EBIKELING LCD S830 User manual

LCD S830 Manual Control
Panel
User Manual
The Latest Version 2018

1. Exterior Parameters
Casing Material: ABS
Display Material: High Hardness Acrylic (the same
hardness value as tempered glass).
2. Single Supporter
2. Operating Voltage and Connections
a. Operating Voltage: DC36v/48V Compatible (set by the control panel).
b. Connections:
Waterproof Connector Female.
Converter Ring φ22.2mm
1

3. Functions
a. Display
Speed Display, Motor Power Ratio Display, Battery Level Display,
Error Indication, Total Mileage, Single Mileage, Single Running Time
Light Signal
b. Control and Settings
Power Switch, 6km/h Inching Control, Wheel Diameter Setting, Top Speed
Setting, Time Setting for Auto-Hibernation, Backlight Brightness Setting,
Voltage Level Setting
c. Communications Protocol: UART
Display Readings (display at start for 1 second)
3.1 Light
3.2 Battery Level
2

3.3 Multi-Functions Display
Total Mileage: ODO
Single Mileage: TRIP
Single Running Time: Time
Current Voltage VOL
Operating Current: CUR
DST: Unspecified
3.4 Vehicle Power PAS Lever
5 Levers Pedal Assist System
3. 5 Speed Display
Maximum Speed: MAX
Average Speed: AVG
Measuring Unit: MPH or KM/H
The panel will calculate the actual travelling speed based on the wheel diameter
and signal data (number of magnet steel is needed for Hall motors).
3.6 Vehicle Status
6km/h Walk and Push Real-Time Cruise
Low Battery
Controller Failur
Handlebar Failure
Powered Ride
Brake
Motor Failure
3

3.7 Settings
P00: it is Reset all parameter Function:
Change the value as 10, then short press the “M” key, the screen will
Display all segment, then all parameter will reset to the original value
P01: Backlight Brightness (1: darkest; 3: brightest)
P02: Mileage Unit (0: KM; 1: MILE)
P03: Voltage Class: 24V /36V / 48V
P04: Hibernation Time (0: never, other figures refer to the hibernation time)
Unit: Minute
P05: Power Gear – 0/3 Gear Mode: Gear
1/5 Gear Mode: Gear
P06: Wheel Diameter Unit: inch Precision: 0.1
P07: Magnet Steel Number for Speed Test Range: 1-100
P08: Speed Limit
Range: 0-50km/h, parameter 50 indicates no speed limit.
P09: Zero / Non-zero Start Setting:
0: Zero Start
1: Non-zero Start
P10: Drive Mode Setting
0: Power Drive – The specific gear of the assist drive decides the assist power
value. In this status the handlebar does not work.
1: Electric Drive – The vehicle is driven by the handlebar. In this status the power
gear does not work.
2: Power Drive + Electric Drive – Electric drive does not work in zero-startstatus.
P12: Assist Power Intensity Range: 0-5
P13: Power Magnet Steel Number:
P16: ODO Zero-Out: Long press the upper key for 5 seconds and ODO will zero out.
4

4. Keys
Arrangement of keys on the panel:
Introduction of Keys
Key operations involve short press, long press and long press of combination keys.
Short press is used for short/frequent operations as:
1. Short press the UP or Down Button to change assist
power/speed during riding.
2. Short press this key to switch the readings in the multi-function display
section.
Long press on a single key is used to switch mode/on/off status.
Long press on combination keys to set parameters, which can avoid misoperations (short
press on combination keys is disabled, for it’s easy to induce misoperation and hard to
manipulate).
Detailed Instructions
1. Change Assist Power/ Electric Gear In assist power mode
a. Short press assist power +1.
b. Short press assist power -1.
2. Switch Speed Display
Long press + to switch speed display type.
3. Enable / Disable 6km/h cruise, set real-time cruise and turn on/off the lights
When the vehicle is parked, long press to enter 6km/h cruise mode.
When the vehicle is travelling, long press to enter real-time cruise mode.
5

Long press or Press Throttle to exit the cruise mode when the vehicle is in
cruise mode.
Long press to turn on/off backlight
4. Turn on/off the LCD Panel
When the display panel is operating, long press and it will be turn off, oth-
erwise it will be turned on.
5. Switch Displayed Readings in Multi-Functions Section
Short press to switch readings shown in the multi-functions section.
6. Set Parameters
Long press + to enter the setting interface.
Customizable parameters include:
Wheel Diameter (unit: inch);
Magnet Steel Number;
Backlight Brightness;
Low Voltage Threshold (refer to setting: P01-P14)
In the setting interface, short press or to add/minus
value to the parameter, which will blink after modified. After selecting the parameter that
needs to be set,
I. a. Long press to save the current value, and the parameter will stop blinking;
b. Short press to switch to the next parameter and the previously set value will
be saved at the same time.
II. Press + to exit the setting and save the parameters.
Without this operation, the system will automatically exit and save the modified
parameters after 10 seconds.
Note: Due to product upgrade, the product you purchased may be slightly
different from the descriptions in this user manual, and this won’t affect
normal usage.
6