Starmatrix Clever-Pool/220V Owner's manual

CLEVER-POOL ENERGY SAVER
ACCORDING TO：EN61800-5-1:2007
Designed by STARMATRIX GROUP INC.,
Installation, Operation & Maintanence Instructions
Read this manual carefully before commencing installation
WWW.STARMATRIX.CN
Please leave this instruction booklet with the owner as it contains important maintanence and safty information.
- 1 -

4.1 BUTTON AND FUCNTION EXPLANATION …………………………………………………………………………………13
CONTENTS
1. SAFTY AND CAUTION
1.1 READING BEFORE INSTALLATION………………..………………………………………..…………………………………3
1.2 PRODUCT CHECK BEFORE INSTALLATION ……………..………………………………..………………………………..4
1.3 ENVIROMENT CAUTION ………………………………………………..………………..……………………………………...5
2.1 DIMENSION AND TECHNICAL PARAMETERS………………………………………..………………………………………6
3.1 INSTALLATION ………………………………………..………………………………………………………………………...…7
3.1.1 INSTALLATION SKETCH AND DESCRIPTION………………………………………………………………………….7
3.2 WIRE CONNECTION ……………..……………………………………………………………………………………………… 8
3.2.1 WIRE CONNECTION AND DESCRIPTION FOR 2HP AC220V SINGLE PHASE IN - SINGLE PHASE OUT….….8
3.2.2 WIRE CONNECTION AND DESCRIPTION FOR 3HP AC220V SINGLE PHASE IN - THREE PHASE OUT….….9
3.2.3 WIRE CONNECTION AND DESCRIPTION FOR 5HP AC380V THREE PHASE IN - THREE PHASE OUT….….10
3.3 RUNNING ………………………………………...……………………………………………………………………………. 10
3.3.1 CHECK BEFORE RUNNING………………………………………………………………………………………………10
3.3.2 PROGRAMMING GUIDE …………………………………………………………………………………………………..11
2. PRODUCT DIMENSION AND PARAMETERS
3. INSTALLATION AND FUNCTION EXPLANATION
4. BUTTON AND FUCNTION EXPLANATION
- 2 -

DANGER
1. SAFTY AND CAUTION
1.1 READING BEFORE INSTALLATION
Clever-Pool uses vector frequency technology and is a highly precious electronic device, to ensure for personal and
property safty, please read carefully this instruction before using.
There are marks【DANGER】or【CAUTION】in this book，please strictly obey when moving,installing,using or
checking the product.
1、Please make sure to use the correct power supply.
2、Please make sure to close the control panel before power connection to avoid eletricity shock or
explosion
3、Please make sure not to confuse the input and output terminals.
5、Please DO NOT touch the wire terminals when power is connected.
7、Please DO NOT use wet hands for operation.
6、Please wait after 10 minutes after the power is cut off when all the indication lights are off for further
maintanence.
8、Please ask for professional help if you need to change any parts, strictly forbidden to leave any metal
things inside our Clever-Pool.
4、If our Clever-Pool is stocked over 2 years, please use a voltage adjuster to increase the voltage
gradually when power connection.
- 3 -

CAUTION
3、Power connection is required after control panel closed,electricity shock will occure if against this rule.
9、Please stock our Clever-Pool in a dry,ventilated and cool place.
1.2 PRODUCT CHECK BEFORE INSTALLATION
Each Clever-Pool is 100% tested before factory delivery, you need to check by yourself below:
⑴If our Clever-Pool is the right model you ordered.
⑵Any damage caused by transportation, if yes please do not connect to power supply.
5、Do not disconnect the wire connection if power is connected, serious personal damage will occure if
against this rule.
8、Make sure air ventilation when in summer or high ambient temperature use,this will avoid
condensate water formed and electrical faulty.
1. SAFTY AND CAUTION
1、Installation based on local safty rules.
2、Only professionals for installation and maintanence.
4、Do not touch the terminals,electricity shock will occure if against this rule.
6、Do not touch CMOS elements.
7、No voltage duration test allowed for our Clever-Pool, it will get semiconductor elements damaged.
- 4 -

→No corrosive fluid →No dust or metal scraps
→Away from radioactive or flammable substances →No electromagnetic interference
→No rain drops or wet enviroment
1. SAFTY AND CAUTION
1.3 ENVIROMENT CAUTION
The correct enviroment for our Clever-Pool determines its right function and life. So the installation must obey below:
→Indoor use →Ambient temperature:-10℃～+40℃
→No direct sunshine →No oil or salt
- 5 -

Item Model
Clever-
Pool/220V
Clever-Pool
M/220V
Clever-Pool/380V
Input power Single-phase AC Single-phase AC Three-phase AC
Input voltage 220V±15% 220V±15% 380V±15%
Input frequency 50/60Hz 50/60Hz 50/60Hz
Output voltage
1～220V 3～220V 3～380V
PUMP TYPE SINGLE-PHASE THREE-PHASE THREE-PHASE
Max.Power MAX 2HP MAX 3HP MAX 5HP
Max current 12A 10A 10A
Mode option
Cooling
2. DIMENSION AND PARAMETERS
Motor speed
range
2.1 DIMENSION AND TECHNICAL PARAMETERS
Dimension
PARAMETER SHEET
50Hz:1200～3000rpm
60Hz:1200～3600rpm
Manual or Auto
By air
- 6 -

1. Use a cross screwdriver to take
off the screws as shown 3 and plate 1
3.1 INSTALLATION
3.1.1 INSTALLATION SKETCH AND DESCRIPTION
Sketch for Installation
Procedure and instruction
and use screws as shown 2 to fix
3. INSTALLATION AND FUNCTION EXPLANATION
power supply socket.
6、Strictly follow the operation
steps as indicated in this manual.
2、Put plate 1 in your installation place
plate 1.
3、Put the control box 4 on plate 1
and fix with screws as shown 3
4、Connect the plug from pump to the part
as shown 6.
5、Connect plug 5 as shown to the correct
- 7 -

3.2 WIRE CONNECTION
Wires has been preconnected before factory delivery as per request, if you need to
re-connect the wires, please pay attention as below:
3.2.1 WIRE CONNECTION AND DESCRIPTION FOR 2HP AC220V SINGLE PHASE IN - SINGLE PHASE OUT
WIRE CONNECTION SKETCH
Procedure and instruction
3. INSTALLATION AND FUNCTION EXPLANATION
9.Power supply connected only after the
control panel is fixed,
1.Disconnect power before opening the control panel.
2.Make sure no connection between PE,N,L1 termials and
U,V terminals.
3.Wire connection operated only when power disconnected.
4.Check if the input voltage from the power supply is
compliance with clever-pool.
5.No voltage duration test
6.Screw torque for terminal screws more than 1.7N.m
7.Ground link must be connected before operation.
8.Must use the copper wires over 3G1.5mm2
- 8 -

3. INSTALLATION AND FUNCTION EXPLANATION
3.2.2 WIRE CONNECTION AND DESCRIPTION FOR 3HP AC220V SINGLE PHASE IN - THREE PHASE OUT
WIRE CONNECTION SKETCH
3.Wire connection operated only when power disconnected.
4.Check if the input voltage from the power supply is
compliance with clever-pool.
5.No voltage duration test
6.Screw torque for terminal screws more than 1.7N.m
7.Ground link must be connected before operation.
8.Must use the copper wires over 3G2.0mm2
9.Power supply connected only after the
control panel is fixed,
Procedure and instruction
1.Disconnect power before opening the control panel.
2.Make sure no connection between PE,N,L1 termials and
U,V,W terminals.
- 9 -

8.Must use the copper wires over 4G2.0mm2
9.Power supply connected only after the
control panel is fixed,
2.Check if any metal substances left in the product.
3.Check if wire terminals are well tightened.
4.Check if there are naked wires on the terminals touching other terminals.
3.2.3 WIRE CONNECTION AND DESCRIPTION FOR 5HP AC380V THREE PHASE IN - THREE PHASE OUT
WIRE CONNECTION SKETCH
Procedure and instruction
1.Disconnect power before opening the control panel.
2.Make sure no connection between PE,T,S,R termials and
U,V W terminals.
3.Wire connection operated only when power disconnected.
4.Check if the input voltage from the power supply is
compliance with clever-pool.
5.No voltage duration test
6.Screw torque for terminal screws more than 1.7N.m
7.Ground link must be connected before operation.
3. INSTALLATION AND FUNCTION EXPLANATION
3.3 RUNNING AND OPERATION
3.3.1 BEFORE RUNNING AND OPERATION
1.Check if installation and wire connection is 100% correct.
- 10 -

In stop mode the display will now show MANUAL, LOW RPM and the speed in rpm.
6.A GFCI device must be used in the system.
7.Check if the power supply frequence is the same as CLEVER-POOL, if no please move the dial-switch for option.
8.If all connection is correct,run with no load. If it is a three-phase pump. Please check the motor rotation direction, you
can choose the wire connection between UV,WV or WU, you can also use dial-switch for option.
3.3.2 PROGRAMMING GUIDE
1.The Clever-Pool has two running modes：Manual mode and Auto mode.
5.Check if the contral panel is well closed.
1.1 Manual mode is used when you are connecting to a pool chlorinator or timer. The system time settings are not
required to run in this mode.
1.2 Auto mode is used when there is no chlorinator or timer and includes up to 4 separate timers with individual speed
options.This is ideal for when you want to run your pool pump at different times and speeds to take advantage of the different
electrical consumption.
2. Manual mode
1.3 In stop and manual mode press the SET/RESET button once to switch to Auto Mode. In stop and Auto mode press
the RUN/STOP button to switch to Manual Mode.
3. INSTALLATION AND FUNCTION EXPLANATION
- 11 -

Press the up or down buttons to select the speed. Alternatively press one of the systems, preset speed buttons LOW RPM,
MEDI RPM, HIGH RPM.
Press the RUN/STOP button to put it into run mode, this will start the pump. When the chlorinator timer turns off, the CLEVER-
POOL will store the speed and resume at that speed when switched on again.
To stop the pump simply press the RUN/STOP button again.
3. Back Wash mode
In stop mode press the SET/RESET button once. The display will now show MANUAL, LOW RPM and the speed in rpm.
- 12 -

Press the BACKWASH button. The display will now show backwash and the rpm.
Press the RUN/STOP button to put it into on mode, this will start the pump.
- 13 -

4. Time setting
Press the RUN/STOP button to stop the pump
4.1 Current time
In stop and Auto Mode, Press UP and Down button to set Current time,
Press the SET/RESET button to step over from hours to minutes. The display will then flash the minutes digits.
- 14 -

Press the SET/RESET button to store the time. The display will now show the current time with flashing cursor and the word
now
shown at the top.
4.2 Auto Mode timer and Speed setting
In stop mode press the SET/RESET button, The display should show CURRENT TIME, START TIME, STOP TIME and the
stored
time with hours digits flashing. This is the start time for AUTO MODE 1.
Press the SET/RESET button to step over from hours to minutes and from Start Time to Stop time
Press the up or down button to select the hours.
- 15 -

Press the SET/RESET button to step to SPEED setting. The display will now show the flashing four digits for speed,which is
the speed for AUTO MODE 1.Press the up or down button to change motor speed. Alternatively press one of the systems
preset speed buttons LOW RPM, MEDI RPM, HIGH RPM.
Press the SET/RESET button to store the speed and step over to AUTO MODE 2. The display should show CURRENT
TIME, START TIME, STOP TIME and the stored time with hours digits flashing. This is the start time for AUTO MODE 2.
Repeat steps above to set speed, start and stop times for AUTO MODE 2 3 and 4. Pressing the SET/RESET button
after selecting the speed for Auto mode 4 will finalize the timer settings.
The display will go blank and return to stop mode with the current set time displayed.
- 16 -

Alternatively if you only require one time period per day press the SET/RESET button to cycle through time a speed settings
of the remaining TIMERS ensuring all start and stop times are set to zero's or to the same time period. Please note all
settings for AUTO MODE 1 to 4 will be retained in the event of power loss.
After all timers have been set.The CLEVER-POOL will then start and stop the pump at set times and speeds.
- 17 -

Number Name
1 Power light
2 Pump light
3
Increase
4
Decrease
5
Full RPM
6
High RPM
7
Medium RPM
8
Low RPM
9
LCD screen
10 Setting
11 Run/Stop
Motor rotation
direction
4. BUTTON AND FUCNTION EXPLANATION
Pump motor RPM setting
Pump motor RPM setting
Showing all parameters
Parameter setting or re-set system
Manually control pump run or stop
4.1 BUTTON AND FUCNTION EXPLANATION
Explanation
Power supply connected or disconnected
Pump on or off
Increase the parameter
Decrease the parameter
Pump motor RPM setting
Pump motor RPM setting
Dial-switch S1
Frequency
option
“N” stands for 50Hz
“2” stands for 60Hz
If three-phase motor runs in anti-clockwised
direction, move“O”to“1”
- 18 -