Echo PE-2000 Type 1/1E User manual

POWER EDGER
OPERATOR'SMANUAL 1
PowerEdger
Operator'sManual
MODELS PE-2000 Type 1/1E
Serial Number 001001 & Up
PE-2000 Type 2E
Serial Number 508036 & Up
89861058832
08/01
X7502124502
PE-2400 Type 1/1E
Serial Number 001001 & Up
PE-3100 Type 1/1E
Serial Number 001001 & Up
WARNING DANGER
Readrulesforsafeoperationandinstructionscarefully. ECHOprovidesan
Operator'sManualandaSafetyManual. Bothmustbereadandunderstoodfor
properandsafeoperation.

2
INTRODUCTION
Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-job-
dependability. Read and understand this manual and the SAFETY MANUAL you found in the same package. You will
find both easy to use and full of helpful operations tips and SAFETY messages.
THE OPERATOR'SMANUAL
Contains specifications and information for operation, starting,
stopping, maintenance, storage and assembly specific to this product.
THE SAFETY MANUAL
Explains possible hazards involved with the use of Edgers and the
measures you should take to make their use safer.
TABLE OF CONTENTS
Introduction ...............................................................2
-The Operator's Manual .............................................. 2
- The Safety Manual ..................................................... 2
Manual Safety Symbols and Important Information ..3
Safety .........................................................................3
- Decals..................................................................4
- InternationalSymbols .........................................4
Safety Instructions ....................................................4
- Personal Condition and Safety Equipment..........4
- ExtendedOperation/ExtremeConditions.............5
- Equipment ...........................................................5
- SafeOperation.....................................................6
EmissionControl........................................................6
Description ................................................................7
- Contents..............................................................7
Assembly ................................................................. 10
- Specifications .................................................... 10
- DriveShaft/PowerHead .................................... 11
- ThrottleCable.................................................... 11
- LoopHandle...................................................... 12
Pre-Operation ........................................................... 13
- Fuel ................................................................... 13
Operation ................................................................. 14
- StartingColdEngine ......................................... 14
- StartingWarmEngine ....................................... 15
- Stopping Engine................................................ 15
- Operating Techniques....................................... 16
Maintenance ............................................................ 17
- SkillLevels ........................................................ 17
- Maintenance Intervals ...................................... 17
- Airfilter ............................................................. 18
- FuelFilter .......................................................... 18
- SparkPlug ......................................................... 19
- CoolingSystem ................................................. 19
- ExhaustSystem ................................................. 20
- CarburetorAdjustment Emission ...................... 21
- Carburetor Adjustment Non Emission .............. 22
- Lubrication ........................................................ 23
Troubleshooting ...................................................... 25
Storage..................................................................... 26
ServicingInformation............................................... 28
- Parts .................................................................. 28
- Service............................................................... 28
- Echo Consumer Product Support...................... 28
- Warranty Card................................................... 28
- Additional or Replacement Manuals................. 28
Specifications, descriptions, and illustrative material in this
literature are as accurate as known at the time of publication,
but are subject to change without notice. Illustrations may
include optional equipment and accessories, and may not
include all standard equipment.
Copyright© 2001 By Echo, Incorporated
All Rights Reserved.

POWER EDGER
OPERATOR'SMANUAL 3
The circle with the slash symbol means whatever
is shown within the circle is prohibited.
This symbol accompanied by the words WARNINGand
DANGER calls attention to an act or condition that can
lead to serious personal injury to operator and bystanders.
MANUAL SAFETY SYMBOLS AND IMPORTANT INFORMATION
Throughout this manual and on the product itself, you will find safety
alerts and helpful information messages preceded by symbols or key
words. The following is an explanation of those symbols and key
words.
IMPORTANT
The enclosed message provides information
necessary for the protection of the unit.
NOTE
This enclosed message provides tips for use,
care and maintenance of the unit.
SAFETY
DECALS
Locate these safety decals on your unit. The complete unit illustration
foundin the "DESCRIPTION" section will helpyou locatethem. Make
sure the decals are legible and that you understand and follow the
instructions on them. If a decal cannot be read, a new one can be
orderedfromyourECHODealer.SeePARTSORDERINGinstructions
forspecificinformation.
These decals are in English only:
Shaft Decal
P/N 89016025560
P/N 89016052631
P/N89016006361
IMPORTANT
NOTE
Guard Decal

4
INTERNATIONAL SYMBOLS
SAFETYINSTRUCTIONS
PERSONAL CONDITION AND SAFETY EQUIPMENT
WARNING DANGER
Edger users risk injury to themselves and others if the edger is used improperly or safety precautions are not
followed. Proper clothing and safety gear must be worn when operating an edger.
Eye Protection
Wear eye protection that meets ANSI Z87.1 or CE require-
ments whenever you operate the edger.
Hand Protection
Wear no-slip, heavy-duty work gloves to improve your
grip on the edger handles. Gloves also reduce the
transmission of machine vibration to your hands.
Hearing Protection
ECHOrecommendswearinghearing protectionwhenever
unit is used.
Proper Clothing
Wear snug fitting, durable clothing:
• Pants should have long legs, shirts with long sleeves.
• DONOTWEARSHORTS,
• DONOTWEARTIES,SCARVES,JEWELRY.
Wear sturdy work shoes with non-skid soles:
• DONOTWEAROPENTOEDSHOES,
• DONOTOPERATEUNITBAREFOOTED.
Hot Humid Weather
Heavy protective clothing can increase operator fatigue
which may lead to heat stroke. Schedule heavy work for
early morning or late afternoon hours when temperatures
arecooler.
Symbol
description/
application
Symbolform/
shape
Symbol
description/
application
Symbolform/
shape
Hot
Surface
Carburetor
adjustment
-Idlespeed
Carburetor
adjustment
- High speed
mixture
Symbol
description/
application
Symbolform/
shape
Symbol
description/
application
Symbolform/
shape
Read and understand
Operator's Manual.
Wear eyes, ears and
head protection
Emergencystop
Fuel and oil mixture
FingerSevering
Carburetor
adjustment
-Low speed
mixture
Safety/Alert
Avoidallpower
lines.This unitis
notinsulated
againstelectrical
current.
Wearhand
protection.Use
twohanded.
DONOTsmoke
nearfuel.
DONOT allow
flamesorsparks
nearfuel.
Wearslip
resistantfoot
wear.
Enginechoke
control.
Ignition
ON/OFF
Primerbulb
Keepbystandersaway
15 m (50 ft.)
Keepfeetaway
fromblade
Thrown
objects
Direction of
blade

POWER EDGER
OPERATOR'SMANUAL 5
EXTENDED OPERATION/EXTREME CONDITIONS
Vibration and Cold
It is believed that a condition called Raynaud’s Phenomenon, which
affects the fingers of certain individuals, may be brought about by
exposure to vibration and cold. Exposure to vibration and cold may
cause tingling and burning sensations, followed by loss of color and
numbness in the fingers. The following precautions are strongly
recommendedbecausetheminimumexposurewhichmighttriggerthe
ailmentisunknown.
• Keep your body warm, especially the head, neck, feet, ankles, hands,
and wrists.
• Maintain good blood circulation by performing vigorous armexercises
during frequent work breaks, and also by not smoking.
• Limit the hours of operation. Try to fill each day with jobs where
operating the edger or other hand-held power equipment is not
required.
• If you experience discomfort, redness, and swelling of the fingers,
followed by whitening and loss of feeling, consult your physician
before further exposing yourself to cold and vibration.
Repetitive Stress Injuries
It is believed that overusing the muscles and tendons of the fingers,
hands, arms, and shoulders may cause soreness, swelling, numbness,
weakness, and extreme pain in those areas. Certain repetitive hand
activities may put you at a high risk for developing a Repetitive Stress
Injury(RSI).AnextremeRSIconditionisCarpalTunnelSyndrome
(CTS), which could occur when your wrist swells and squeezes a vital
nerve that runs through the area. Some believe that prolonged exposure
to vibration may contribute to CTS. CTS can cause severe pain for
months or even years.
To reduce the risk of RSI/CTS, do the
following:
• Avoid using your wrist in a bent, extended
or twisted position. Instead try to maintain
a straight wrist position. Also, when
grasping, use your whole hand, not just
the thumb and index finger.
• Takeperiodicbreakstominimizerepetition
and rest your hands.
• Reduce the speed and force with which
you do the repetitive movement.
• Do exercises to strengthen the hand and
armmuscles.
• Immediately stop using all power equip-
ment and consult a doctor if you feel
tingling, numbness or pain in the fingers,
hands, wrists, or arms. The sooner RSI/
CTSisdiagnosed, themorelikelyperma-
nent nerve and muscle damage can be
prevented.
EQUIPMENT
• Check unit for loose/missing nuts, bolts and screws. Tighten and/or
replace as needed.
• Inspect fuel lines, tank and area around carburetor for fuel leaks. DO
NOT operate unit if leaks are found.
• Inspect shield for damage and is securely in place. Replace if shield is
damaged or missing.
• Check that the cutting attachment is firmly attached and in safe
operating condition.
• Check that front handle is adjusted for safe, comfortable operation.
See Assembly for proper adjustment.
• Keep exhaust area clear of flammable debris. Avoid contact during
andimmediatelyafteroperation.

6
SAFE OPERATION
WARNING DANGER
Do not operate this product indoors or in inadequately ventilated
areas. Engine exhaust contains poisonous emissions and can cause
serious injury or death.
• Provide all operators of this equipment with the Operator's Manual
and Safety Manual for instructions on safe operation.
KeepAFirmGrip
• Hold the left and right handles with both hands, with thumbs and
fingers tightly encircling the handles
KeepASolidStance
• Maintain footing and balance at all times. Do not stand on slippery,
uneven or unstable surfaces. Do not work in odd positions or on
ladders. Do not over-reach.
AnEmissionControlLabelislocatedontheengine. (This is anEXAMPLEONLY,information on labelvariesbyengine
family).
EMISSION CONTROL
The emission control system for this engine is EM (Engine Modification).
IMPORTANT ENGINE INFORMATION
ENGINE FAMILY: TEH024UB24RC
DISPLACEMENT: 23.6 CC
THIS ENGINE MEETS U.S. EPA PH1 AND 1996 -
1998 CALIFORNIA EMISSION REGULATIONS
FOR ULGE ENGINES. REFER TO OWNER'S
MANUAL FOR MAINTENANCE SPECIFICATIONS
AND ADJUSTMENTS.

POWER EDGER
OPERATOR'SMANUAL 7
20 21
DESCRIPTION
The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions,
shield installation and positioning of the front handle are necessary.
After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing
parts. Use the contents list to check for missing parts.
CONTENTS
__1, Edger Assembly
__1,PowerHead
__1, Drive Shaft Assembly
__1,PlasticBag(Co-Pack)
__1, Operators Manual
__1, Safety Manual
__1, Warranty Registration Card
__1,ECHOEmissionsandWarrantyStatement
__1,50:11Gal.ECHOOilMix
__1, Front Handle
__2,bolt5x40mm
__2, nut 5
__1, split pin
__1,Scrench(CombinationSparkPlugSocket/Screwdriver
__1,LockingTool
__1,10mm SpannerWrench
__Safety Glasses
PE-2000
1
2
3
4
5
67
8
9
10
11
12
13
14
15
1617
18
19

8
20 21
CONTENTS
__ 1, Edger Assembly
__ 1,PowerHead
__ 1,Drive Shaft Assembly
__ 1,PlasticBag(Co-Pack)
__ 1, Operators Manual
__ 1, Safety Manual
__ 1, Warranty Registration Card
__ 1,ECHOEmissions andWarrantyStatement
__ 1,50:11Gal.ECHOOilMix
__ 1,FrontHandle
__ 4,5X35mmscrews
__ 4,5 mmnuts
__ 1,Scrench(CombinationSparkPlugSocket/Screwdriver
__ 1, split pin
__ 1,3mmHexagonWrench
__ 1,LockingTool
__ 1,10mmSpannerWrench
__ Safety Glasses
PE-2400
PE-3100
1
2
3
4
5
67
8
9
10
12 13
14
15
16
17
18
19 11

POWER EDGER
OPERATOR'SMANUAL 9
1. TOPGUARD-Protectsarmfromthehotengine.
2. FRONT HANDLE - The front handle can be repositioned for comfortable operation by loosening the screws and
moving the handle.
3. SHAFTDECAL(Seepage3)
4. GUARDDECAL(Seepage3)
5. DEBRIS SHIELD/FLAP - Mounted over the cutting attachment. Helps protect operator by deflecting debris
produced during the edging operation.
6. BLADE - Rotates to provide cutting action.
7. WHEEL - Adjustable up/down, sets depth of blade.
8. DRIVESHAFTASSEMBLY-Containsaspeciallydesignedlinerandtheflexibledriveshaft.
9. THROTTLETRIGGER-Springloadedtoreturntoidlewhenreleased. Whenaccelerating,presstriggergradually
for best operating technique.
10. GRIP-Rear(righthand)handle.
11. STOPSWITCH-
PE-2000 - "Toggle Switch" mounted on the engine. Move switch UP to RUN, DOWN to STOP.
PE-2400/3100- "Slide Switch" mountedontop of the throttle TriggerHousing. Moveswitch FORWARD to RUN,
BACKtoSTOP.
12. CHOKE-The choke controlislocated on the top oftheairfilter case (PE-2400, 3100),or ontheside of the air filter
case(PE-2000).
PE-2000 - Move lever to "COLD START" to close choke for cold starting. Move lever to "RUN" position to open
choke.
PE-2400/3100 - Pull choke knob up to close choke for cold starting. Push knob down to "RUN" position to open
choke.
13. SPARK PLUG-Providessparktoignitefuelmixture.
14. MUFFLER/SPARKARRESTOR-Thesparkarrestormufflercontrolstheexhaustnoiseandpreventshot,glowing
particlesofcarbonfrom leaving the muffler.
15. FUELTANK-Containsfuelandfuelfilter.
16. RECOILSTARTERHANDLE-Pullrecoilhandleslowlyuntilstarterengages,thenquicklyandfirmly.DONOTlet
handle snap back or damage to unit will occur.
17. FUELTANKCAP-Coverandsealsfueltank.
18. PRIMERBULB- Pumping primerbulbbeforestarting enginedrawsfresh fuelfromthefuel tankprimingthecarbure-
tor for starting. Pump primer bulb until fuel is visible and flows freely in the clear fuel tank return line. Pump bulb an
additional4or 5times.
19. AIRCLEANER-Containsreplaceablefeltelement.
20. OPERATORSMANUAL- Read and understandthis manualbefore assemblyoroperation.Keep manual in a safe
location for future reference, i.e., operation, maintenance, storage and specifications.
21. SAFETYMANUAL - Read and understand this manual before assembly or operation, and keep in a safe place for
future reference to learn proper, safe operating techniques.

10
ASSEMBLY
SPECFICATIONS
LEDOME2/E10002-EPE1/10042-EPE1/10013-EP
htgneL).ni0.96(mm3571).ni7.96(mm0771).ni7.07(mm5971
htdiW).ni0.31(mm03
3).ni0.31(mm033).ni0.31(mm033
thgieH).ni8.11(mm003).ni8.11(mm003).ni8.11(mm003
)daehrettuc/wyrd(thgieW).bl2.2
1(gk5.5).bl0.31(gk9.5).bl6.51(gk1.7
epyTenignE enigneenilosagrednilycelgnis,ekorts-owt,deloocriA
eroB).ni86
2.1(mm2.23).ni43.1(mm0.43).ni24.1(mm0.63
ekortS).ni420.1(mm0.62).ni420.1(mm0.62).ni81.1(mm0.03
tnemecalpsiD).
ni.uc92.1(cc2.12).ni.uc44.1(cc6.32).ni.uc98.1(cc5.03
tsuahxErelffuMrotserrAkrapS*
egrup/wmgarhpaidroterubr
aCU1CledomamaZTWledomorblaWTWledomorblaW
metsySnoitingI )noitingiegrahcsidroticapac(IDC
gulPkrapS ,A7-MPBKGN ).ni620.0(mm56.0 Y7-JCnoipmahCroY7-MPBKGN ).ni620.0(mm56.0
leuF )liOekorts-owTdnaenilosaG(dexiM
oitaRliO/l
euF lioenignedeloocriaekorts-owt,ecnamrofrePhgiHOHCE1:05
enilosaG %01nahterom,lohoclalyhtemgniniatnocleu
fesuTONOD.dedaelnuenatcO98 .EBTM%51rolohoclalyhte
liO lioenignedeloocriaekorts-owt,ecnamrofrePhgiHOHCE1:
05
yticapaCknaTleuF).zo.lfSU0.41(.til4.0).zo.lfSU0.41(.til4.0).zo.lfSU1.72(.til8.0
metsySretratS retratSdni
weRcitamotuA
hctulC epyTlagufirtneC
tfahSevirD tfahselbixelf.ni4/1
noitceriDnoitatoR edismorfdeweivesiwkcol
C
daeHregdE edalblateM
htgneLedalB ).ni0.8(mm2.302
htdiWedalB ).ni2(mm8.05
ssenkcihTedalB).ni9.0(mm5.2 ).ni081
.0(mm5.4
eldnaH pirG-thgiR,pool-D-tfeL
noitcudeRnoitarbiV noihsuCrebbuR
deepSeldIMPR0013-0052MPR0013-0052MPR0
003-0042
deepSelttorhTnepOediWMPR00001-0009MPR00011-00001MPR00011-0059

POWER EDGER
OPERATOR'SMANUAL 11
DRIVE SHAFT/POWER HEAD
Tools Required: 8mmx10mmOpenEndWrench(PE-2000,PE-2400),
4mmHexWrench(PE-3100)
1. Stand engine on a level surface.
2a. (PE-2000/2400) Loosen the two bolts (A) at drive shaft end of
engine.
2b. (PE-3100) Loosen two bolts (A) at drive shaft end of engine and
remove center drive shaft location bolt (B).
3. Carefully fit drive shaft assembly to engine, making sure that inner
drive shaft engages into clutch mount.
NOTE
The line on the drive shaft housing must be in contact with the
engine (arrow on drive shaft indicates line).
4a. (PE-2000/2400) Rotate the drive shaft housing until edger housing is
in line with the engine.
4b. (PE-3100) Rotate drive shaft housing until locating hole lines up with
center location hole in clamp and install center bolt (B).
5. Tighten bolts (A).
THROTTLE LINKAGE
ToolsRequired:8mmx10mmOpenEndWrench(AllModels),3mm
Wrench(PE-2400)
1. Close chokeand removeairfiltercover.
2. Loosen nut (A) and place threaded end of throttle linkage in
bracket slot. Finger tighten nut (A). Place inner cable in slot of
carburetor(B).
3. Check throttle action, for freedom of movement and that the inner
throttle linkage allows the carburetor throttle plate (E) to return to
idle stop. Adjust cable nut counter clockwise to increase inner
throttle lnkage length and allow throttle plate to rest against stop.
4. Tighten nut (A).
A
A
AB
PE-2400
PE-3100
PE-2000
PE-2000
A

12
PE-2400
PE-3100 FRONT
HANDLE
PE-2400
PE-3100
NOTE
Steps5,6&7requiredforPE-2400andPE-3100only.
5. Connect ignition leads (C).
6. (PE-2400) Secure ground lead under screw (D) on housing.
7. Install air filter and cover.
FRONT HANDLE
Tools Required:Cross-Head Screwdriver
(PE-2000)
1. Assemble loop handle (A) and bottom bracket (B) loosely using
screws (C) and nuts (D) to loop handle collar (E), located on drive
shaft(F).
2. Position handle in comfortable operating position and tighten
screws(C).
(PE-2400, 3100)
1. Assemble front handle and bracket loosely to drive shaft.
2. Position front handle in comfortable operating position and tighten
screws.
PE-2000
LOOP
HANDLE
A
B
C
D
E
F

POWER EDGER
OPERATOR'SMANUAL 13
PRE-OPERATION
FUEL
Fuel Requirements
Gasoline - Use 89 Octane [ (R+M) ÷ 2 ] gasoline known to be good
quality. Gasoline may contain up to 10% Ethanol (grain alcohol) or 15%
MTBE(methyltertiary-butylether).Gasolinecontainingmethanol
(wood alcohol) is NOT approved.
Two-StrokeOil-TwoStrokeOil-Atwo-stroke engine oilmeeting
ISO-L-EGD(ISO/CD13738)andJ.A.S.O.FCStandards,mustbeused.
Echo brand Premium 50:1 oil meets these standards. Engine problems
due to inadequate lubrication caused by failure to use an ISO-L-EGD
andJ.A.S.O.FCcertifiedoil,suchasEchoPremium50:1Two-strokeOil,
will void the two-stroke engine warranty. (Emission related parts only
are covered for two years, regardless of two-stroke oil used, per the
statement listed in the EPA Phase I/California Emission Defect War-
rantyExplanation.)
IMPORTANT
EchoPremium2-StrokeOilmaybemixedat50:1ratioforapplication
in all Echo engines sold in the past regardless of ratio specified in
those manuals.
Mixing Instructions
1. Fill an approved fuel container with half of the required amount of
gasoline.
2. Add 2-stroke oil to gasoline.
3. Close container and shake to mix oil with gasoline.
4. Addremaininggasolineandremix.
5. Install fuel container cap and wipe any spilled fuel from container
and surrounding area.
Handling Fuel
WARNING DANGER
FuelisVERYflammable.Useextremecarewhenmixing,storingor
handling, or serious personal injury may result.
• Use an approved fuel container.
• DONOTsmokenearfuel.
• DONOTallow flames or sparksnearfuel.
• Fuel tanks/cans may be under pressure. Always loosen fuel
caps slowly allowing pressure to equalize.
• NEVERrefuela unit whentheengineisHOT!
• NEVERrefuelaunit with the enginerunning.
• DONOT fill fuel tanks indoors.ALWAYS fillfueltanksoutdoors
over bare ground.
• Securely tighten fuel cap after refueling.
• Inspect for fuel leakage. If fuel leakage is found, do not start or
operate unit until leakage is repaired.
IMPORTANT
Spilled fuel is a leading cause of
hydrocarbon emissions. Some states
may require the use of automatic fuel
shut-off containers to reduce fuel
spillage.ContactyourECHOdealerfor
orderinginformation.
After refueling
• Wipe any spilled fuel from the unit.
• Moveatleast 3 m(10ft.)fromrefueling
location before starting the engine.
After use
• DO NOT store a unit with fuel in its tank.
Leaks can occur. Return unused fuel to an
approved fuel storage container.
Storage
Fuel storage laws vary by locality. Contact
your local government for the laws affecting
your area. As a precaution, store fuel in an
approved, air tight container. Store in a well
ventilated, unoccupied building, away from
sparks and flames. Do not store fuel longer
than 30 days.
IMPORTANT
Storedfuelages.Donotmixmorefuel
than you expect to use in thirty (30)
days, ninety (90) days when a fuel
stabilizeris added.
IMPORTANT
Stored two-stroke fuel may separate.
ALWAYS shake fuel container thor-
oughly before each use.

14
OPERATION
STARTING COLD ENGINE
NOTE
•Check unit for loose nuts, bolts and screws before starting.
•Always clear work area of debris before starting operation.
•Always position the unit firmly on the ground before starting.
•When pulling recoil starter rope, use short pulls, 1/2 to 2/3 of
rope length.
•Do not allow the recoil starter handle to snap back against the
housing.
•Always hold the unit firmly.
WARNING DANGER
When engine starts, the blade may rotate, even with throttle trigger in
idle(Release)position.
1. Stop Switch
Move stop switch button (A) away from the STOP position.
2. Choke
Move choke (B) to "Cold Start" position.
3. Primer Bulb
Pumpprimerbulb(C)untilfuelisvisibleinthe"Clear"fuelreturn
line.Pump bulb an additional 4or 5times.
WARNING DANGER
Inspect starting area for hazards such as rocks, glass, debris etc.
which could be contacted by the cutting attachment when starting.
Keep helpers and bystanders at least 15 m (50 ft.) from starting
area, otherwise serious personal injury may result.
4. Recoil Starter
Laytrimmerona flat,cleararea.Firmlygraspthrottlegripwithleft
hand and fully depress throttle trigger to wide open position.
Rapidly pull recoil starter handle/rope (D) until engine fires (or
maximumfive[5]pulls).
5. Choke
After engine fires (or five [5] pulls), move choke lever back to
"RUN" position. Hold throttle trigger fully depressed and pull
recoil starter handle/rope until engine starts and runs. Release
throttle trigger and allow unit to warn up at idle for several minutes.
NOTE
If engine does not start with choke in "RUN" position after 4 pulls,
repeat instructions.
6. Throttle Trigger
After engine warm up, gradually depress throttle trigger to increase
engine RPM to operating speed.
PE-2000
PE-2400
PE-3100
A
A
PE-2000
C
B
D
PE-2400
PE-3100 B
C
D

POWER EDGER
OPERATOR'SMANUAL 15
STARTING WARM ENGINE
WARNING DANGER
Blade should not move at idle. If blade moves, readjust carburetor
according to Carburetor Adjustment instructions in the manual or
see your ECHO dealer, otherwise serious personal injury may
result.
1. Stop Switch
Move stop switch button (A) away from the STOP position.
2. Primer Bulb
Pumpprimerbulb(C)untilfuelisvisibleinthe"Clear"fuelreturn
line.Pump bulb an additional 4or 5times.
3. Recoil Starter
Starting-Laytrimmeronaflat,cleararea and pull recoil starter
handle/rope (D) until engine fires.
NOTE
If the engine does not start after 4 pulls, use Cold Start Procedure.
STOPPING ENGINE
1. Throttle Trigger
Release throttle trigger and allow engine to idle.
2. Stop Switch
Place stop switch in STOP position.
WARNING DANGER
If engine does not stop, close choke to stall engine. Have your
ECHO Dealer inspect and repair stop switch before using edger
again or serious personal injury may result.
PE-2000
PE-2400
PE-3100
A
A
PE-2000
C
B
D
D
PE-2000
PE-2400
PE-3100
A
A

16
INCREASE
DEPTH
OPERATING TECHNIQUES
1. Before edging, water the area to soften the ground to make edging
easier.
2 Before edging, check the area and remove all obstacles and objects
that could be thrown.
3. Plan to edge regularly to make it easier to keep a neat edge and to
avoid having to make more than one pass.
NOTE
Blade depth may have to be adjusted due to differences in height
between the hard surface and the top of the grass.
WARNING DANGER
Never adjust blade height with engine running, otherwise serious
personal injury may result.
4. Adjust the blade's depth of cut to produce a fine cut between
sidewalk and grass using a minimum blade depth, usually with
about 1/2 in. of the blade into the ground.
5. Before edging, plan your direction of travel so that the unit will
always be positioned on your right side and so that you walk on a
hard surface whenever possible.
6. Hold edger as shown.
WARNING DANGER
Before edging, be sure to read and understand the entire
Operator's Manual to avoid the chance of serious injury.
7. When starting to edge, run the engine at full throttle, and lower the
blade gently into the ground, being careful not to hit the concrete
with the blade.
8. Don't force the blade. Move as quickly as the blade will allow.
WARNING DANGER
The complete unit, specifically the drive shaft assembly may
become very hot (too hot to touch) during use. Avoid contact
during and immediately after operation, otherwise serious personal
injurymayresult.
WHEEL WING
NUT
DECREASE
DEPTH
1/2in.

POWER EDGER
OPERATOR'SMANUAL 17
MAINTENANCE
Your ECHO edger is designed to provide many hours of trouble free service. Regular scheduled maintenance will help
your edger achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take your
unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOURSELF or have the
ECHO Dealer do it, each maintenance task has been graded. If the task is not listed, see your ECHO Dealer for repairs.
SKILL LEVEL
Level1= Easy to do. Most required tools come with unit.
Level2= Moderate difficulty. Somespecializedtoolsmay be required.
Level3= Experiencerequired.Specializedtoolsarerequired.ECHOrecommends
that the unit be returned to your ECHO dealer for service.
ECHO offers REPOWERTM Maintenance Kits and Parts to make your maintenance job easier. Just below each task
heading are listed the various part numbers required for that task. See your ECHO dealer for these parts.
MAINTENANCE INTERVALS
/TNENOPMOC METSYS ECNANETNIAM ERUDECORP
D'QER LLIKS LEVEL ROYLIAD EROFEB ESU
YREVE LEUFER
3SHTNOM 09RO SRUOH 6SHTNOM 072RO SRUOH
YLRAEY 006 SRUOH
serudecorPecnanetniaMrelaeDohcEdednemmoceR
troPtsuahxErednilyCnobraceD/naelC/tcepsnI 3C/I
serudecorPecnan
etniaMflesruoY-tI-oD
retliFriAecalpeR/naelC/tcepsnI 1C/I*R
ekohCnaelC/tcepsnI 2C/I
retliFleuFecalpeR/tcepsnI 1I*
R
skael,metsySleuFecalpeR/tcepsnI 1I*R/I
metsySgnilooCnaelC/tcepsnI 2C/I
rotserrAkrapSrelffuMecalpeR/tcepsnI 2C
/I*R/I
tfahSevirDesaerG 2)1(I
gnisuoHraeGesaerG 2)2(I
epoRretratSlioceRnaelC/tcepsnI 1*C/I*R/I
gulPkrapSnaelC/tcep
snI 2C/I*R
tnemecalpeRedalBecalpeR/tcepsnI 1II *R/I
stloB/stuN/swercSecalpeR/nethgiT/tcepsnI 1*R/I
SEDOCRETTELERUDECORPECNANETNIAM NAELC=C,ECALPER=R,TCEPSNI=I:
-ETONTNATROPMI deriuqerfoycneuqerfehtenimretedlliwecneirepxeruoydnaesulaut
cA.mumixameranwohsslavretniemiT
.ecnanetniam :SETONERUDECORPECNANETNIAM)1( OHCEylppA
®
EBUL
MT
.esufosruoh05yreve
)2( OHCEylppA
®
EBUL
MT
.esufosruoh52-51yreve
*..noitcepsnignirudraewroegamadfognidnifehtnodesaberaecalperotsnoitadnemmocerllA

18
AIR FILTER
Level1.
Tools required: Cleaningbrush,25or50mm(1or2in.)mediumbristle
paint brush.
Parts required: (PE-2000) 90008REPOWERAIR&FUELFILTERKIT
(PE-2400/3100) 90030REPOWERAIR&FUEL
FILTERKIT
1. Close choke (Cold Start Position). This prevents dirt from entering
the carburetor throat when the air filter is removed. Brush accumu-
lateddirtfromtheaircleanerarea.
2. Remove the air cleaner cover. Clean and inspect the element for
damage. If element is fuel soaked and very dirty, replace.
3. If element can be cleaned and reused, be certain it:
•still fits the cavity in the air cleaner cover.
•is installed with the original side out.
NOTE
Carburetor adjustment may be needed after air filter cleaning/
replacement. See Carburetor Adjustment Section.
FUEL FILTER
Level1.
Tools required: Fuellinehook,200-250mm(8-10in.)lengthofwire
with one end bent into a hook. Clean rag, funnel, and
an approved fuel container.
Parts required: (PE-2000) 90008REPOWERAIR&FUELFILTERKIT
(PE-2400/3100) 90030REPOWERAIR&FUEL
FILTERKIT
WARNING DANGER
FuelisVERYflammable.Useextremecarewhenmixing,storingor
handling.
1. Use a clean rag to remove loose dirt from around fuel cap and empty
fueltank.
2. Use the “fuel line hook” to pull the fuel line and filter from the tank.
3. Remove the filter from the line and install the new filter.
PE-2000
PE-2000

POWER EDGER
OPERATOR'SMANUAL 19
SPARK PLUG
Level2.
Tools required: Scrench (combination socket wrench and screwdriver)
and Feeler gauge (preferably a wire gauge), Soft Metal
Brush
Parts Required: SparkPlug,PE-2000 NGKBPM-7A
PE-2400,3100 NGKBPM-7Y
1. Remove spark plug and check for fouling, worn and rounded center
electrode.
2. Clean the plug or replace with a new one. DO NOT sand blast to
clean.Remainingsandwilldamageengine.
3. Adjust spark plug gap by bending outer electrode.
4. Tightensparkplugto145-155kg/cm(125-135in.lb.).
COOLING SYSTEMS CLEANING
Level3.
Tools required: CrossHeadScrewdriver,3 and4mmHexWrench,
CleaningBrush,25or50mm(1or2in.) mediumbristle
paint brush, Pointed Wood Stick.
Parts Required: None.
IMPORTANT
To maintain proper engine operating temperatures, cooling air must
pass freely through the cylinder fin area. This flow of air carries
combustion heat away from the engine.
Overheating and engine seizure can occur when:
• Air intakes are blocked, preventing cooling air from reaching the
cylinder.
• Dust and grass build up on the outside of the cylinder. This build up
insulates the engine and prevents the heat from leaving.
Removal of cooling passage blockages or cleaning of cooling fins is
considered “Normal Maintenance.” Any failure attributed to lack of
maintenance is not warranted.
1. Remove spark plug lead and throttle linkage end from the carburetor
swivel.
2. Remove the four screws that retain the cover. Two at the top of the
recoil starter, two on either side of the front. Lift the engine cover
(A) from the engine and lay to the front of the edger.
A
0.65 mm
(0.026 in.)

20
NOTE
The throttle linkage remains assembled to the cover and the spark
plugleadand grommetremaininstalled.
IMPORTANT
DO NOT use a metal scraper to remove dirt from the cylinder fins.
3. Use the wooden stick or brush to remove dirt from the cylinder fins.
4. Remove grass and leaves from the grid between the recoil starter
and fuel tank.
5. When installing the cover, be certain the tab of the metal deflector
shield is in the slot of the cover.
EXHAUST SYSTEM
Level2.
Tools Required: CrossHeadScrewdriver, 4mmHexWrench,Soft
Metal Brush
Parts Required: (PE-2000/2400)(1)14586652031SparkArrestor
Screen.
(PE-3100)(1)14590555730SparkArrestorScreen.
1. Remove engine cover (A). See "Cooling Systems Cleaning" for step
by step instructions.
2. Removemufflercover(B),screenholder(C)PE-2000/2400only,
gasket(D)andscreen(E)frommufflerbody.
3. Clean carbon deposits from screen and muffler components.
4. Replace screen if it is cracked, plugged or has holes burned
through.
5. Reassemble parts with new gasket in reverse order.
PE-2000
PE-2400
PE-3100
B
C
D
E
E
D
B