Echo 99944100010 User manual

RAIN GUTTER KIT
99944100010
INSTRUCTIONS
RAIN
GUTTER
CLEAN-OUT
KIT
Blows leaves, pine needles and other debris
from your rain gutters with a powerful blast
of air from your backpack or hand held
ECHO Power Blower.
ECHO, INCORPORATED
400 OAKWOOD ROAD
LAKE ZURICH, IL 60047
www.echo-usa.com
X750002373
06/11
CopyRight© 2011 By Echo, Incorporated All Rights Reserved.
X7501131403

2
RAIN GUTTER KIT
99944100010
FOR MODELS: PB-200, 201, 2100, 230LN, 231LN, 24LN, 2400
A
A
22
3
1
22
3
11
22
3
11
B
22
3
1
1
FOR MODELS: PB-210, 210E, 211
FOR MODELS: PB-46LN, 46HT, 60HT, 400E, 403, 410, 411, 413, 460LN, 461LN, 600 TO S/N 505400, 601 TO
S/N 505600, 6000, 260L, 261L
1
KEY PART NUMBER QTY DESCRIPTION REMARKS
1 21041304260 2 Clamp
2 21001504260 2 Straight Pipe
3 21002304260 2 Elbow Nozzle
A 21002004260 1 Adapter
B 21002003460 1 Adapter
TO SECOND
BLOWER PIPE
ON UNIT
FOR MODELS: PB-600 S/N 505401 & UP, PB-601 S/N 506001 & UP, PB-602, 603, 610, 611

3
ASSEMBLY INSTRUCTIONS
1. Connect 2 long tubes (2) as shown in Fig. 1. Secure tubes
with clamp.
2. Connect 2 elbows (3) that make up adjustable nozzle. Fig.
2.
3. Install the adjustable nozzle to the small end of extension
tube as shown in Fig. 3.
4. Connect slotted end of straight pipe (2) to blower models as
follows:
• ModelsPB-210,210E,211:Connectslottedendofstraight
pipe (2) directly to blower housing. See Fig. 4.
• ModelsPB-46LN,46HT,60HT,400E,403,460LN,461LN,
260L, 261L, 600 TO S/N 505400, 601 TO S/N 505600, 6000
: Connect slotted end of pipe (2) to adapter (B). Connect
adapter (B) to blower swivel pipe.
• ModelsPB-200,201,2100,230LN,231LN,24LN,2400:
Connect adapter (A) to unit then connect kit to adapter with
clamp (1). See Fig. 5.
• ModelsPB-600S/N505401&UP,PB-601S/N506001&
UP, PB-602, 603, 610, 611: Connect adapter (A) to second
blower unit pipe then connect kit pipes to adapter with clamp
(1).
NOTE
Use only enough pipes to comfortably reach the inside of
the gutter.
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
TO BLOWER
HOUSING
2
1
33
2
A1

4
OPERATING INSTRUCTIONS
1. For best results, angle pipes approximately 10 degrees
from the side of the rain gutter. The adjustable nozzle
should be angled 30 to 45 degrees in the direction you will
be cleaning. See Fig. 6.
2. Start the unit and slide the nozzle along the lip of the
gutter, (See Fig. 7) lifting the outlet nozzle up and over
the gutter support brackets. Keep the long pipes angled
slightly ahead of you in the direction you are cleaning. See
Fig. 8.
NOTE
When the power blower is started, the air exiting from the
nozzle will cause the long extension to sway slightly. Hold
theunitrmlyforeffectivecleaning.
Individual conditions will vary when using this attachment.
Somepracticeandexperimentationwillbenecessarytond
the best and most effective position for the type of house and
gutter design.
Fig. 6
Fig. 7
Fig. 8
SAFETY INSTRUCTIONS
WARNING
The operation of any power tool can result in foreign objects being thrown into the eyes, which can result
in severe eye damage. Always wear safety goggles before commencing power tool operation. (These
goggles meet ANSI Standard Z-87.1.)
• DO NOT operate blower and attachments when fatigued.
• DO NOT overreach or stand on unstable support, keep good footing and balance at all times.
• Neverdirectairowtowardsbystanders.Alwaysbeawareofdirectionthedebriswillbethrown.
• Wearearprotectionwheneverpossible.
• Alwaysuseafaceltermasktoavoidbreathingdust.
• DO NOT block gutter nozzle in order to avoid engine damage due to over speed.
• FollowallsafetyinstructionsasoutlineinyoupowerblowersOperator’sManual.