”
” function
function
function
function within
within
within
within your
your
your
your
transmitter
transmitter
transmitter
transmitter directly
directly
directly
directly as
as
as
as it
it
it
it might
might
might
might reduce
reduce
reduce
reduce the
the
the
the performance
performance
performance
performance of
of
of
of A3
A3
A3
A3 Pro
Pro
Pro
Pro . Stick Centering works on of aileron, elevator and rudder channels. To enter this function,
you must get IN 1-2-3 ready.
【
【
【
【Step
Step
Step
Step 7:
7:
7:
7: Before
Before
Before
Before Flight
Flight
Flight
Flight Checking
Checking
Checking
Checking 】
】
】
】
Verify
Verify
Verify
Verify that
that
that
that the
the
the
the gyro
gyro
gyro
gyro compensation
compensation
compensation
compensation is
is
is
is in
in
in
in the
the
the
the correct
correct
correct
correct direction
direction
direction
direction for
for
for
for the
the
the
the first-time
first-time
first-time
first-time installation,
installation,
installation,
installation, otherwise,
otherwise,
otherwise,
otherwise, it
it
it
it could
could
could
could lead
lead
lead
lead to
to
to
to losing
losing
losing
losing control
control
control
control or
or
or
or even
even
even
even crash
crash
crash
crash during
during
during
during
the
the
the
the flight!
flight!
flight!
flight! Turn on the board, pick the plane up and check it by following the 6 steps shown below :
①Rise the head up around the pitch axis, the elevator should flap down accordingly; ②Put the head down around the pitch axis, the elevator should flap up
accordingly. ③
③
③
③Rotate left around the roll axis, the left aileron should flap down and the other one flap up accordingly; ④Rotate right around the roll axis, the left
aileron should flap up and the other one flap down accordingly;
⑤
Rotate right around the yaw axis, the rudder should turn left accordingly;
⑥
Rotate left around
the yaw axis, the rudder should turn right accordingly.
I f the gyro compensates in an incorrect direction, reverse it by following the instructions of Gyro Reversing Function below.
Map
Map
Map
Map of
of
of
of Setting
Setting
Setting
Setting Methods
Methods
Methods
Methods
LED
LED
LED
LED Indicator
Indicator
Indicator
Indicator Description
Description
Description
Description
Condition
Condition
Condition
Condition LED
LED
LED
LED Indicator
Indicator
Indicator
Indicator Description
Description
Description
Description
Initialization
Blue, 1 flash after power on Initialize success, type of Normal Airplane selected
Blue, 2 flashes after power on Initialize success, type of Flying-wing(Delta-wing) selected
Blue, 3 flashes after power on Initialize success, type of V-tail selected
Red, very rapid flashing Undefined Model Type, check the setting of jumper J1-2-3
Operating
Solid Blue Normal M ode , ready for flight
Solid Red AVCS Mode, ready for flight
Both Off Gyro is disabled, ready for flight
Setting Mode Red, slow flashing No signal, you must get IN 1-2-3 connected before entering setting mode.
All manuals and user guides at all-guides.com