Disposal
Waste electrical products and batteries not be
disposed of with household waste!
Dispose of the waste product via a collec-
tion point for electronic scrap or via your
specialist dealer.
Dispose of used batteries in a recycling
bin for batteries or via the specialist trade.
Put the packaging material into the recy-
cling bins for cardboard, paper and plas-
tics.
Warrant
Within the statutory warranty period we undertake
to rectify free of charge by repair or replacement
any product defects arising from material or pro-
duction faults.
Any unauthorized tampering with, or modications
to, the product shall render this warranty null and
void.
Function Operation
[press the button]
LED view Comment
Set follow-up time in seconds SEC x5 Set follow-up time in 5-second steps (max. 55 s)
1. Button P LEDs W+F light up in accordance
with the default settings
20 s after the nal time you activate the button, there
is automatic break-o
select the
function
2. Button F until the LED SEC x5 lights
set the
value
3. Button W LEDs W0 to W11 light up in ac-
cordance with your selection
in steps of 5 s
(W0 = 1 s, W1 = 5 s, W2 = 10 s ... W11 = 55 s)
4. Button SET selection saved
Set follow-up time in minutes MIN Set follow-up times in minutes from 1 min to 11 min
1. Button P LEDs W+F light up in accordance
with the default settings
20 s after the nal time you activate the button, there
is automatic break-o
select the
function
2. Button F until the LED MIN lights
set the
value
3. Button W LEDs W0 to W11 light up in ac-
cordance with your selection
in steps of 1 min
(W0 = 0 min, W1 = 1 min, W2 = 2 min ... W11 = 11 min)
4. Button SET selection saved
Set time multiplier X The progammed follow-up time (minutes + seconds)
x factor required (1 to 11)
max. time: 11 x (55s+11min) = 131 min (2h+11min)
1. Button P LEDs W+F light up in accordance
with the default settings
20 s after the nal time you activate the button, there
is automatic break-o
select the
function
2. Button F until the LED Xlights
set the
value
3. Button W LEDs W0 to W11 light up in ac-
cordance with your selection
set time x factor required
(W1 = x1, W2 = x2 ... W11= x 11)
4. Button SET selection saved
Enable / disable light sensor If the light sensor is switched o, the motion detector
operates independently of the selected.
1. Button P LEDs W+F light up in accordance
with the default settings
20 s after the nal time you activate the button, there
is automatic break-o
select the
function
2. Button F until the LED lights
3. Button W LED W4 lights: Sensor ON
LED W4 o: Sensor OFF
4. Button SET selection saved
Set brightness threshold Set the brightness value below which the motion
detector should operate
1. Button P LEDs W+F light up in accordance
with the default settings
20 s after the nal time you activate the button, there
is automatic break-o
select the
function
2. Button F until the LED lights LED W, blinking, shows the currently measured
brightness
set the
value
3. Button W LEDs W0 to W11 light up in ac-
cordance with your selection
W0 to W11 = 1 lx to 150 lx
4. Button SET selection saved
Conformity
Hereby, ELDAT GmbH declares that the radio
equipment type RTS40 is in compliance with
Directive 2014/53/EU. The full text of the EU dec-
laration of conformity is available at the following
internet address: www.eldat.de
For use in: EU/CH/FL/IS/N
Service
If, despite correct handling, faults or malfunctions
occur or if the product was damaged, please
contact your retailer or the manufacturer.
ELDAT GmbH
Im Gewerbepark 14
15711 Königs Wusterhausen
Germany
Phone: + 49 (0) 33 75 / 90 37-310
Fax: + 49 (0) 33 75 / 90 37-90
Internet: www.eldat.de
RTS40E5001-01
RTS40E5001-02
PTx
P
PTx
SET
SET ABB
P Programming button
W Button W: set the values or
transmission code A
LEDs W: show selected value
F Button F: select the function or
transmission code B
LEDs F: show selected function
SET Save the chosen settings
only RTS40E5001-02:
Button I Switch load ON (transmission code A)
The motion detector is deactivated.
Button O Switch load OFF (transmission code B)
The motion detector is deactivated.
Button A Automatic operation
The motion detector is activated
(switching delay 5 s)
Switch load OFF (transmission code B)
Activate learning mode on the receiver
With the button PTx you can bring the receiver
into the programming mode.
Condition for this:
- The receiver supports this feature.
- The transmitter has already been program-
med into the receiver.
Then, a new transmitter can be learned into the
receiver. Please read the operating instructions
supplied with the receivers.
Battery check
The transmitter has a battery check function,
which checks the capacity of the battery during
the transmission process.
After ending the transmission process, a low vol-
tage message is sent automatically. This message
can be assessed by suitable Easywave receivers.
Information on this can be found in the instructions
for use associated with the appropriate receiver.
Trouble Shooting
If the radio control does not react to the:
- Exchange the batteries.
- Check that the wireless connection at the
installation site is not impaired between the
transmitter and the receiver.
- Memorize the transmission code in the
receiver.
- Other wireless devices using the same fre-
quency and working in direct proximity may
interfere with the device.
Settings
The factor settings of the RTS40 are as follows:
- The light sensor is deactivated,
- The follow-up time is one second (W=0).
UM104606D 0617 EN
