Ecco Vantage 12 Series User manual

920-0335-00 Rev. A Page 1 of 3
Installation and Operation Instructions
12 Series Vantage™ Controller
WARNING!
Failure to install or use this product according to manufacturer’s recommendations may result in property
damage, serious bodily/personal injury, and/or death to you and those you are seeking to protect!
!
Do not install and/or operate this safety product unless you have read and understand the safety
information contained in this manual.
1. Proper installation combined with operator training in the use, care and maintenance of emergency warning devices are essential to
ensure the safety of emergency personnel and the public.
2. Emergency warning devices often require high electrical voltages and/or currents. Exercise caution when working with live electrical
connections.
3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high current
arcing, which can cause personal injury and/or severe vehicle damage, including re.
4. Proper placement and installation is vital to the performance of this warning device. Install this product so that output performance of
the system is maximized and the controls are placed within convenient reach of the operator so that s/he can operate the system
without losing eye contact with the roadway.
5. It is the responsibility of the vehicle operator to ensure daily that all features of this product work correctly. In use, the vehicle operator
should ensure the projection of the warning signal is not blocked by vehicle components (i.e., open trunks or compartment doors),
people, vehicles or other obstructions.
6. The use of this or any other warning device does not ensure all drivers can or will observe or react to an emergency warning signal.
Never take the right-of-way for granted. It is your responsibility to be sure you can proceed safely before entering an intersection, drive
against trafc, respond at a high rate of speed, or walk on or around trafc lanes.
7. This equipment is intended for use by authorized personnel only. The user is responsible for understanding and obeying all laws
regarding emergency warning devices. Therefore, the user should check all applicable city, state, and federal laws and regulations.
The manufacturer assumes no liability for any loss resulting from the use of this warning device.
8. This product may contain high intensity LEDs staring directly into these lights could result in temporary and/or permanent vision
impairment.
Caution:
When drilling into any vehicle surface, make sure that the area is free from any electrical wires, fuel lines, vehicle upholstery, vehicle
support members, etc. that could be damaged.
!
12-SERIES LIGHTBAR
BLK
Power Cable
Control Cable
S/T/T Cable
(Brown) Tail
(Yellow) Left
(Green) Right
(White) Ground
(Red) N/C
Adapter
Controller
Pattern 1 (Brown)
Pattern 2 (Orange)
Alley Left (Yellow)
Alley Right (Green)
Worklight (Blue)
Pattern Sel (Violet)
Batt +
2A Mom
OR
RED
25A
Ignition
Switch
(Supplied)
(Optional)

920-0335-00 Rev. A Page 2 of 3
Controller Keypad (EZ0006)
The optional in-cab controller provides convenient control of the Lightbar’s 25
built-in ash patterns and features soft touch buttons and LED function indicator
lights. The EZ0006 Keypad controller is designed for easy installation. Simply
unplug the adapter from the control cable and plug in the controller.
Operation
The 12 series controller consists of 7 buttons with 5 features, and 6 indicator windows. When a feature button is selected, the corresponding
clear indicator(s) will illuminate. Pressing any of the 5 feature buttons will turn that corresponding feature on, pressing it again will turn it off.
There are two large ash pattern preset buttons; only one can be selected at a time. If one is on while the other is selected, it will shut the
previous one off. The “OFF and “SEL” buttons do not have illuminated indicators.
“OFF” - Turns the whole bar off. This is a quick way to shut everything down. Features can also be shut down individually by
pushing the feature’s button.
“Power 1, Power 2” - Turns on the ashing modules with whatever ash pattern was stored to this button.
“AL” - Turns on left alley light, or as custom congured.
“AR” - Turns on right alley light, or as custom congured.
“WL” - Turns on center pair of takedown or worklights, or as custom congured.
“SEL” - Advances to the next ash pattern whenever either power button is selected.
Control Pad Mounting:
To mount the control pad with Velcro, separate the two circu-
lar halves, remove the backing and adhere one piece on the
vehicle dashboard and adhere the other to the back of the con-
troller. To mount the control pad using the swivel mount, rst
mount the swivel unit to the dashboard with either the supplied
screws (note, the suction cup will not work after drilling screws
through the swivel base) or by turning the lever at the base of
the swivel unit to engage the suction cup. Push the controller
onto swivel slide and press the control pad down onto the slide
until it engages the slot in the control pad. (You may need to
turn the controller clockwise once engaged with the slide to
tighten it.) Turn the dial on the swivel head to tighten it against
the back of the control pad. Finally, loosen the hand screw on
the swivel neck to adjust the angle of the control pad. Hold the
pad in the desired position while tightening the hand screw on
the swivel neck.
Push the controller onto swivel slide and press
the control pad down onto the slide until it
engages the slot in the control pad.

920-0335-00 Rev. A Page 3 of 3
Manufacturer Limited Warranty and Limitation of Liability:
Manufacturer warrants that on the date of purchase this product will conform to Manufacturer’s specications for this product (which are available
from the Manufacturer upon request), and Manufacturer further warrants that this product is free from defects in materials and workmanship. This
Limited Warranty extends for Thirty-Six (36) months from the date of purchase. Other warranties may apply, call Manufacturer for details. Manufac-
turer will, at its discretion, repair or replace any product found by the Manufacturer to be defective and subject to this Limited Warranty.
DAMAGE TO PARTS OR PRODUCTS RESULTING FROM TAMPERING, ACCIDENT, ABUSE, MISUSE, NEGLIGENCE, UNAPPROVED MODIFICA-
TIONS, FIRE OR OTHER HAZARD; IMPROPER INSTALLATION OR OPERATION; OR NOT BEING MAINTAINED IN ACCORDANCE WITH THE MAIN-
TENANCE PROCEDURES SET FORTH IN MANUFACTURER’S INSTALLATION AND OPERATING INSTRUCTIONS VOIDS THIS LIMITED WARRANTY.
ORAL STATEMENTS OR REPRESENTATIONS ABOUT THE PRODUCT WHICH MAY HAVE BEEN MADE BY SALESPEOPLE, DEALERS, AGENTS OR
OTHER MANUFACTURER’S REPRESENTATIVES DO NOT CONSTITUTE WARRANTIES. THIS LIMITED WARRANTY MAY NOT BE AMENDED, MODI-
FIED, OR ENLARGED EXCEPT BY A WRITTEN AGREEMENT SIGNED BY AN AUTHORIZED OFFICIAL OF MANUFACTURER WHICH EXPRESSLY
REFERS TO THIS LIMITED WARRANTY.
Exclusion of Other Warranties:
MANUFACTURER MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. THE IMPLIED WARRANTIES FOR MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED AND SHALL NOT APPLY TO THE PRODUCT. BUYER’S SOLE AND EXCLUSIVE REMEDY
IN CONTRACT, TORT, OR UNDER ANY OTHER THEORY AGAINST MANUFACTURER REGARDING THE PRODUCT AND ITS USE SHALL BE THE
REPLACEMENT OR REPAIR OF THE PRODUCT AS DESCRIBED ABOVE.
Limitation of Liability:
IN THE EVENT OF LIABILITY FOR DAMAGES ARISING OUT OF THIS LIMITED WARRANTY OR ANY OTHER CLAIM RELATED TO THE MANU-
FACTURER’S PRODUCTS, MANUFACTURER’S LIABILITY FOR DAMAGES SHALL BE LIMITED TO THE AMOUNT PAID FOR THE PRODUCT AT
THE TIME OF THE ORIGINAL PURCHASE. IN NO EVENT SHALL MANUFACTURER BE LIABLE FOR LOST PROFITS, THE COST OF SUBSTITUTE
EQUIPMENT OR LABOR, PROPERTY DAMAGE, OR OTHER SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES BASED UPON ANY CLAIM
FOR BREACH OF CONTRACT, IMPROPER INSTALLATION, NEGLIGENCE, OR OTHER CLAIM, EVEN IF MANUFACTURER OR A MANUFACTURER’S
REPRESENTATIVE HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. MANUFACTURER SHALL HAVE NO FURTHER OBLIGATION
OR LIABILITY WITH RESPECT TO THE PRODUCT OR ITS SALE, OPERATION AND USE, AND MANUFACTURER NEITHER ASSUMES NOR AUTHO-
RIZES THE ASSUMPTION OF ANY OTHER OBLIGATION OR LIABILITY IN CONNECTION WITH SUCH PRODUCT.
This Limited Warranty denes specic legal rights. You may have other legal rights which vary from state to state. Some states do not allow the
exclusion or limitation of incidental or consequential damages.
833 West Diamond St
Boise, Idaho 83705
Customer Service
USA 800-635-5900
UK [phone]
AUS [phone]
www.eccogroup.com
©2013 ECCO
NOTE: Operating the vehicle without the outter lens installed on the product may result in damage that will NOT be
covered under the warranty.
!