EARDATEK KINGSAT KM-V3 User manual

KINGSAT Satellite TV Antenna System
1
www.kingsat-tech.com
[e-mail]

KINGSAT Satellite TV Antenna System
2
Table of Contents
1. INTRODUCTION..................................................................................... 3
1.1 Introduction to KINGSAT KM-V3/V4/V6/V7.................................3
1.2 Features of KINGSAT KM-V3/V4/V6/V7....................................... 3
2. INSTALLATION........................................................................................ 5
2.1 Preparation................................................................................... 5
2.2 Planning the Installation...............................................................6
2.3 Installation and Mounting of Antenna.........................................7
2.4 Installing the ACU....................................................................... 12
3. OPERATION INSTRUCTION.................................................................. 16
3.1 Introduction................................................................................ 16
3.2 Operating the ACU......................................................................17
3.3 Error Code and Solutions........................................................... 28
4. PREPARATION FOR TRANSPORTATION................................................29

KINGSAT Satellite TV Antenna System
3
1. INTRODUCTION
1.1 Introduction to KINGSAT KM-V3/V4/V6/V7
KINGSAT KM-V3/V4/V6/V7 is a digital satellite antenna system. It’s designed for all
types of vessels to automatically search, track and capture satellite signal from the
Digital Video Broadcasting (DVB) compatible satellites.
Figure 1: Maritime Satellite TV Antenna
1.2 Features of KINGSAT KM-V3/V4/V6/V7

KINGSAT Satellite TV Antenna System
4
Strong Signal Receiving performance
Using self-made LNB and RF processing components, which offers the best reception
quality and maximum antenna performance.
Fast Satellite Search and Position
An integrated GPS antenna allows for the antenna control system to update the GPS
data automatically for accurate positioning and faster satellite locking.
Excellent Anti-Heavy Sea Tracking Ability
Proprietary algorithm, advanced mechanical design, embedded GPS and
high-sensitive gyro enable always-lock connectivity and worldwide deployment.
Expendable Worldwide Satellite Library
The ACU is installed with Worldwide satellite database and can be easily revised or
expended manually.
Easy-to-install Aesthetic Design
Simple installation and setup design with aesthetic maritime white of
environment-resistant feature save labor and maintenance costs.

KINGSAT Satellite TV Antenna System
5
2. INSTALLATION
2.1 Preparation
Standard components
Antenna Unit*1
Antenna Control Unit(ACU)*1
24V/3A Adapter for ACU*1
Hex head bolt , Spring washer , Flat washer , Nut , Mounting bracket , Tapping screw
Cables:
15-meter coaxial cable * 2
Power cable*1
*M8 is applicable on V3/V4/V6, M12 is applicable on V7.
Figure 2: Required Tools for Installation

KINGSAT Satellite TV Antenna System
6
2.2 Planning the Installation
Antenna Unit
Install the antenna in accordance with the following procedures to ensure maximum
performance of the antenna.
The antenna must be installed at the position:
(1) It has an all-around clear view of the horizon.
(2) There are no obstacles within 1 degree above the antenna.
(3) Far away from the Radar.
Figure 3: Position of Radar and Antenna
(4) The mounting platform should be firm enough and not subjected to excessive
vibration.
Figure 4: Elevation Limit of Obstacles

KINGSAT Satellite TV Antenna System
7
Cables
Cables must be routed correctly. Before installing the system cables, consider the
following points:
(1) All cables need to be well clamped and protected from physical damage and
exposure to heat and humidity.
(2) Do not bend cables excessively.
(3) Where a cable passes through an exposed bulkhead or deck head, a watertight
grommet or swan neck tube should be used.
Power Requirement
Following the power requirement to avoid damage to the system. KINGSAT
KM-V3/V4/V6/V7 has been designed to work on a boat which power supply is in the
range of 110-240V AC.
RF Cable
This cable is supplied at a length of 15m.If longer length is required you should
replace this cable with an extended RF cable supplied by Earda Technologies.
Note: Exceeding the indicated cable length will result in reduced performance of your
system.
2.3 Installation and Mounting of Antenna
The method of installation mounting of antenna may be due to vessel design but the
following procedures are applicable in most situations, and will result in a secure and
effective installation.
Confirmation of Size Prior to Installation
(1) Check the height and diameter of the bottom surfaces of the antenna before
installing.
(2) The space must be sufficient for installing the antenna unit considering the
height and diameter of the antenna.
(3) The height and the diameter of the bottom surface of the antenna are as shown
in the following drawings.
Note: Before installing the antenna, open the radome and remove the shipping
constraints from the antenna interior.

KINGSAT Satellite TV Antenna System
8
Figure 5.1: Radome Dimension of KM-V3 Figure 5.2: Radome Dimension of KM-V4
Figure 5.3: Radome Dimension of KM-V6 Figure 5.4: Radome Dimension of KM-V7

KINGSAT Satellite TV Antenna System
9
Confirming of the Antenna Mounting Position
Referring to the mounting template, mark where antenna will be mounted on board
(it must be a flat surface) or on a separate power tower.
Note: Exposed cable must be protected because an exposed cable may cause electric
shock and cause serious damage to the equipment.
Figure 6.3: Mounting Hole Position of KM-V6 Figure 6.4: Mounting Hole Position of KM-V7
Figure 6.1: Mounting Hole Position of KM-V3
Figure 6.2: Mounting Hole Position of KM-V4

KINGSAT Satellite TV Antenna System
10
Connection of the Cable
Remove the rubber cap from RF connector. Connect the RF cable to the RF connector
at the bottom of the base plate through the access hole using an adjustable spanner.
Be careful not to over tighten and damage the connector.
Note: Do not tighten excessively when using the spanner, it will damage the threads.
Be careful that the connectors do not touch the mounting surface of the antenna, it
might cause a critical malfunction and serious damage to the equipment.
Figure 7: Connectors on Bottom of Antenna

KINGSAT Satellite TV Antenna System
11
Mounting the Antenna
Attach the antenna by using the hex head bolts, spring washers, flat washers and nut
supplied.
There are two different ways for different models:
Figure 8.1: Mounting the Antenna
Figure 8.2: Mounting the Antenna
*M8 is applicable on V3/V4/V6, M12 is applicable on V7.

KINGSAT Satellite TV Antenna System
12
2.4 Installing the ACU
ACU Dimension
Figure 9: Dimension of ACU
Select ACU Installation Site
The ACU should be installed below desk, in a location that is:
(1) Dry, cool and ventilated.
(2) Easy accessed from your main TV viewing area.

KINGSAT Satellite TV Antenna System
13
Installing the ACU
(1) The ACU should be installed using the two supplied mounting brackets which are
allowed for a top or bottom mounting configuration.
(2) Using the self-tapping screws supplied, attach the mounting brackets to both
sides of the ACU.
(3) Place the ACU in the location where it is going to be installed.
(4) Connect the cables to the rear of the ACU
(5) Use a pencil to mark the position of 4 holes (two on each side), and use the
appropriate drill bit to drill.
Figure 10: Installation of ACU-Method 1
Figure 11: Installation of ACU-Method 2

KINGSAT Satellite TV Antenna System
14
Connecting the System Cables of KM-V3/V4/V6/V7
After installing and mounting the antenna, connect the ACU to the antenna. Refer to
the drawing shown below to connect cables.
Cable Connection
(1) Connect “RF1” on the antenna base plate to “ANT-RF1” on the ACU.
(2) Connect “RF2” or “RF3” or “RF4” on the antenna base plate to Receiver.
*Receiver is not included in the standard package
Figure 12: Cable Connection Configuration

KINGSAT Satellite TV Antenna System
15
Multi-Receivers Solution
In order to connect multi-Receivers to the antenna, you need to purchase a suitable
Multi Switch. The Multi Switch has to be installed between the antenna until and the
Receivers as shown in the following diagram.
*Multi Switch and STBs are not included in the standard package
Figure 13: Multi-Receivers Solution

KINGSAT Satellite TV Antenna System
16
3. OPERATION INSTRUCTION
3.1 Introduction
This section of the Manual describes how to setup your Satellite TV System using the
ACU. It includes the following functions:
Note: Many of the above functions will only be required after first installation of your
system. Refer to the User Manual before operating the system.

KINGSAT Satellite TV Antenna System
17
3.2 Operating the ACU
ACU Soft Keys
Figure 14: ACU Soft Keys

KINGSAT Satellite TV Antenna System
18
NORMAL MODE
1. START UP
With the system installed and power applied, the ACU screen will show the following
sequences:
Note: The operation method is the same for KM-V3/V4/V6/V7. The following
instruction will be described using KM-V3 as an example.
2. SLEEP MODE
The antenna will fall into sleep mode when it doesn’t lock satellite for 8 minutes. It
will wake up automatically after 10 minutes or changing target satellite
automatically.
3. The antenna is searching for Pre-set satellite.
2. Data communication is being established between the
antenna and the ACU. The ACU antenna are initialized.
1. Press POWER and the brand will be shown on MONITOR.
4. The antenna has locked the satellite and is now tracking.

KINGSAT Satellite TV Antenna System
19
3. CHANGE TARGET SATELLITE
The antenna is pre-programmed with up to 6 satellites as default mode.
You can change your target satellite easily and the antenna will track it automatically.
1. On homepage, press OK to enter SATELLITE SELECT mode.
3. The antenna will search and track target satellite
automatically.
2. Press UP or DOWN to select your target satellite. Press
OK or wait for 3 seconds when you finished selecting.

KINGSAT Satellite TV Antenna System
20
SETUP MODE
1. SET SAT LIST
You can change the Pre-programmed satellites.
1. On homepage, press RIGHT ►to enter SETUP MODE.
2. Select SET SAT LIST and press OK.
3. Set SAT 1: Select SAT 1 and press OK.
Then you can press LEFT ◄or RIGHT ►and press OK to set
chosen satellite as SAT 1.
4. The method shown above is same for setting SAT 2, SAT 3, SAT
4, SAT 5 and SAT 6.
5. Press LEFT◄to enter save mode.
Press YES to save the input information.
Press NO to cancel and return to SETUP MODE.