Eazy2Hd HDMI 4x1 Quad User manual

HDMI 4x1 Quad Multi-Viewer
With Seamless Switcher
Operation Manual
1. Introduction
This product is a high performance 4 by 1 Quad Multi-Viewer with seamless
switcher. It supports four High definition input source display on one screen, and
have three multi-view effect mode. As a switcher, it can also seamlessly switch
the four HD input freely. The product can be controlled by various ways, through
the front panel button control, IR control, RS232 control etc.The product
provides an S/PDIF link to output the HDMI source audio at the same time. In
addition, this product have basic version and extender version. The Extender
version can extend the video and audio signals over single 50m CAT5e/6 with
Bi-directional IR control.
2. Features
1. Compliant with HDMI 1.3a,HDCP 1.2
2. Supports multiplexed HDMI 4-input and 1-output
3. Supports up to 1080p High Definition resolution
4. Support 4 by1 Quad Multi-viewer and seamless switch
5. Support scaler up, scaler down function
6. Support multi output resolution

7. Support digital audio format LPCM/AC3/DTS
8. Support button,IR,RS232 etc various controlled ways
9. IR system allowing for control of source at display end
10. Allows HDMI Audio/Video and IR signals to be transmitted over a single
Cat5e/6 cable(Extender Version).
3. Package Contents
Basic Version
1. 1pcs HDMI Quad Multi-Viewer
2. 1pcs 12V/2.5A DC power adaptor
3. 1pcs Remote Control
4. 1pcs Wide-band IR Receiver
5. 4pcs Wide-band IR Transmitter
6. 1pcs RS232 Cable
7. 1pcs Operation Manual
Extender Version
1. 1pcs HDMI Quad Multi-Viewer
2. 1pcs CAT5e/6 Receiver
3. 1pcs 12V/2.5A DC power adaptor
4. 1pcs 5V/1A DC power adaptor
5. 1pcs Remote Control
6. 2pcs Wide-band IR Receiver
7. 5pcs Wide-band IR Transmitter
8. 1pcs RS232 Cable
9. 1pcs Operation Manual
4. Specification
Video Bandwidth
2.25Gbps
Input Ports
4 ×HDMI (Female type),1x RS232;
Output Ports
1 × HDMI (Female type), 1xRCA, 1xUTP(Extender
version)
Audio output
PCM2, 5.1, 7.1CH, Dolby 5.1, DTS5.1
Input Resolution
480i60Hz,480p60Hz,576i50Hz,576p50Hz,720p50/60Hz,
1080i50/60Hz,1080p24/30/50/60Hz,800x600@60,
1024x768@60,1280x720@60,1920x1080@60;
Output Resolution
1080p,1080i,720p,1024x768,1360x768
ESD Protection
Human Body model: ±8 kV (air-gap discharge)
±4 kV (contact discharge)
Power Supply
12 V/2.5A DC (US/EU standards, CE/FCC/UL certified)
Dimensions
118mm(W) X 250mm (D) X 32mm(H)

Weight
750 g
Chassis Material
Metal
Silkscreen Color
Black
Operating Temperature
0 °C~40 °C/ 32 °F~104 °F
Storage Temperature
−20 °C ~ 60 °C/−4 °F ~140 °F
Relative Humidity
20~90 % RH (non-condensing)
Power Consumption
10 W
5. Operation and Functions
5.1 Front panel
1. ON/OFF: Power on/off switch.
2. SERVICE: For factory use only.
3. IR : Remote control receiver window.
4. POWER LED: This red LED illuminates when the device is connected with
power supply.
5. IN1,2,3,4 LED: These red LED illuminates when the output select to the
corresponding input.
6. INPUT BUTTON: Press this button to select the input source.
7. MODE BUTTON: Press this button to select the multi-view display mode.
※see the detail description below(chapter 5.7).
8. RESO BUTTON: Press this button to select the HDMI output resolution.
5.2 Rear panel (Basic Version)
1. Input: These slot is where you connect the HDMI source output from DVD,
PS3,Set-top Box and Note Book.
2. OUTPUT: The HDMI is where you connect the HDTV or monitor with HDMI
cable for input source display. The Coax is where you connect to the amplifier
with coaxial cable.
3. IR RX: Connect to the IR Receiver for IR signal reception. Ensure that remote
being used is within the direct line-of-sight of the IR receiver.

4. IR TX: Connect the IR Blaster cable included in the package for IR signal
transmission. Pace the IR blaster in direct line-of-sight of the equipment to be
controlled.
5. RS232: Connect the RS232 port to the PC or notebook by RS232 Cable.
6. DC 12V: Plug the 12V DC power supply into the unit and connect the adaptor
to AC wall outlet.
5.3 Rear panel (Extender Version)
1. Input: These slot is where you connect the HDMI source output from DVD,
PS3,Set-top Box and Note Book.
2. OUTPUT: The HDMI is where you connect the HDTV or monitor with HDMI
cable for input source display. The UTP port connect to CAT Receiver by
CAT5e/6 cable for signal extend. The Coax is where you connect to the
amplifier with coaxial cable.
3. IR RX: Connect to the IR Receiver for IR signal reception. Ensure that remote
being used is within the direct line-of-sight of the IR receiver.
4. IR TX: Connect the IR Blaster cable included in the package for IR signal
transmission. Pace the IR blaster in direct line-of-sight of the equipment to be
controlled.
5. RS232: Connect the RS232 port to the PC or notebook by RS232 Cable.
6. DC 12V: Plug the 12V DC power supply into the unit and connect the adaptor
to AC wall outlet.
5.4 CAT Receiver(Extender Version)
①DC 5V: Connect from 5V DC power supply into the unit and connect the
adaptor to an AC outlet.
②IR RX: Connect to the IR Receiver for IR signal reception. Ensure that remote
being used is within the direct line-of-sight of the IR receiver.

③IR TX: Connect the IR Blaster cable included in the package for IR signal
transmission. Pace the IR blaster in direct line-of-sight of the equipment to be
controlled.
④CAT5E/6:Connect the CAT input of the receiver with the CAT output of the
transmitter with CAT5E/6 cable.
⑤HDMI OUT: This slot is to connect the HDMI input port of your display such as
an HDTV.
⑥LOCK LED: This LED will illuminate when the HDMI signal from the
transmitter is stable.
⑦Power LED: This LED will illuminate when the device is connected with
power supply.
⑧Coaxial out: This slot is where you connect to the audio amplifier with coaxial
cable.
⑨ARC : Switch the ARC switcher will open or close the ARC function.
ARC function : If you need use ARC, your HDTV must support this function,
When you open the ARC function, the coaxial of the receiver will output the
HDTV current display content audio signal. Otherwise will output the HDMI
source(DVD, set-top-box ,etc) audio signal.
5.5 Connect and Operate
1. Connect the signal sources such as Blu-Ray Player, Play Station 3,
audio/video receiver, satellite receivers and computers equipped with HDMI
output interfaces with a short high-speed HDMI cable to the HDMI Switcher
inputs.
2. Connect the HDMI output of the HDMI Switcher to a high-definition display
device such as HD-LCD, HD-DLP and HD projectors with HDMI input
interfaces. Use high-speed HDMI cables that are recommended for the
distances that are required for each connection.
3. The Switcher is powered by an external power supply which is included.
Connect power first to the source, then to the Switcher and then to HD TV or
projector.
4. The input source can be controlled from the display. This is accomplished by
using an optional IR Receiver pigtail pointing away from the display(s),
which can be connected with an optional HDMI IR Adapter , and inserted
between HDMI cable connector and display with the toggle switcher at the
“IR” position. The IR Transmitter pigtail is used to connected to the switcher
and pointed to the source(s). The switcher also have a capability of being
controlled via Remote control.
5.6 Wideband IR(30KHz---60KHz) introduction

IR BLASTER (TX)
To control the source:Plug IR Blaster into IR TX port of transmitter unit; place
blaster in front of the IR eye of the source.
IR RECEIVER (RX)
To control the source:Plug IR Receiver into IR RX port of receiver unit; place
receiver at or near display.
5.7 Detail description of display mode
The quad multi-viewer have 3 display modes.
MODE1: The quad multi-viewer divides the four HD input to the same size and
display on one screen. And now switch the input button on front panel or IR
remote, the HDMI output audio will Corresponding to the selected input source.
MODE2: The quad multi-viewer divide the four HD input to one bigger and three

smaller picture display on one screen. And now switch the input button on front
panel or IR remote ,the bigger picture will Corresponding to the selected input
source. The HDMI output audio follow the bigger picture source.
MODE3: The quad multi-viewer will separate display the four HD input, and now
it is a seamless switcher.
6.Remote Control
1. Input select button: press these buttons, the
quad multi-viewer will select the corresponding
input source, the front panel LED will indicate
the selected input source status .
2. Mode select button: press these buttons, the
quad multi-viewer will select the Corresponding
mode, see the detail description(chapter 5.7).
3. Resolution button: press these buttons ,the
HDMI will output different resolution,
1080p,1080i,720p,1024x768,1360x768.
The F1,F2 button expand for user defined
function.
Press the Reset button, the quad multi-viewer
will reset to factory state.
4.Picture button: press these buttons can adjust
the display picture contrast, brightness, color and
sharpness.
7. PC controller user guide
Installation
The PC controller is green software. Just use a cable to connect the PC via
RS232 port and copy “Quad multi-viewer.exe” to PC to complete installation.
Preparation
1. Connect PC and multi-viewer by RS232 cable (headers of both sides of cable
should be FEMALE)
2. Power-up multi-viewer
3. Double click Quad multi-viewer.exe icon to run it

1. Select PC connect COM port，Click to connect or disconnect PC and multi-viewer.
2. Select the HDMI output resolution.
3. Select the input source.
4. Select the output mode, see the detail description(chapter 5.7).
5. Adjust the HDMI output picture quality.
6. Display or hidden the OSD menu.
7. FW upgrade part: Click to open Firmware. the click the upgrade button, the new
firmware will auto download to the multi-viewer and restart it.
8. Press the Reset button, the quad multi-viewer will reset to factory state.
8. Connection Diagram

Basic version:
Extender version: