EarthQuake SUBZERO-12 User manual

SUBZERO-12
2000 WATTS
Winner of the 2004
Design & Engineering Award
INNOVATIONS
INTERNATIONAL CES
Cut out hole 292mm / 11 1/2"
Mounting
depth
185mm
7 1/4"
127mm
5"
15"
15"
15"
SUBZERO-12"
#1 Sealed design for SPL
Outer dimension shown using 3/4" thick MDF.
Total outer box volume = 1.953 cubic feet.
#2 Sealed design for low frequency extension
Outer dimension shown using 3/4" thick MDF.
Total outer box volume = 2.2 cubic feet.
20.5"
2"
2"
16"
16"
SUBZERO-12"
#4 Bass head design for competition
Outer dimension shown using 3/4" thick MDF.
Total outer box volume = 3.03 cubic feet.
PORT (2"x14.5"x22")
#5 Bandpass design
Outer dimension shown using 3/4" thick MDF.
Total outer box volume = 4.31 cubic feet
18.5"
16.5"
16.5"
SUBZERO-12"
Outer dimension shown using 3/4" thick MDF
Total outer box volume = 2.4 cubic feet.
18"
18"
18"
5"
2” 4”
PORT (2"x16.5"x4”)
16”
16”
13”
18”
SUBZERO-12"
#3 Sealed wedge design for hatch backs or other
tight places.
1” = 2.54 cm
1 cubic foot = 1728 cubic inches
Grille Clearance: 2”
Displacement: .2 Cube Feet
HANDCRAFTED IN USA.
Specifications are subject to change without notice

14"
15”
10 3/4 "
Subzero-12
1” = 2.54 cm
1 cubic foot = 1728 cubic inches
Grille Clearance: 2”
Displacement: .2 Cube Feet
#6 Passive tuned design for deep bass small volume
Outer dimension shown using 3/4" thick MDF.
HANDCRAFTED IN USA.
#7 Sealed design for tight bass
Outer dimension shown using 3/4" thick MDF.
Total outer box volume = 1.306 cubic feet
#9 #10 Port tuned design for deep bass
#8 Sealed down firing design
Bass head design for competition
VB = 2 1/2 ft3
FB = optimized with
SLAPS-12 passive
Drone Tuned Box
Outer dimension shown using 3/4" thick MDF.
Total outer box volume = 2.721 cubic feet
16 1/2"
15”
19" 16"
PORT (3"x12.5"x16") Internal dimensions
Subzero-12
Outer dimension shown using 3/4" thick MDF.
Total outer box volume = 2.309 cubic feet
19"
15”
14” 9"
PORT (2"x12.5"x9") Internal dimensions
Subzero-12
Outer dimension shown using 3/4" thick MDF
Total outer box volume = 2.667 cubic feet
16”
18”
16”
10” 3”
SUBZERO-12"
Specifications are subject to change without notice
SUBZERO-12
2000 WATTS
Winner of the 2004
Design & Engineering Award
INNOVATIONS
INTERNATIONAL CES

HOW TO WIRE / FUSE YOUR
SUBZERO TO AN AMPLIFIER
The Subzero subwoofer
comes equipped with 2
voice coils (dual 2x4
ohms), it can be used in
2, 4 and 8ohm
configurations. The
terminal comes equipped
with fused jumpers, the
voice coil can be easily
configured in series or in
parallel to match the
amplifier in use. It is just a
simple flip of a fuse,
here’s how it works.
PSP (Parallel Series Parallel) Terminal
VC #1
1
- --
S
2
1
2
+ +
PP
DO NOT
USE
VC #2
MONO 2-OHMS
TYPICALAMPLIFIER TERMINAL
2-channel
2-ohm load
(voice coils in parallel)
(using 2 fuses)
8-GAUGE 8-GAUGE
3mm
Hex-nut
cable
fasteners
1
- --
2
1
2
+ +
S
PP
VC #1
VC #2
CH-1 CH-2
TYPICALAMPLIFIER TERMINAL
2-channel
2 x 4-ohm load
(voice coils separated)
(no fuses)
8-GAUGE
8-GAUGE
8-GAUGE 8-GAUGE
1
- --
2
1
2
+ +
DO NOT
USE
S
PP
VC #1
VC #2
MONO 8-OHMS
TYPICALAMPLIFIER TERMINAL
1-channel
8-ohm load
(voice coils in series)
(1 fuse)
8-GAUGE 8-GAUGE
The diagram -on the left side- shows
the PSP terminal in a 2-ohm parallel
configuration (both voice coils are
connected in parallel). Simply place
the 2 fuses in the outer positions in
the fuse placement area. Insert the
negative speaker wire to the far left
insert and one positive to the far right
insert.
This diagram shows the PSP terminal
in a 4-ohm configuration (the two
voice coils are separated). No fuses
are used in this configuration,the voice
coils are powered up separately.
The diagram - on the right side-displays
the PSP in an 8-ohm mode. You will
notice that there is only one fuse in
the center of the fuse placement area.
The voice coils are wired in series.
Insert the negative speaker wire to the
far left insert and one positive to the
far right insert.

Name = EARTHQUAKE Subzero 12 (broken in) Xmax = 31.7500E-3 M
Note = VI MEASURMENTS Krm = 35.5980E-3 Ohm
Model = TSL Erm = 805.0000E-3
Domain = FreeAir Kxm = 237.3670E-3 H
Shape = Round Exm = 672.0000E-3
Profile = Cone Rms = 3.7712 N·S/M
Fmd = 3.0000 KA Mms = 243.5090E-3 Kg
Qmd = 1.0000 Cms = 144.8275E-6 M/N
Flp = 8.0000 KA Vas = 58.1062E-3 M³
Qlp = 2.0000 Fo = 26.8001 Hz
Znom = 8.0000 Ohm Qms = 10.8730
Revc = 7.7000 Ohm Qes = 0.4411
Sd = 53.0000E-3 M² Qts = 0.4239
Mmd = 236.4970E-3 Kg BL = 26.7542 T·M
Pmax = 1.0000E3 W Levc = 13.4777E-3 H
Rtvc = 250.0000E-3 °C/W SPLo = 85.8761 dB
Xgap = 12.7000E-3 M No = 243.1000E-3 %
Xcoil = 76.2000E-3 M
Electro Mechanical Parameters