Echo PE-2000 Type 1 User manual

POWER EDGER
OPERATOR'SMANUAL 1
PowerEdger
Operator'sManual
MODELS PE-2000 Type 1/1E
Serial Number 001001 & Up
PE-2000 Type 2E
Serial Number 508036 & Up
WARNING DANGER
Read rules for safe operation and instructions carefully. ECHO provides an Operator's Manual
and a Safety Manual. Both must be read and understood for proper and safe operation.
WARNING
The engine exhaust from this
product contains chemicals known
to the State of California to cause
cancer, birth defects or other
reproductive harm.
PE-2400 Type 1/1E
Serial Number 001001 & Up
PE-3100 Type 1/1E
Serial Number 001001 & Up
89869555332
12/98
X7532271103

2
INTRODUCTION
Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-job-
dependability. Read and understand this manual and the SAFETY MANUAL you found in the same package. You will
find both easy to use and full of helpful operations tips and SAFETY messages.
WARNING DANGER
Read rules for safe operation and instructions carefully. ECHO provides an Operator's Manual and a Safety
Manual. Both must be read and understood for proper and safe operation.
THE OPERATOR'SMANUAL —
contains specifications and information for operation, starting,
stopping, maintenance, storage and assembly specific to this
product.
THE SAFETY MANUAL —
explains possible hazards involved with the use of Edgers and the
measures you should take to make their use safer.
TABLE OF CONTENTS
Introduction ...............................................................2
-The Operator's Manual .............................................. 2
- The Safety Manual ..................................................... 2
ManualSafety Symbols&Important Information .....3
Safety .........................................................................3
- GeneralDescription .............................................3
- Decals..................................................................4
- InternationalSymbols .........................................4
- Equipment ...........................................................5
- Fuel .....................................................................5
- PersonalCondition& SafetyEquipment.............6
- SafeOperation.....................................................7
- ExtendedOperation/ExtremeConditions.............8
Description ................................................................9
- EmissionControl .................................................9
- Contents..............................................................9
Specifications........................................................... 12
Assembly ................................................................. 13
- DriveShaft/PowerHead .................................... 13
- ThrottleCable.................................................... 13
- LoopHandle...................................................... 14
Pre-Operation ........................................................... 15
- Fuel ................................................................... 15
Operation ................................................................. 16
- StartingColdEngine ......................................... 16
- StartingWarmEngine ....................................... 17
- Stopping Engine................................................ 18
- Operating Techniques....................................... 18
Maintenance ............................................................ 19
- SkillLevels ........................................................ 19
- Maintenance Intervals ...................................... 20
- Airfilter ............................................................. 21
- FuelFilter .......................................................... 21
- SparkPlug ......................................................... 22
- CoolingSystem ................................................. 22
- ExhaustSystem ................................................. 23
- MufflerScreen................................................... 23
- CarburetorAdjustmentEmission ...................... 24
- Carburetor Adjustment Non Emission .............. 25
- Lubrication ........................................................ 26
Troubleshooting ...................................................... 27
Storage..................................................................... 28
ServicingInformation............................................... 30
- Parts .................................................................. 30
- Service............................................................... 30
- Warranty Card................................................... 30
- Additional or Replacement Manuals................. 30
- Manual Ordering Instructions........................... 30
Specifications, descriptions and illustrative material in this
literature are as accurate as known at the time of publica-
tion, but are subject to change without notice. Illustrations
may include optional equipment and accessories, and may
not include all standard equipment.

POWER EDGER
OPERATOR'SMANUAL 3
MANUAL SAFETY SYMBOLS & IMPORTANT INFORMATION
Throughout this manual and on the product itself, you will find safety
alerts and helpful, information messages preceded by symbols or key
words. The following is an explanation of those symbols and key words
and what they mean to you.
IMPORTANT
The enclosed message provides
information necessary for the protection
of the unit.
NOTE
This enclosed message provides tips for
use, care and maintenance of the unit.
The circle with the slash symbol means whatever is shown
within the circle is prohibited.
This symbol accompanied by the words WARNING and
DANGER calls attention to an act or condition that can lead to
serious personal injury to operator and bystanders.
SAFETY
GENERAL DESCRIPTION
IMPORTANT
See Description and Specification sections for full description and illustration of model variation in power
head, and handle type.
EDGER
BLADE
GUARD
W/DECAL
SAFETY
DECAL
FRONT
HANDLE
POWER
HEAD
THROTTLE
TRIGGER
DRIVE SHAFT
HOUSING
DEPTH
WHEEL

4
WARNING DANGER
Thisunitcanbedangerousandcauseserious
injuryifimproperlyused.toreduceinjuryrisk
to operator, helpers and bystanders, read
and understand the Operator's and Safety
Manuals, which are provided in Spanish.
INTERNATIONAL SYMBOLS
Symbol
description/application Symbol form/shape Symbol
description/application
Symbol form/shape
Hot
Surface
Carburetor adjustment
- Idle speed
Carburetor adjustment
- High speed mixture
Symbol
description/application Symbol form/shape Symbol
description/application
Symbol form/shape
"WARNING, See
Operator's Manual"
Wear eyes, ears and
head protection
Emergency stop
Fuel and oil mixture
Finger Severing
Carburetor adjustment
- Low speed mixture
DECALS
Locate these safety decals on your unit. The complete unit illustration found in the "DESCRIPTION" section, will help
you locate them. Make sure the decals are legible and that you understand and follow the instructions on them. If a decal
cannot be read, a new one can be ordered from your ECHO Dealer. See PARTS ORDERING instructions for specific
information.
These decals are in English only:
Shaft Decal Guard Decal
Shaft Decal
Spanish Decal English Translation
Esta unidad puede ser peligrosa y producir lesiones
personalesgravessinoseusaenformaadecuada.Para
reducir el riesgo de lesionarse, los operadores, los
ayudantes y los espectadores deben leer y comprender
elManualDelOperadorylosManualesDeSeguridadque
seentreganescritos en español.
ADVERTENCIA PELIGRO
89017740630

POWER EDGER
OPERATOR'SMANUAL 5
FUEL
WARNING DANGER
Fuel is VERY flammable. Use extreme care when mixing, storing
or handling or serious personal injury may result.
•Use an approved fuel container.
•DO NOT smoke near fuel.
•DO NOT allow flames or sparks near fuel.
•Fuel tanks/cans may be under pressure. Always loosen fuel
caps slowly allowing pressure to equalize.
•NEVER refuel a unit when the engine is HOT!
•NEVER refuel a unit with the engine running.
•DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks
outdoors over bare ground.
•Securely tighten fuel cap after refueling.
•Inspect for fuel leakage. If fuel leakage is found, do not start or
operate unit until leakage is repaired.
EQUIPMENTEQUIPMENT
EQUIPMENTEQUIPMENT
EQUIPMENT
Before operation a complete check of the unit must be performed;
•Check unit for loose/missing nuts, bolts and screws. Tighten and/or
replace as needed.
•Inspect fuel lines, tank and area around carburetor for fuel leaks. DO
NOT operate unit if leaks are found.
•Inspect shield for damage and is securely in place. Replace if shield
is damaged or missing.
•Check that the cutting attachment is firmly attached and in safe
operating condition.
•Check that front handle is adjusted for safe, comfortable operation.
See Assembly for proper adjustment.
Spark Arrestor Muffler
The spark arrestor muffler controls the exhaust noise and prevents hot,
glowing particles of carbon from leaving the muffler. Make sure the
spark arrestor screen is in good repair and properly seated in the
muffler.(RefertoExhaustSystemMaintenancepg.23.)
Parts
• Do not use edger if any part is missing or damaged.
• Have repairs done only by an authorized ECHO Service dealer.
• Do not use any attachment, accessory or replacement part unless it
is recommended in this Operator's Manual.
WARNING DANGER
• Use only ECHO approved attachments. Serious injury may result
from the use of a non approved attachment combination. Read
and comply with all safety instructions listed in this manual and
safety manual.
• ECHO,INC. willnot beresponsiblefor thefailure ofcutting
devices, attachments or accessories which have not been tested
and approved by ECHO.
ATTACHMENTS
AND
ACCESSORIES

6
PERSONAL CONDITION &SAFETY EQUIPMENT
WARNING DANGER
Edger users risk injury to themselves and others if the edger is used improperly and or safety precautions are not
followed. Proper clothing and safety gear must be worn when operating a edger.
Eye Protection —
Wear eye protection that meetsANSI Z87.1 or CE requirements
whenever you operate the edger.
Physical Condition —
Your judgment and physical dexterity may not be good:
•if you are sick,
•ifyou are takingmedication,
•if you have taken alcohol or drugs.
Operate unit only if you are physically and mentally well.
Hearing Protection —
Wear hearing protection. OSHA requires the use of hearing protection if
this unit is used 2 hours per day or more. ECHO recommends wearing
hearing protection whenever unit is used.
Hand Protection —
Wear no-slip, heavy duty work gloves to improve your grip on the
edger handles. Gloves also reduce the transmission of machine vibra-
tion to your hands. Special vibration reducing gloves such as Echo's
Pro-Comfort are designed to provide additional comfort.
Proper Clothing —
Wear snug fitting, durable clothing;
•Pants should have long legs, shirts with long sleeves.
•DONOTWEARSHORTS,
•DONOTWEARTIES,SCARFS,JEWELRY.
Wear sturdy work shoes with non-skid soles;
•DONOTWEAROPENTOEDSHOES,
•DONOTOPERATEUNITBAREFOOTED.
10'MINIMUM
After Refueling;
•Wipe any spilled fuel from the unit.
•Move at least 10 ft. (3 M) from refueling location before starting.
After use;
•DO NOT store a unit with fuel in its tank. Leaks can occur. Return
unused fuel to an approved fuel storage container.

POWER EDGER
OPERATOR'SMANUAL 7
Hot Humid Weather --
Heavy protective clothing can increase operator fatigue which may lead
to heat stroke. Schedule heavy work for early morning or late afternoon
hours when temperatures are cooler
SAFE OPERATION
Determine Operation Area
• Review the area to be edged. Look for hazards that could contribute
to unsafe conditions.
• Spectators and fellow workers must be warned, and children and
animalsprevented fromcomingnearer than50ft. (15M)while the
edger is in use.
• Provide all operators of this equipment with the Operator's Manual
and instructions for safe operation.
Operation
UseProperClothing&Equipment
•Before starting the unit, equip yourself and any other person
workingwithin the 50ft. (15M) SafetyZone withthe required
Protective Equipment and clothing.
AvoidHotSurfaces
•During operation, the complete unit, especially the drive shaft
housing, power head, muffler area and gear box may become very
hot, too hot to touch. Avoid contact during and immediately after
operation.
KeepAFirmGrip
- Hold the front and center or rear and center handles with both
hands with thumbs and fingers tightly encircling the handles
KeepASolidStance
•Maintain footing and balance at all times. Do not stand on slippery,
uneven or unstable surfaces. Do not work in odd positions or on
ladders. Do not over reach.

8
EXTENDED OPERATION/EXTREME CONDITIONS
Vibration and Cold
It is believed that a condition called Raynaud’s Phenomenon, which
affects the fingers of certain individuals may be brought about by
exposure to vibration and cold. Exposure to vibration and cold may
cause tingling and burning sensations followed by loss of color and
numbness in the fingers. The following precautions are strongly
recommended because the minimum exposure which might trigger the
ailment is unknown.
•Keep your body warm, especially the head, neck, feet, ankles,
hands and wrists.
•Maintain good blood circulation by performing vigorous arm
exercises during frequent work breaks and also by not smoking.
•Limit the hours of operation. Try to fill each day with jobs where
operating the edger or other hand-held power equipment is not
required.
•If you experience discomfort, redness and swelling of the fingers
followed by whitening and loss of feeling, consult your physician
before further exposing yourself to cold and vibration.
Repetitive Stress Injuries
It is believed that overusing the muscles and tendons of the fingers,
hands, arms and shoulders may cause soreness, swelling, numbness,
weakness and extreme pain in those areas. Certain repetitive hand
activities may put you at a high risk for developing a Repetitive Stress
Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome
(CTS), which could occur when your wrist swells and squeezes a vital
nerve that runs through the area. Some believe that prolonged expo-
sure to vibration may contribute to CTS. CTS can cause severe pain
for months or even years. To reduce the risk of RSI/CTS, do the
following:
•Avoid using your wrist in a bent, extended or twisted position.
Instead try to maintain a straight wrist position. Also, when
grasping, use your whole hand, not just the thumb and index
finger.
•Take periodic breaks to minimize repetition and rest your hands.
•Reduce the speed & force in which you do the repetitive movement.
•Do exercises to strengthen the hand and arm muscles.
•See a doctor if you feel tingling, numbness or pain in the fingers,
hands, wrists or arms. The sooner RSI/CTS is diagnosed, the more
likely permanent nerve and muscle damage can be prevented.

POWER EDGER
OPERATOR'SMANUAL 9
13
15
16
17
19
PE-2000
DESCRIPTION
EMISSION CONTROL
The emission control system for this engine is EM (Engine
Modification).
An Emission Control Label is located on the engine. (This is an
EXAMPLE ONLY, information on label varies by engine
FAMILY).
IMPORTANT ENGINE INFORMATION
ENGINE FAMILY: TEH024UB24RC
DISPLACEMENT: 23.6 CC
THIS ENGINE MEETS U.S. EPA PH1 AND
1996 - 1998 CALIFORNIA EMISSION
REGULATIONS FOR ULGE ENGINES.
REFER TO OWNER'S MANUAL FOR
MAINTENANCE SPECIFICATIONS AND
ADJUSTMENTS.
KIORITZ CORP.
The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions,
shield installation and positioning of the front handle are necessary.
After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing
parts. Use the contents list to check for missing parts.
CONTENTS
__ 1, Edger Assembly
__ 1,PowerHead
__ 1,Drive Shaft Assembly
__ 1,PlasticBag(Co-Pack)
__ 1, Operators Manual
__ 1, Safety Manual
__ 1, Warranty Registration Card
__ 1,ECHOEmissions andWarrantyStatement
__ 1,50:11Gal.ECHOOilMix
__ 1,Front Handle
__ 2,bolt5x40mm
__ 2, nut 5
__ 1, split pin
__ 1,LockingTool
__ 1,10mmSpannerWrench
__ Safety Glasses
1
14
18
20
21
22
23
4
5
6
7
10
11
12
8
9
__1,Scrench(CombinationSparkPlugSocket/Screwdriver

10
C
PE-2400
PE-3100
CONTENTS
__ 1, Edger Assembly
__ 1,PowerHead
__ 1,Drive Shaft Assembly
__ 1,PlasticBag(Co-Pack)
__ 1, Operators Manual
__ 1, Safety Manual
__ 1, Warranty Registration Card
__ 1, ECHOEmissions andWarrantyStatement
__ 1, 50:11Gal.ECHOOilMix
__ 1,Front Handle
__ 4,5X35mmscrews
__ 4,5mmnuts
__ 1,Scrench(CombinationSparkPlugSocket/Screwdriver
__ 1, split pin
__ 1,3mmHexagonWrench
__ 1,LockingTool
__ 1,10mmSpannerWrench
__ Safety Glasses
1
23
4
5
6
7
89
10
11
12
13 14
15
16
17
18
19
20
21 22
IMPORTANT
ThissparkignitionsystemcomplieswithCanadianICES-002

POWER EDGER
OPERATOR'SMANUAL 11
1. DEBRIS SHIELD/FLAP - Mounted over the cutting attachment. Helps protect operator by deflecting debris produced
during the edging operation.
2. BLADE - Rotates to provide cutting action.
3. WHEEL - Adjustable up/down, sets depth of blade.
4. GUARDDECAL(Seepage4)
5. DRIVESHAFTASSEMBLY-Containsaspeciallydesignedlinerandtheflexibledriveshaft.
6. SHAFTDECAL(SPANISHDECAL)(Seepage4)
7. SHAFTDECAL(Seepage4)
8. FRONT HANDLE - The front handle can be repositioned for comfortable operation by loosening the screws and moving
the handle.
9. STOPSWITCH-
PE-2000 - "Toggle Switch" mounted on the engine. Move switch UP to RUN, DOWN to STOP.
PE-2400/3100- "SlideSwitch" mountedon topof thethrottle TriggerHousing. Move switchFORWARD toRUN, BACK
toSTOP.
10. THROTTLETRIGGER-Springloadedtoreturntoidlewhenreleased. Whenaccelerating,presstriggergraduallyfor
best operating technique.
11. GRIP-Rear(righthand)handle.
12. ARM REST - Provides arm rest during operation and protects arm from the hot engine.
13. CHOKE-Thechokecontrol islocated onthe topof theairfiltercase(PE-2400,3100);sideof theair filtercase (PE-2000).
PE-2000 - Move lever to "COLD START" to close choke for cold starting. Move lever to "RUN" position to open choke.
PE-2400/3100 - Pull choke knob up to close choke for cold starting. Push knob down to "RUN" position to open choke.
14. SPARK PLUG-Providessparktoignitefuelmixture.
15. MUFFLER/SPARKARRESTOR-Thesparkarrestormufflercontrolstheexhaustnoiseandpreventshot,glowing
particlesof carbonfromleaving themuffler.
16. FUELTANK-Containsfuelandfuelfilter.
17. RECOILSTARTERHANDLE-Pullrecoilhandleslowlyuntilstarterengages,thenquicklyandfirmly.DONOTlet
handle snap back or damage to unit will occur.
18. FUELTANKCAP-Coverandsealsfueltank.
19. PRIMERBULB-Beforestartingand afterfillingthe fueltank,pump primerbulb10times oruntila steadystreamof fuel
without air is visible through the "clear" fuel return line.
20. AIRCLEANER-Containsreplaceablefeltelement.
21. OPERATORSMANUAL - Readand understandthis manualbefore operation. Keepmanual ina safelocation for future
reference, i.e., operation, maintenance, storage and specifications.
22. SAFETYMANUAL -Included inplasticbag (co-pack).Read beforeoperation andkeepinasafe placefor futurereference
to learn proper, safe operating techniques.

12
SPECFICATIONS
* Certain internal combustion engines operated in forest, brush and/or grass-covered areas in Washington, Oregon,
Idaho, California, Minnesota, New Jersey and Maine must be equipped with a spark arrestor. This requirement also
applies to all U.S. Forest Service lands. In some of these areas, the spark arrestor system must be certified per USDA
Forest Service regulations SAEJ335. Check with your local or state authorities for specific regulations in your area.
Failure to follow these requirements is a violation of the law.
LEDOME2/E10002-EPE1/10042-EPE1/10013-EP
htgneL).ni0.96(mm3571).ni7.96(mm0771).ni7.07(mm5971
htdiW).ni0.31(mm03
3).ni0.31(mm033).ni0.31(mm033
thgieH).ni8.11(mm003).ni8.11(mm003).ni8.11(mm003
)daehrettuc/wyrd(thgieW).bl2.2
1(gk5.5).bl0.31(gk9.5).bl6.51(gk1.7
epyTenignE enigneenilosagrednilycelgnis,ekorts-owt,deloocriA
eroB).ni86
2.1(mm2.23).ni43.1(mm0.43).ni24.1(mm0.63
ekortS).ni420.1(mm0.62).ni420.1(mm0.62).ni81.1(mm0.03
tnemecalpsiD).
ni.uc92.1(cc2.12).ni.uc44.1(cc6.32).ni.uc98.1(cc5.03
tsuahxErelffuMrotserrAkrapS*
egrup/wmgarhpaidroterubr
aCU1CledomamaZTWledomorblaWTWledomorblaW
metsySnoitingI )noitingiegrahcsidroticapac(IDC
gulPkrapS ).ni620.0(
mm56.0,A7-RMPBKGN
leuF )liOekorts-owTdnaenilosaG(dexiM
oitaRliO/leuF lioenignedeloocriaekorts-owt,ecnamro
frePhgiHOHCE1:05
enilosaG %01nahterom,lohoclalyhtemgniniatnocleufesuTONOD.dedaelnuenatcO98 .EBTM%51roloh
oclalyhte
liO lioenignedeloocriaekorts-owt,ecnamrofrePhgiHOHCE1:05
yticapaCknaTleuF).zo.lfSU0.41(.til4.0).
zo.lfSU0.41(.til4.0).zo.lfSU1.72(.til8.0
metsySretratS retratSdniweRcitamotuA
hctulC epyTlagufirtneC
tfahSe
virD tfahselbixelf.ni4/1
noitceriDnoitatoR edismorfdeweivesiwkcolC
daeHregdE edalblateM
htgneLedalB ).ni0.8(
mm2.302
htdiWedalB ).ni2(mm8.05
ssenkcihTedalB).ni9.0(mm5.2 ).ni081.0(mm5.4
eldnaH pirG-thgiR,pool-D-tfeL
noi
tcudeRnoitarbiV noihsuCrebbuR
deepSeldIMPR0013-0052MPR0013-0052MPR0003-0042
deepSelttorhTnepOediWMPR00001-00
09MPR00011-00001MPR00011-0059

POWER EDGER
OPERATOR'SMANUAL 13
ASSEMBLY
DRIVE SHAFT/POWER HEAD
ToolsRequired:8mmx10mmOpenEndWrench(PE-2000,PE-2400),
4mmHexWrench(PE-3100)
1. Stand engine on a level surface.
2a. (PE-2000/2400) Loosen the two bolts (A) at drive shaft end of
engine.
2b. (PE-3100) Loosen two bolts (A) at drive shaft end of engine and
remove center drive shaft location bolt (B).
3. Carefully fit drive shaft assembly to engine, making sure that inner
drive shaft engages into clutch mount.
NOTE
The line on the drive shaft housing must be in contact with the
engine (arrow on drive shaft indicates line).
4a. (PE-2000/2400) Rotate the drive shaft housing until edger housing is
in line with the engine.
4b. (PE-3100) Rotate drive shaft housing until locating hole lines up with
center location hole in clamp and install center bolt (B).
5. Tighten bolts (A).
THROTTLE LINKAGE
ToolsRequired:8mmx10mmOpenEndWrench(AllModels),3mm
Wrench(PE-2400)
1. Close choke andremove airfilter cover.
2. Loosen nut (A) and place threaded end of throttle linkage in
bracket slot. Finger tighten nut (A). Place inner cable in slot of
carburetor(B).
3. Check throttle action, for freedom of movement and that the inner
throttle linkage allows the carburetor throttle plate (E) to return to
idle stop. Adjust cable nut counter clockwise to increase inner
throttle lnkage length and allow throttle plate to rest against stop.
4. Tighten nut (A).
A
A
AB
PE-2400
PE-3100
PE-2000
PE-2000
A

14
FRONT HANDLE
Tools Required:Cross-Head Screwdriver
1. Assemble front handle and bracket loosely to drive shaft.
2. Position front handle in comfortable operating position and tighten
screws.
PE-2400
PE-3100 FRONT
HANDLE
NOTE
Steps5,6&7requiredforPE-2400andPE-3100only.
5. Connect ignition leads (C).
6. (PE-2400) Secure ground lead under screw (D) on housing.
7. Install airfilter andcover.
PE-2400
E
PE-3100
C
PE-2000
FRONT
HANDLE

POWER EDGER
OPERATOR'SMANUAL 15
PRE-OPERATION
FUEL
Fuel Requirements --
Gasoline - Use 89 Octane [ ] gasoline known to be good quality.
Gasolinemay containupto10%Ethanol (grainalcohol) or15%MTBE
(methyltertiary-butyl ether).Gasoline containingmethanol(wood
alcohol) is NOT approved.
Two-StrokeOil- Atwo-strokeengineoilmeetingISO-L-EGDStandard
(ISO/CD13738),mustbeused.EchobrandPremium50:1oilmeetsthis
standard. Engine problems due to inadequate lubrication caused by
failuretouseanISO-L-EGDapprovedoil,suchasEchoPremium50:1
Two-strokeOil,willvoidthetwo-strokeenginewarranty.(Emission
related parts only are covered for two years, regardless of two-stroke
oil used, per the statement listed in the EPA Phase I/California Emission
DefectWarrantyExplanation.)
Mixing-Follow directions on the oil container.
Handling Fuel --
WARNING DANGER
FuelisVERYflammable.Useextremecarewhenmixing,storingor
handling or serious personal injury may result.
• Use an approved fuel container.
• DONOTsmokenearfuel.
• DONOT allowflamesor sparksnearfuel.
• Fuel tanks/cans may be under pressure. Always loosen fuel
caps slowly allowing pressure to equalize.
• NEVERrefuelaunitwhenthe engineisHOT!
• NEVERrefuel aunitwith theenginerunning.
• DO NOT fuel tanks indoors. ALWAYS fill fuel tanks outdoors
over bare ground.
• Securely tighten fuel cap after refueling.
• Inspect for fuel leakage. If fuel leakage is found, do not start or
operate unit until leakage is repaired.
After Refueling —
•Wipe any spilled fuel from the unit.
•Move at least 3M. (10 ft.) from refueling location before starting.
Afteruse—
•DO NOT store a unit with fuel in its tank. Leaks can occur. Return
unused fuel to an approved fuel storage container.
Storage —
Fuel storage laws vary by locality. Contact your local government for
the laws affecting your area. As a precaution, store fuel in an approved,
air tight container. Store in a well ventilated, unoccupied building, away
from sparks and flames. Do not store fuel longer than 30 days.
SM TWTF S
1234567
8 9 10 11 12 13 14
15 16 17 18 19 20 21
22 23 24 25 26 27 28
29 30 31
R+M
2
MOVE 10' MINIMUM

16
OPERATION
• Before starting the unit, equip yourself and any other person working
within the 50 ft. (15M) Safety Zone with the required Protective
Equipment and clothing.
• Provide all operators of this equipment with the Operator's Manual
and instruction for safe operation.
• During operation, the complete unit, especially the drive shaft
housing and the bearing housing may become very hot, too hot to
touch. Avoid contact during and immediately after operation.
WARNING DANGER
When engine starts, the blade may rotate, even with throttle trigger in
idle(Release) position.
1. Stop Switch - Start/Run.
Move stop switch button (A) away from the STOP position.
2. Close Choke-ColdStart.
Move choke (B) to "Cold Start" position.
3. Primer-PumpBulb.
Pumpprimerbulb(C)10times.Fuelwillbevisibleandflowfreelyin
the "Clear" fuel return line.
PE-2000
PE-2400
PE-3100
STARTING COLD ENGINE
NOTE
•Check unit for loose nuts, bolts and screws before starting.
•Always clear work area of debris before starting operation.
•Always hold the unit firmly on the ground.
•When pulling recoil starter rope, use short pulls, 1/2 to 2/3 of
rope length.
•Do not allow the recoil starter handle to snap back against the
housing.
•Always hold the unit firmly.
PE-2000
A
A
C
B
WARNING DANGER
Inspect starting area for hazards such as rocks, glass, debris etc. which
could be contacted by the cutting attachment when starting. Keep
helpers and bystanders at least 15 M (50 ft.) from starting area,
otherwise serious personal injury may result. D

POWER EDGER
OPERATOR'SMANUAL 17
4. Starting -Laytrimmerona flat,cleararea.Firmlygrasp throttlegrip
with left hand and fully depress throttle trigger to wide open
position. Rapidly pull recoil starter handle/rope (D) until engine
fires(ormaximumfive[5]pulls).
5. After engine fires (or five [5] pulls), move choke lever back to
"RUN" position. Hold throttle trigger fully depressed and pull recoil
starter handle/rope until engine starts and runs. Release throttle
trigger and allow unit to warn up at idle for several minutes.
NOTE
If engine does not start with choke in "RUN" position after 4 pulls,
repeat instructions.
6. After engine warm up, gradually depress throttle trigger to increase
engine RPM to operating speed.
STARTING WARM ENGINE
WARNING DANGER
Blade should not move at idle. If blade moves, readjust carburetor
according to Carburetor Adjustment instructions in the manual or see
yourECHO dealer, otherwiseserious personalinjury may result.
1. Stop Switch - Start/Run.
Move stop switch button (A) away from the STOP position.
2. Primer-PumpBulb.
Pumpprimer bulbuntil fuelis visibleint he"Clear" fuelreturn line.
3. Starting -Lay trimmeron aflat, cleararea andpull recoilstarter
handle/rope (D) until engine fires.
NOTE
If the engine does not start after 4 pulls, use Cold Start Procedure.
PE-2400
PE-3100 B
PE-2000
PE-2400
PE-3100
PE-2000
A
A
C
B
D
C
D
D

18
If engine does not stop, close choke to stall engine. Have your
ECHO Dealer inspect and repair stop switch before using edger
again or serious personal injury may result.
STOPPING ENGINE
1. Release throttle trigger and allow engine to idle.
2. Place stop switch in STOP position.
WARNING DANGER
PE-2000
PE-2400
PE-3100
STOP
STOP
OPERATING TECHNIQUES
1. Before edging, water the area to soften the ground to make edging
easier.
2 Before edging, check the area and remove all obstacles and objects
that could be thrown.
3. Plan to edge regularly to make it easier to keep a neat edge and to
avoid having to make more than one pass.
NOTE
Blade depth may have to be adjusted due to differences in height
between the hard surface and the top of the grass.
WARNING DANGER
Never adjust blade height with engine running, otherwise serious
personal injury may result.
4. Adjust the blade's depth of cut to produce a fine cut between
sidewalk and grass using a minimum blade depth, usually with
about 1/2" of the blade into the ground. WHEEL WING
NUT
DECREASE
DEPTH
INCREASE
DEPTH
1/2"

POWER EDGER
OPERATOR'SMANUAL 19
5. Before edging, plan your direction of travel so that the unit will
always be positioned on your right side and so that you walk on a
hard surface whenever possible.
6. Hold edger as shown.
WARNING DANGER
Before edging, be sure to read and understand the entire Operator's
Manual to avoid the chance of serious injury.
7. When starting to edge, run the engine at full throttle, and lower the
blade gently into the ground, being careful not to hit the concrete
with the blade.
8. Don't force the blade. Move as quickly as the blade will allow.
WARNING DANGER
The complete unit, specifically the drive shaft assembly may become
very hot (to hot to touch) during use. Avoid contact during and
immediatelyafter operation,otherwiseserious personalinjurymay
result.
MAINTENANCE
Your ECHO edger is designed to provide many hours of trouble free service. Regular scheduled maintenance will help
your edger achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take your
unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOURSELF or have the
ECHO Dealer do it, each maintenance task has been graded. If the task is not listed, see your ECHO Dealer for repairs.
Toolsrequired: 1" or 2" medium bristle paint brush, 8"-10" (203-254 mm) length of wire with one end bent into a hook.
Clean rag, funnel, and an approved fuel container, Scrench screw driver and Feeler gauge (preferably a wire gauge),
Cross-HeadScrewdriver, 3mmHexWrench, 4mmHexWrench, PointedWoodStick,Soft MetalBrush,SlottedScrew-
driver,Tachometer(ECHOP/N99051130017), 8mmOpenEndWrench.
SKILL LEVEL
Level1= Easy to do. Most required tools come with unit.
Level2= Moderate difficulty.Some specializedtools may berequired.
Level3= Experiencerequired.Specializedtoolsarerequired.
ECHO offers REPOWER Maintenance Kits and Parts to make your maintenance job easier. Just below each task heading
are listed the various part numbers required for that task. See your ECHO dealer for these parts.

20
MAINTENACE INTERVALS
/TNENOPMOC METSYS ECNANETNIAM ERUDECORP
D'QER LLIKS LEVEL ROYLIAD EROFEB ESU
YREVE LEUFER
3SHTNOM 09RO SRUOH 6SHTNOM 072RO SRUOH
YLRAEY 006 SRUOH
serudecorPecnanetniaMrelaeDohcEdednemmoceR
troPtsuahxErednilyCnobraceD/naelC/tcepsnI 3C/I
serudecorPecnan
etniaMflesruoY-tI-oD
retliFriAecalpeR/naelC/tcepsnI 1C/I*R
ekohCnaelC/tcepsnI 2C/I
retliFleuFecalpeR/tcepsnI 1I*
R
skael,metsySleuFecalpeR/tcepsnI 1I*R/I
metsySgnilooCnaelC/tcepsnI 2C/I
rotserrAkrapSrelffuMecalpeR/tcepsnI 2C
/I*R/I
tfahSevirDesaerG 2)1(I
gnisuoHraeGesaerG 2)2(I
epoRretratSlioceRnaelC/tcepsnI 1*C/I*R/I
gulPkrapSnaelC/tcep
snI 2C/I*R
tnemecalpeRedalBecalpeR/tcepsnI 1II *R/I
stloB/stuN/swercSecalpeR/nethgiT/tcepsnI 1*R/I
SEDOCRETTELERUDECORPECNANETNIAM NAELC=C,ECALPER=R,TCEPSNI=I:
-ETONTNATROPMI deriuqerfoycneuqerfehtenimretedlliwecneirepxeruoydnaesulaut
cA.mumixameranwohsslavretniemiT
.ecnanetniam :SETONERUDECORPECNANETNIAM)1( OHCEylppA
®
EBUL
MT
.esufosruoh05yreve
)2( OHCEylppA
®
EBUL
MT
.esufosruoh52-51yreve
*..noitcepsnignirudraewroegamadfognidnifehtnodesaberaecalperotsnoitadnemmocerllA