EAST OAK GFT22001 User manual

BRAZI Fire Pit Table
60000 BTU
Owner’s Manual
MODEL:
GFT22001 | GFT22002 | GFT22003
GFT22004 | GFT22005 | GFT22006
GFT22007 | GFT22008 | GFT22009
This appliance can produce carbon monoxide which has no odor.Using it in an enclosed space can kill you.
Never use this appliance in an enclosed space such as a camper, tent, car, or home.
DANGER FIRE OR EXPLOSION HAZARD
If you smell gas:
.Extinguish any open flame. If odor continues, leave the area immediately.
.After leaving the area, call your gas supplier or fire department.
Failure to follow these instructions could result in fire or explosion, which could cause property damage, personal iniurv.or death.
WARNING: For Outdoor Use Only.
Installation and service must be performed by a qualified installer, service agency, or the gas supplier.
INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this manual for future reference.

1EASTOAK.COM FIRE PIT TABLE
Claim your 3-year warranty
at eastoak.com/warranty
Questions? Comments?
Reach out to us to for expert support!
[email protected]
eastoak.com
1-833-EAST-OAK (USA)
(1-833-327-8625)
eastoak.com
Follow eastoakliving on

2 [email protected]1-833-327-8625
IMPORTANT CAUTION
CAUTION: PLEASE READ ENTIRETY OF MANUAL PRIOR TO ASSEMBLY AND
OPERATION.
Verify all parts and components are present. Check all pieces for any damage
before assembly. If any parts are damaged or missing, contact customer
service at [email protected].
• Some pieces contain sharp edges, which may cause injury or property
damage. To prevent personal injury or damage, please wear protective
gloves during assembly.
• Set power tools setting to the lowest speed possible to prevent any damage.

3EASTOAK.COM FIRE PIT TABLE
CONSUMER
Retain this manual for future reference.
Do not store or use gasoline, or other flammable vapors and liquids,
in the vicinity of this or any other appliance.
An LP-cylinder not connected for use shall not be stored in the vicinity
of this or any other appliance.
255895

4 [email protected]1-833-327-8625

5EASTOAK.COM FIRE PIT TABLE

6 [e-mail]1-833-327-8625
TABLE DIMENSIONS

7EASTOAK.COM FIRE PIT TABLE
PARTS DIAGRAM
size AA BB
44in. 10x 16x
52in. 10x 16x
57in. 10x 16x
B
A
AA BB
I
C
D
E
L
J
FGH

8 SUPPOR[email protected]1-833-327-8625
1This product requires 2 people to assemble.
Before assembly, please read the entirety of this manual to ensure safety
and proper usage. Keep in mind there are a variety of steps.
Place all parts and hardware on a at surface. Inspect each piece and
ensure there is no damage or missing pieces. Please do not destroy or
discard any packaging until there is conrmation that all needed parts are
included for assembly.
Caution: Small components are used in the assembly of this appliance
and may present as a choking hazard. Please keep small children and
pets away during assembly to prevent any injury or death.
Plastic bags and packaging lm may present as a choking or suffocation
hazard. Please keep small children and pets away during assembly to
prevent any injury or death.
Install bracket (L) to panel (D,E) using 2 screws (AA).
ASSEMBLY INSTRUCTIONS
AA
D
E
L
L
2x
1x

9EASTOAK.COM FIRE PIT TABLE
2
3
Assemble the panels (E, F x2, G, H) as shown below
and secure them together using 8 screws (BB).
Place the burner unit on top of the unit.
Fasten screws (BB x 4, I) tightly.
BB
BB
E
FFH
8x
BB
BB
I
4x

10 [email protected]1-833-327-8625
4Secure center piece using 4 screws (BB x4). Align
two screws on the top side. Then, turn the unit upside
down and fasten two screws on the bottom side.
BB
BB
BB
G
4x

11EASTOAK.COM FIRE PIT TABLE
Use the four adjustable leveling
feet to adjust the tabletop
atness. Clockwise for lower
level, counterclockwise for
higher level.
5
The direction of the
front door faces the
direction of the heat
shield
AA 8x
6Place lava or glass rocks into the burner.
ATTENTION:
• Do not put more than 4 lbs of glass rocks or 9 lbs of glass rocks into
the burner.
• Do not touch or arrange the glass rocks once the product is in
use. If arrangement is needed, allow the glass rocks to cool down
completely before doing so.
• Do not mix different types of rocks together.
• Do not put the table lid on the re pit when in use.Ensure the re pit
has cooled before placing the table lid over the re pit.
A
K
Do not lock all the screws at first, and lock
them after all the mounting holes are aligned

LIQUEFIED PETROLEUM GAS (LPG) SAFETY INFORMATION
LPG cylinder used with the product must be:
• Constructed and marked in accordance with the U.S.Department of
Transportation (DOT) specication for LPG cylinder, CAN/CSAB339,
Cylinders, Spheres, and Tubes for the Transportation of Dangerous Goods,
as applicable;
• Arranged for vapor withdrawal.
• Provided with a tank collar to protect the tank valve.
• Provided with a listed overlling prevention device and a QCC I or Type I
(CGA810) LPG cylinder connection.
• Max capacity: 20lbs.
• Max gas supply pressure: 250 PSI (1750 KPa)
• Min.gas supply for input adjustment: 25 PSI (175 KPa)
• Manifold pressure with regulator provided: 11in wc (2.74 KPa)
• Not stored in area with temperature over 125F / 51.5
ASSEMBLY INSTRUCTION
(LPG cylinder)
12 [email protected]1-833-327-8625
The replacement hose assembly shall be that specified by the manufacturer.
•

LPG cylinder connection
ASSEMBLY INSTRUCTION
(LPG cylinder)
• Inspect the entirety of the gasket for any sign of damage or erosion.
Position the LPG cylinder in the repit and secure the unit using the
retainer bolt.
• ATTENTION: Ensure the valve on the re pit and LPG cylinder are set
to the “OFF” position.
• Remove any protective caps on the LPG cylinder. Align the gas lines to
the LPG cylinder nozzle. Fasten the connection with a coupler .
• NOTE: Be mindful of cross threating. To avoid this, do not overtighten
screws and connections. The gas line should be tight enough without any
signs of wiggling or gaps between connections.
• Inspect the gas line and perform a leak test prior to each use (see page 18).
Remember
to tighten!
13EASTOAK.COM FIRE PIT TABLE

LIGHTING INSTRUCTION
• Ensure the re pit control knob is set to the “OFF” position.
• Turn on the gas cylinder valve by pressing the knob and turning it
counterclockwise to the “IGNITOR” position. This is indicated by a lighting
symbol. Repeat this step 2-3 times as needed until burner ignites.
• Once the burner sparks, hold the control knob at the “LOW” position for 20
seconds. The low setting is indicated by “I”. Then, release the knob and turn
it counterclockwise to “HIGH” or “II”. Adjust the ame to your desired level.
NOTE: If the ignitor does not spark or a ame can not hold:
• Ignite the burner with a long lighter or match. Heat-resistant gloves is
highly advised to prevent any damage or injury.
• Press and turn the control knob to the “LOW” or “I” position. Hold for
20 seconds.
• Adjust the ame to your desired level.
• Keep in mind there may be a default 5-minute shut off period before the
burner can be re-ignited.
OPERATION INSTRUCTION
(Turning Off)
• To shut down the unit, turn the control knob clockwise to the “OFF” position.
• Turn off the gas cylinder and disconnect the regulator when appliance is
not in use.
• Allow adequate time for the heater to cool down completely before
transporting it.
Turning OFF
14 [email protected]1-833-327-8625

LPG cylinder disconnection
ASSEMBLY INSTRUCTION
(LPG cylinder)
• Allow unit to completely cool down after use. Then, ensure LPG cylinder
valve is shut and cooled down. Control knob on unit must be in the “OFF”
position.
• Next, turn the coupling nut counterclockwise until the regulator detaches.
• Place the protective cap on the LPG cylinder valve and store the cylinder
in outdoors in a well-ventilated area away from sunlight or excessive heat.
Remember
to loosen!
15EASTOAK.COM FIRE PIT TABLE

16 [email protected]1-833-327-8625
When an appliance is for connection to a fixed piping system, the installation
must conform with local codes, or in the absence of local codes with the
National Fuel Gas Code, ANSI Z223.1 • NFPA 54; National Fuel Gas Code;
Natural Gas and Propane Installation Code, CSA B149.1;
or Propane Storage and Handling Code, CSA B149.2, as applicable;

OPERATION INSTRUCTION
(Leak Check)
2. If there is a leak, disconnect the connection and reconnect,
then perform another leak test.If bubbles continue to appear after
several attempts, you should replace the hose or cylinder valve.
Contact a qualified service technician if attempts to stop the leak(s) are unsuccessful.
Until leak problem is corrected, LPG supply must be shut o ffat the cylinder valve or
the LPG cylinder must be disconnected and removed from the appliance.
Inspect gas hose before use. Hose assembly must be replaced if there is
evidence of excessive abrasion, wear, or damage.
17EASTOAK.COM FIRE PIT TABLE

OPERATION INSTRUCTION
(Ignition)
Before operating the appliance:
• Ensure the gas line is properly connected and there is no holes or damage to
the hose.
• Ensure there are no leaks (see page 18 for how to check for leaks).
• Ensure the LPG cylinder valve and all control knobs are switched to the
“OFF” position.
WARRANTY AND SERVICE
GUARANTEED 3-YEAR WARRANTY
Thank you for choosing East Oak. This product is covered by our company
warranty for up to 3 years from its original purchase date.
CLAIM WARRANTY
If you’d like to claim your product’s warranty, register your new product on our
website at www.eastoak.com/warranty .
18 [email protected]1-833-327-8625