Ebinger EFIS 1 User manual

Operating Instructions
EFIS®1
UNIVERSAL SEARCH MIRROR
www.ebinger.org
Portable Search and Inspection Mirror

2
Trademarks
The Ebinger logo is a registered trademark of Ebinger Prüf- und Ortungstechnik GmbH.
Names of other registered trademarks as follows:
EBEX®| EFIS®| EPAD®| EPAS®| MAGNEX®| MAILEX®| PASSEX®| TREX®
UPEX®| UWEX®
All other trademarks used are the property of their respective registered owners.
Technical specifications
Ebinger retains the right to changes technical specifications at any time without prior notice.
The scope and timing of such changes are at the discretion of the manufacturer. Both
minor and fundamental changes are possible, as part of our programme of continuous
product improvement.
The information presented in this document relates to an entire range of products. The
technical data for individual units can be requested from Ebinger, by quoting the model
name and serial number.
Copyright
© 2012, Ebinger Prüf- und Ortungstechnik GmbH
BA-EFIS1/ 09-12-E-Europe
Unless granted explicit permission, you are prohibited from distributing or reproducing the-
se Operating Instructions, and from utilising or publishing their content. Breach of these
terms will be prosecuted. All rights of registration for potential patents, utility models or
industrial designs reserved. Printed in Germany.
Service address
Ebinger Prüf- und Ortungstechnik GmbH
Technology center Wiesbaum
Vulkanstraße 14
54578 Wiesbaum
Germany
Tel: + 49 6593 99894-0
Fax: + 49 6593 99894-50
Email: [e-mail]
Web: www.ebinger.org

3
TABLE OF CONTENTS
1 General safety guidelines 4
1.1 About these operating instructions 4
1.2 Handling technical faults 5
1.3 Instructions for LEDs 5
1.4 Instructions for disposable or rechargeable batteries 5
1.5 Instructions for cleaning 6
1.6 Usage in professional security work 6
2 Product description 7
2.1 EFIS®– Ebinger vehicle inspection mirror 7
2.2 EFIS®1 Universal search mirror 7
3 Unit components 9
3.1 Components 9
3.2 Identification 9
4 Assembly and component exchange 10
4.1 Replacing the mirror head 10
4.2 Replacing the mirror reflector 10 - 11
4.3 Removing the torch 11
4.4 Changing the torch batteries 12
5 Start-up procedure and operation 13
5.1 Length adjustment of the telescopic handle 13
5.2 Changing the orientation of the mirror head 14
5.3 Using the torch 14
5.4 How to use the search and inspection mirror 15
6 Care and troubleshooting 16
6.1 General equipment care 16
6.2 Troubleshooting 17
7 Accessories and order details 17
7.1 Available spare parts / part numbers 17
7.2 Dimensions 18
7.3 Components / part numbers / weight 19
7.4 Optional accessories 19 - 20
8 Technical data 21

i
!
EFIS®1
4General safety
1. GENERAL SAFETY GUIDELINES
This section presents some important safety guidelines that must be observed must
observe at all times when using the unit.
1.1 About these operating instructions
Important:
Before starting to use this unit, you must read and observe the following safety guide
lines:
➊Read this manual carefully before assembling the unit, and before switching on
and working with the unit!
➋Ensure that you follow the instructions in this manual for all work involving this
unit! EBINGER and EBINGER‘s representatives accept no liability for losses that resulting
from actions or activities that have not been described in this manual.
➌Use the device only for the intended purpose as described in this manual!
Warning notices, precautionary measures, instructions and tips present information of par-
ticular importance for the user and are marked as follows:
WARNING
Warning notices indicate situations that can present health hazards or
endanger life. Instructions in these sections must be followed strictly at
all times!
CAUTION
Precautionary measures relate to situations in which damage to the unit
or consequential damages or loss (e.g. data loss) may occur. Instructions
in these sections must be followed strictly at all times!
ADVICE
Follow the advice given in these sections to avoid faults, which may occur
when operating the unit.
TIP
Follow the advice given in these sections to improve operating.

EFIS®1
5
General safety
1.3 Instructions for LEDs
WARNING
Do not look directly into the LEDs or point the torch into a person‘s eyes!
1.4 Instructions for devices powered by disposable or
rechargeable batteries
WARNING
Batteries and rechargeable batteries can explode if used incorrectly! Always
ensure you follow below the warning notices:
•Use only disposable or rechargeable batteries as specified in the Opera-
ting Instructions.
• When inserting batteries into the device, ensure correct polarity.
• Do not expose batteries to fire or high temperatures.
• Do not attempt to short-circuit, disassemble or recharge disposable dry
batteries.
• In case of short-circuited, rechargeable batteries generate especially high
currents that can cause cable fires, sparks or injury.
• Keep disposable or rechargeable battery contacts dry and avoid short cir-
cuits, do not let them come into contact with conductive materials.
1.2 Handling technical faults
WARNING
Do not continue to use devices with broken connection leads or components
if they are damaged, since this presents a risk of electric shock!
If parts are defective or missing, replace only with original EBINGER spare
parts. Failure to do so may present a risk of short-circuits, overloading, in-
correct polarity or electric shock.
Perform maintenance activities only as described in this manual or as in-
structed during specialist training courses provided by the manufacturer.
iTip
If problems occur, please first read the „Maintenance and Troubleshoo-
ting“ section thoroughly before contacting your local EBINGER Service.

EFIS®1
6General safety
CAUTION
Observe the following safety precautions to avoid damage:
• If the unit is to be stored or not used for a longer period, remove its di-
posable or rechargeable batteries.
• Avoid deep discharge of rechargeable batteries. As resulting damage can-
not be claimed against product warranty.
• Before operating the battery charger, check for correct voltage of mains
supply.
1.5 Instructions for cleaning
CAUTION
Do not use chemical substances to clean the unit. Chemical substances may
react with housing components and cause irreparable damage. For clea-
ning, please use a soft cloth dampened with water.
1.6 Usage in professional security work
WARNING
Any equipment used to support the search for potentially dangerous objects
should be used for such tasks only by personnel who possess the necessary
qualifications according to the applicable international and/or national regu-
lations.
Before deployment in a potentially danger inclined work qualified personnel
must assess and decide on the tactical suitability of the unit.
!ADViCE
Dispose of used disposable and rechargeable batteries only as per appli-
cable local regulatory provisions that apply.

EFIS®1
7
Product description
2. PRODUCT DESCRIPTION
This section informs you about the key properties of this unit and/or of the unit‘s
corresponding product range.
2.1 EFIS®– Ebinger vehicle inspection mirror
Ebinger Prüf- und Ortungstechnik GmbH offers a complete range of search and inspection
mirrors and systems.
The EFIS®– search mirrors let you rapidly inspect areas that are difficult or impossible to
view directly. Our mirrors have a wide range of applications. For example, they can be
used to look under vehicles, packing nets, spaces between or above items of furniture,
as well as in cavities and gaps or areas of buildings hidden from direct view. The mirrors
enable police, customs, military and security personnel to make a much more precise and
thorough search or improve checkpoint processing times. Our inspection mirrors stand out
from the average thanks to their robust, all-weather design.
We have mirrors to fit a wide range of requirements, including:
• Hand held and or wheeled mirror systems
• Torch can be switched on to enable detailed inspection even in low lighting conditions
• Convex mirror designs used to enlarge the field of view
• Video search apparatus using videocamera and colour monitor
2.2 EFIS®1 Universal search mirror
The EFIS®1 – Search mirrors are characterised by the following features:
• Light, rugged and weatherproof
• Illuminates
• Extensible telescopic tube handle
• Range of mirror sizes available (optional)
• Support wheel for large-diameter mirror (optional)
The following special models are available:
• Rectangular mirror head 250 x 150 mm
• Rectangular mirror head 310 x 220 mm, (wheeled)
• Halo mirror head Ø 305 mm, (wheeled)
• Rugged mirror plate in polished stainless steel

EFIS®1
8
Our mirrors have a wide range of application. They support the inspection of the under-
side of vehicles, packing nets, spaces between or above items of furniture, as well as ca-
vities and gaps or areas of buildings hidden from direct view. This allows a significantly
better and thorough search, plus complete handling of inspection points.
The lightweight yet rugged design of the portable EFIS®1, is a versatile tool in a wide ran-
ge of applications not last due to its long, stepless extendable handle, the freely adjustable
mirror and the illumination. The mirror‘s illumination ensures a detailed inspection even
under low light conditions, while the mirror‘s slightly convex mirror plate increases the
field of view.
Product description

EFIS®1
9
Unit components
3. UNIT COMPONENTS
This section informs you about the components of the EFIS®1 inspection mirror, and
the features to unambiguously identify the unit.
3.1 Components
The EFIS®1 Search and Inspection Mirror consists of the following components:
➊Mirror head (185 x 135 mm) with edge protection and knurled nuts
➋Telescopic handle (2 x100 cm) with cover, torch bracket and locking mechanism
➌Premium LED torch
3.2 Identification
Information about the unit type and serial number, as well as any customer-specific refe-
rence codes, can be found at the following location:
•Marking showing type and serial no. on the telescopic tube
Battery operation:
2 x D-cell, (HR 20 type)
Rech. battery operation:
2 x D-cell 1.2 V (HR 20 type, rech.)
➋
Identification point for EFIS®1 Search and Inspection Mirror
EFIS®1 components
➌➊
•Operating instructions (not shown)

EFIS®1
10 Assembly
4. ASSEMBLY AND COMPONENT EXCHANGE
As supplied, the EFIS®1 search mirror is already partly assembled. The section pro-
vides you with information on how to change the mirror head and the torch (e.g.
to change its batteries).
!ADViCE
Before assembling components and parts, inspect these to ensure they are
clean, undamaged and complete.
4.1 Replacing the mirror head
1. Loosen the knurled nut on the mirror by turning it anticlockwise and then slide the
mirror head from its bracket.
2. Slide the new mirror head onto the mirror bracket.
3. Now re-tighten the knurled nut by turning them clockwise.
4.2 Replacing the mirror reflector
1. Hold the mirror firmly as you remove the rim protection on the mirror head.
2. Now replace the reflector.
3. Fit mirror back in place by pushing onto the rim protection.
Replacing the mirror head