Echo Rapid Loader 99944200610 User manual

PAS RAPid LoAdeRTM TRiMMeR ATTAchMenT
oPeRAToR'SMAnuAL 1
PAS Rapid LoaderTM Trimmer Attachment
Operator's Manual
MODEL 99944200610
FOR MODELS: SRM-2100SB
SRM-2400SB
SRM-210SB/211SB/225SB
SRM-260SB/261SB
PAS-2100
PAS-2400
PAS-2601
PAS-210/211
PAS-225/225VP/225VPB
PAS-230/231
PAS-260/261
PAS-265/266
PAS-280
WARNING
Users of this equipment risk injury to themselves and others if the unit is used im-
properly and/or safety precautions are not followed. ECHO provides an operator’s
manual. It must be read and understood for proper and safe operation. Failure to
do so could result in serious injury.
X7702273505 X770000335
04/13

2
Copyright© 2013 By Echo, Incorporated
All Rights Reserved.
Table of ConTenTs
Introduction................................................................2
- The Operator's Manual .......................................2
Safety .........................................................................3
- Manual Safety Symbols and Important
Information .........................................................3
- International Symbols.........................................3
- Personal Condition and Safety Equipment ......... 4
- Equipment...........................................................6
Description.................................................................6
Contents .....................................................................7
Assembly....................................................................7
- Power Head Shaft/Attachment Lower
Shaft Assembly ...................................................8
- Plastic Shield Installation ...................................8
- Nylon Line Head Installation/Removal .............. 9
Operation....................................................................9
Maintenance...............................................................9
- Skill Levels .......................................................10
- Maintenance Intervals.......................................10
- Lubrication........................................................10
- Nylon Line Replacement .................................. 11
Storage ..................................................................... 11
Specications ........................................................... 11
Warranty Statement ......................................................12
Servicing Information ..............................................16
- Parts/Serial Number .........................................16
- Service ..............................................................16
- ECHO Consumer Product Support...................16
- Warranty Card................................................... 16
- Additional or Replacement Manuals ................16
Specications, descriptions and illustrative material in
this literature are as accurate as known at the time of
publication, but are subject to change without notice.
Illustrations may include optional equipment and acces-
sories, and may not include all standard equipment.
InTroduCTIon
Welcome to the ECHO family. is ECHO product was designed and manufactured to provide long life and on-the-job-
dependability. Read and understand this manual and the SAFETY MANUAL. You will nd both easy to use and full of
helpful operations tips and SAFETY messages.
The operaTor'smanual
Keep it in a safe place for future reference. Contains specications and
information for safety, operation, maintenance, storage, and assembly
specic to this product.
The safeTy manual
Keep it in a safe place for future reference. Explains possible hazards
and the measures you should take to insure safe operation.

PAS RAPid LoAdeRTM TRiMMeR ATTAchMenT
oPeRAToR'SMAnuAL 3
WARNING
Refer to your Pro Attachment Series or Split Boom Operator's Manual for correct engine fueling, starting and stop-
ping instructions.
manual safeTy symbols and ImporTanT InformaTIon
Throughout this manual and on the product itself, you will nd safety alerts and helpful, informational messages pre-
ceded by symbols or key words. The following is an explanation of those symbols and key words and what they mean to
you.
safeTy
InTernaTIonal symbols
CAUTION
The safety alert symbol accompanied by the word
“CAUTION” calls attention to an act or condition
which may lead to minor or moderate personal
injury if not avoided.
WARNING
The safety alert symbol accompanied by the word
“WARNING” calls attention to an act or condi-
tion which CAN lead to serious personal injury or
death if not avoided.
CIRCLE AND SLASH SYMBOL
This symbol means the specic action
shown is prohibited. Ignoring these prohi-
bitions can result in serious or fatal injury.
NOTE
This enclosed message provides tips for use, care and
maintenance of the unit.
IMPORTANT
The enclosed message provides information neces-
sary for the protection of the unit.
DANGER
The safety alert symbol accompanied by the word
“DANGER” calls attention to an act or condition
which WILL lead to serious personal injury or
death if not avoided.
Keep bystanders at least 15
meters (50 feet) away.
AVOID KICKOUT
Beware Thrown Objects
Wear Eye Protection
Symbol
description/application Symbol form/shape Symbol
description/application
Symbol form/shape
Symbol
description/application Symbol form/shape Symbol
description/application
Symbol form/shape
Read and under-
stand Operator's
Manual.
Wear eyes, ears
and head protec-
tion
Finger Severing
Safety/Alert
Plan retreat
path from falling
objects.
Wear slip resis-
tant foot wear.
Keep feet away
from blade
Thrown
objects
Wear hand and
foot protection
DO NOT USE
BLADES - Line
Head Only
Rotating
Cutting Attach-
ment
Do not operate closer
than 15 M (50 ft.) from
electrical hazards.
Keep bystanders
at least 15 meters
(50 feet) away.
Wear Face Shield
Keep bystanders and helpers
away 15 meters (50 feet) away.

4
Physical Condition
Your judgment and physical dexterity may not be good:
• if you are tired or sick,
• if you are taking medication,
• if you have taken alcohol or drugs.
Operate unit only if you are physically and mentally well.
Eye Protection
Wear eye protection that meets ANSI Z87.1 or CE re-
quirements whenever you operate the trimmer.
Hand Protection
Wear no-slip, heavy duty work gloves to improve your
grip on the Trimmer/Brush Cutter handles. Gloves also
reduce the transmission of machine vibration to your
hands.
Vibration and Cold
It is believed that a condition called Raynaud’s Phenomenon, which affects the ngers of certain individuals, may be
brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning sensa-
tions, followed by loss of color and numbness in the ngers. The following precautions are strongly recommended,
because the minimum exposure which might trigger the ailment is unknown.
• Keep your body warm, especially the head, neck, feet, ankles,
hands, and wrists.
• Maintain good blood circulation by performing vigorous arm
exercises during frequent work breaks, and also by not smoking.
• Limit the hours of operation. Try to ll each day with jobs where
operating the trimmer or other hand-held power equipment is not
required.
• If you experience discomfort, redness and swelling of the ngers
followed by whitening and loss of feeling, consult your physician
before further exposing yourself to cold and vibration.
personal CondITIon and safeTy equIpmenT
Proper Clothing
Wear snug tting, durable clothing;
• Pants should have long legs, shirts with long sleeves.
• DO NOT WEAR SHORTS,
• DO NOT WEAR TIES, SCARVES, JEWELRY,
or clothing with loose or hanging items that could
become entangled in moving parts or surrounding
growth.
Wear sturdy work shoes with nonskid soles;
• DO NOT WEAR OPEN TOED SHOES,
• DO NOT OPERATE UNIT BAREFOOTED.
Wear no-slip, heavy duty work gloves.
Keep long hair away from engine and air intake. Retain
hair with cap or net.
Hot Humid Weather
Heavy protective clothing can increase operator fatigue
which may lead to heat stroke. Schedule heavy work for
early morning or late afternoon hours when temperatures
are cooler.
WARNING
Users of this product risk injury to themselves and others if the unit is used improperly and/or safety precautions are
not followed. Proper clothing and safety gear must be worn when operating unit.

PAS RAPid LoAdeRTM TRiMMeR ATTAchMenT
oPeRAToR'SMAnuAL 5
Repetitive Stress Injuries
It is believed that overusing the muscles and tendons of the ngers, hands, arms and shoulders may cause soreness,
swelling, numbness, weakness, and extreme pain in those areas. Certain repetitive hand activities may put you at a high
risk for developing a Repetitive Stress Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome (CTS), which
could occur when your wrist swells and squeezes a vital nerve that runs through the area. Some believe that prolonged
exposure to vibration may contribute to CTS. CTS can cause severe pain for months or even years.
To reduce the risk of RSI/CTS, do the following:
• Avoid using your wrist in a bent, extended, or twisted position. In-
stead, try to maintain a straight wrist position. Also, when grasping,
use your whole hand, not just the thumb and index nger.
• Take periodic breaks to minimize repetition and rest your hands.
• Reduce the speed and force with which you do the repetitive
movement.
• Do exercises to strengthen the hand and arm muscles.
• Immediately stop using all power equipment and consult a doctor if
you feel tingling, numbness, or pain in the ngers, hands, wrists, or
arms. The sooner RSI/CTS is diagnosed, the more likely permanent
nerve and muscle damage can be prevented.
DANGER
Do not operate this product indoors or in inadequately ventilated
areas. Engine exhaust contains poisonous emissions and can cause
serious injury or death.
Read the Manuals
• Provide all users of this equipment with the Operator's Manual and
Safety Manual for instructions on Safe Operation.
Clear the Work Area
• Spectators and fellow workers must be warned, and children and
animals prevented from coming nearer than 15 m (50 ft.) while the
unit is in use.
Keep a Firm Grip
• Hold the front and rear handles with both hands, with thumbs and
ngers tightly encircling the handles.
Keep a Solid Stance
• Maintain footing and balance at all times. Do not stand on slippery,
uneven or unstable surfaces. Do not work in odd positions or on lad-
ders. Do not over reach.
Avoid Hot Surfaces
• During operation, the drive shaft housing, attachment bearing hous-
ing and mufer cover area may become very hot, too hot to touch.
Avoid contact during and immediately after operation.

6
5
12
3
4
desCrIpTIon
Locate this safety decal on your attachment. Make sure the decal is legible and that you understand and follow the
instructions on it. If it cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING
instructions for specic information.
WARNING
Moving parts can amputate ngers or cause severe injuries. Keep hands, clothing and loose objects away from all
openings.
• ALWAYS stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop
before removing obstructions, clearing debris, or servicing unit.
• DO NOT start or operate unit unless all guards and protective covers are properly assembled to unit.
• NEVER reach into any opening while the engine is running. Moving parts may not be visible through openings.
Shaft Decal
equIpmenT
WARNING
Use this attachment with ECHO approved models only. Serious injury may result from the use of this attachment
combined with a non approved ECHO product.
• Check unit for loose/missing nuts, bolts, and screws. Tighten and/or replace as needed.
• Inspect shield for damage and ensure that the cut-off knife is securely in place. Replace if either is damaged or miss-
ing.
• Check that the cutting attachment is rmly attached and in safe operating condition.
NOTE
ECHO, INC. will not be responsible for the failure of cutting devices, attachments or accessories which have not
been tested and approved by ECHO.

PAS RAPid LoAdeRTM TRiMMeR ATTAchMenT
oPeRAToR'SMAnuAL 7
assembly
WARNING
Do not perform maintenance or assembly procedures with engine
running.
Parts Required: PAS or SRM-SB Power Head w/Shaft & Coupling.
___ 1 - Pro Attachment SeriesTM Trimmer Attachment
___ 1 - Operator's Manual
___ 1 - Warranty Registration Card
___ 1 - Storage Hook Assembly
1. LOWER DRIVE SHAFT ASSEMBLY - Includes the Debris Shield Assembly, Gear Housing assembly, Flexible
Drive Cable, Rapid LoaderTM Head and Safety Decals.
2. FLEXIBLE DRIVE CABLE - Cable end ts into upper drive shaft coupler. Lubricate drive cable every 25 hours
with POWER BLENDXTM grease.
3. PLASTIC DEBRIS SHIELD ASSEMBLY - Shield assembly inclues the Cut-Off Knife. Helps protect the operator
by deecting debris produced during the trimming operation. This shield must be replaced with the steel shield for
blade use.
4. CUT-OFF KNIFE - Trims line to the correct length.
5. RAPID LOADERTM HEAD - Contains replaceable nylon trimming lines.
ConTenTs
The ECHO product you purchased has been factory pre-assembled for your convenience.
After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing
parts. Use the contents list to check for missing parts.

8
6. Rotate locator pin (A) 1/4 turn clockwise to engage lower shaft
hole. Insure locator pin is fully engaged by gently twisting
lower drive shaft. Locator pin (A) should snap ush in coupler.
Full engagement will prevent further shaft rotation.
7. Secure lower shaft assembly to coupler by tightening clamping
knob (D).
NOTE
Earlier model Power Heads may have shorter couplings. Short
couplings t ush to decal point (E). New couplings are 4-3/4 in.
long, and t ush to line (C).
NOTE
Lower bearing housing and head assembly must be in line with the
engine.
power head shafT/aTTaChmenT lower shafT assembly
1. Set Power Head/Shaft Assembly on a level surface.
2. Pull locator pin (A) and rotate counter clockwise 1/4 turn to lock
out position.
3. Remove vinyl cap from attachment drive shaft.
4. Remove cardboard spacer, if necessary.
5. Carefully t attachment lower drive shaft assembly into coupler (B)
to decal assembly line (C), making sure that the inner lower drive
shaft engages into the upper drive shaft mount.
plasTIC shIeld InsTallaTIon
(For Nylon Line Operation)
Parts Required: Plastic Shield, Shield Plate, three (3) 5mm x 16mm
screws.
NOTE
The plastic shield is for use with the Nylon Line Head only.
Install Metal Shield when using plastic or metal blades.
1. Place plastic shield on bottom of bearing housing ange.
2. Place shield plate on plastic shield, align holes. Install three (3)
screws from bottom through plate and shield into gear case.
A
B
D
E
C
D
C
A

PAS RAPid LoAdeRTM TRiMMeR ATTAchMenT
oPeRAToR'SMAnuAL 9
nylon lIne head InsTallaTIon/removal
1. Align hole in upper plate with notch in edge of gear housing and
insert head locking tool (A). Remove plastic sleeve from PTO
shaft.
2. Be sure upper plate (B) remains on PTO shaft.
3. Place line head onto PTO shaft, followed by large metal washer
(C).
4. Thread L.H. nut (D) on PTO shaft. Tighten securely.
5. Install new split pin (E).
6. Remove locking tool (A).
7. To remove line head, reverse assembly instructions.
C
Your ECHO trimmer is designed to provide many hours of trouble free service. Regular scheduled maintenance will
help your trimmer achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to
take your unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOUR-
SELF or have the ECHO Dealer do it, each maintenance task has been graded. If the task is not listed see your ECHO
dealer for repairs.
WARNING
Moving parts can amputate ngers or cause severe injuries. Keep hands, clothing and loose objects away from all
openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop
before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before performing service. Wear
gloves to protect hands from sharp edges and hot surfaces.
maInTenanCe
NOTE
Refer to the Grass Trimmer / Brush Cutter Safety Manual for proper and safe trimming techniques.
IMPORTANT
Never wear line shorter than 1-1/2 inch extension from head, otherwise overspeeding and engine damage may result.
operaTIon
WARNING
Moving parts can amputate ngers or cause severe injuries. Keep hands, clothing and loose objects away from all
openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop
before removing obstructions, clearing debris, or servicing unit.

10
lubrICaTIon
Level 1.
Parts Required: POWER BLENDXTM 8 oz. or Lithium
Base Grease.
Gear Housing
1. Clean all loose debris from gear box.
2. Remove plug (A) and check level of grease. Grease should ll gear
case to bottom of grease plug hole.
3. Add grease if necessary using manual grease gun or squeeze-type
tube. Do not use high pressure grease gun. DO NOT over-ll.
4. Install plug (A).
Drive Shaft (Lower)
1. Loosen two (2) screws (B) and remove center locating screw (C).
Pull gear box and shield from drive shaft housing.
2. Pull exible cable from the drive shaft housing, wipe clean and
re-coat with a thin coating [15 ml (1/2 oz.)] of LUBRICANTE®
ECHOTM.
3. Slide the exible cable back in the drive housing. DO NOT get
dirt on the ex cable.
4. Install the gear housing and shield assembly.
IMPORTANT
Flat edge of washers (D) must be against drive shaft.
maInTenanCe InTervals
A
B
C
D
skIll levels
Level 1= Easy to do. Common tools may be required.
Level 2 = Moderate difculty. Some specialized tools may be required.
Component Maintenance Procedure Skill Level Interval
Drive Shaft Grease 1 Every 25 hours of use [1]
Gear Housing Grease 1 Every 50 hours of use [1]
Screws/Nuts/Bolts Inspect/Tighten/Replace 1 Before Each Use
IMPORTANT - Time intervals shown are maximum. Actual use and your experience will determine the frequency
of required maintenance.
[1] Apply POWER BLENDXTM Grease.

PAS RAPid LoAdeRTM TRiMMeR ATTAchMenT
oPeRAToR'SMAnuAL 11
1. Insert pre-cut 204 mm (8 in.) length of nylon cut-
ting line (recommended sizes 2.4 mm [.095 in.]
to 3.9 mm [.155 in.]) through outside openings of
trimmer head. Minimum of 153mm (6 in.) of line
should extend from each opening. 3.9mm [.155 in.]
line not recommended for trimmers under 28cc.
Level 1.
Parts Required: Pre-cut Nylon Line
NOTE
Insert cutting line ends to center of head recess to insure easy
removal of used lines.
NOTICE:
Nylon line can damage plastic shield. When installing line seg-
ments, make sure line does not curve upward toward shield.
sTorage
Storage Hook Installation
1. Insert small end of hook into locating hole on attachment shaft.
2. Slide plastic cap onto end of attachment shaft.
Shaft Length ------------------------------------------------ 838 mm (33 in.)
Attachment Width ----------------------------------------- 178 mm (7 in.)
Attchment Height ------------------------------------------ 229 mm (9 in.)
Weight ------------------------------------------------------- 1.36 kg. (3.1 lb.)
Drive Shaft-------------------------------------------------- 6.35 mm (1/4 in.) Flex Shaft
Rotating Direction ----------------------------------------- Counter-clockwise viewed from the top
Cutter Head ------------------------------------------------- Rapid Loader TM head (2-lines) with .095 Cross Fire TM Line
speCIfICaTIons
PAS Rapid LoaderTM Attachment
MODELS REQUIRED LINE SIZES
SRM-2100SB
SRM-210SB/211SB/225SB .080 - .105 in.
PAS-210/211/2100
PAS-225/225VP/225VBP
PAS-230/231
SRM-2400SB .095 - .105 in.
PAS -2400
SRM-260SB/261SB
PAS-2601 .095 - .130 in.
PAS-260/261
PAS-265/266
PAS-280 .095 - .155 in.
nylon lIne replaCemenT

12
warranTy sTaTemenTs
ECHO LIMITED WARRANTY STATEMENT FOR
PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010
ECHO'S RESPONSIBILITY
ECHO Incorporated’s Limited Warranty, provides to the original purchaser that this ECHO product is free from defects in material and workmanship.
Under normal use and maintenance from date of purchase, ECHO agrees to repair or replace at ECHO’s discretion, any defective product
free of charge at any authorized ECHO servicing dealer within listed below application time periods, limitations and exclusions. THIS LIMITED
WARRANTY IS ONLY APPLICABLE TO ECHO PRODUCTS SOLD BY AUTHORIZED ECHO DEALERS. IT IS EXTENDED TO THE ORIGINAL
PURCHASER ONLY, AND IS NOT TRANSFERABLE TO SUBSEQUENT OWNERS EXCEPT FOR EMISSION RELATED PARTS. Repair
parts and accessories replaced under this warranty are warranted only for the balance of the original unit or accessory warranty period. Any
damage caused by improper installation or improper maintenance is not covered by this warranty. All parts or products replaced under warranty
become the property of ECHO, Inc. This warranty is separate from the Emission control warranty statement supplied with your new product.
Please consult the Emission Control Warranty Statement for details regarding emission related parts. For a list of Authorized ECHO Dealers
refer to WWW.ECHO-USA.COM or call 1-800-432-ECHO.
OWNER’S RESPONSIBILITY
To ensure trouble free warranty coverage it is important that you register your ECHO equipment on-line at WWW.ECHO-USA.COM-


The owner shall demonstrate reasonable care and use, and follow preventative maintenance, storage, fuel and oil usage as prescribed in the

dealer for warranty repairs (within the applicable warranty period), and arrange for pick-up or return of your unit after the repairs have been
made. For your nearest authorized ECHO servicing dealer, call ECHO’s Dealer Referral Center, at 1-800-432-ECHO or you can locate an ECHO
servicing dealer at WWW.ECHO-USA.COM. Should you require assistance or have questions concerning ECHO’s Warranty Statement, you
can contact our Consumer Product Support Department at 1-800-673-1558 or contact us through the web at WWW.ECHO-USA.COM.
PRODUCT WARRANTY PERIOD
RESIDENTIAL APPLICATION
 5 YEAR WARRANTY - All units for residential, or non-income producing use will be covered by this limited warranty for ve (5) years from
date of purchase.
EXCEPTIONS:
 
are warranted for the life* of the product on parts only.
 
producing use will be covered for failures due to defects in material or workmanship for a period of 60 days from original product
purchase date. Any misuse from contact with concrete, rocks, or other structures is not covered by this warranty.
 
manual for string head installation and maintenance instructions.
           

COMMERCIAL APPLICATION
 1 YEAR WARRANTY - All Chain Saws, QuikVent Saws, and Cut-Off Saws for commercial, institutional, agricultural, industrial, or income
producing use will be covered by this limited warranty for one (1) year from the date of purchase.
 2 YEAR WARRANTY - All other units for commercial, institutional, agricultural, industrial, or income producing use will be covered by this
limited warranty for two (2) years from the date of purchase.
EXCEPTIONS:
 
are warranted for the life* of the product on parts only.
 
agricultural, industrial, rental, or income producing will be covered for failures due to defects in material or workmanship for a period
of 30 days from original product purchase date. Any misuse from contact with concrete, rocks, or other structures is not covered by
this warranty.
 
manual for string head installation and maintenance instructions.
           

RENTAL APPLICATION - 90 DAYS WARRANTY

*  section of
this warranty statement for “Life”

PAS RAPid LoAdeRTM TRiMMeR ATTAchMenT
oPeRAToR'SMAnuAL 13
PURCHASED REPAIR PARTS, SHORT BLOCKS AND ACCESSORIES


ATTENTION TWO-STROKE ENGINE POWER PRODUCT OWNERS
This ECHO two-stroke engine power product is a quality-engineered unit which has been manufactured to exact tolerances to provide superior
performance. To help ensure the performance of the unit, it is required to use two-stroke oil which meets the ISO-L-EGD Standard per ISO/CD
13738 and JASO M345FD Standards. ECHO Power Blend™ Two-Stroke Oil 
L-EGD (ISO/CD 13738) and JASO M345FD Standards. The use of two-stroke oils designed for other applications, such as for outboard motors
or lawnmowers can result in severe engine damage, and will void your two-stroke engine limited warranty.
THIS WARRANTY DOES NOT COVER DAMAGE CAUSED BY:
 that do not meet the ISO-L-EGD (ISO/CD 13738) and JASO M345FD
Standards. Engine problems due to inadequate lubrication caused by failure to use an ISO-L-EGD compliant and JASO M345FD registered
oil, will void the two-stroke engine limited warranty.   meets the ISO-L-EGD and JASO M345FD
Standard. Emission related parts are covered for 5 years residential use or 2 years commercial use regardless of two-stroke oil used, per
the statement listed in the EPA or California Emission Defect Warranty Explanation.
 . Only use gasoline which
contains . Gasohol which contains a maximum
is also approved. The prescribed mixing ratio of gasoline to oil is listed on the ECHO oil label and covered in your operator’s manual.
 

engine speeds as listed in your operator’s manual.
 


of unauthorized attachments.
 
manual. Preventative maintenance as outlined in the operators manual is the customer’s responsibility.
 
warranty period.
 parts and other items are not warranted, including but not limited to: lubricants, starter cords, and engine tune-ups.
                     
Manuals.
 
screen.
 

with recommended grease or oil change intervals.
®beyond recommended capacity.

 
failure occur, the product should not be used, but delivered as is to an authorized ECHO servicing dealer.
It is a dealer’s and/or customer’s responsibility to complete and return the warranty registration card supplied with your ECHO product or by visiting
WWW.ECHO-USA.COM
ECHO servicing dealer for warranty service. Proof of purchase rests solely with the customer. Some states do not allow limitations on how long
an implied warranty lasts, so the above limitations may not apply to you. Some states do not allow the exclusion or limitation of incidental or

Incorporated, 400 Oakwood Rd., Lake Zurich, IL 60047.
DISCLAIMER OF IMPLIED WARRANTIES

OR USE and any implied warranty of MERCHANTABILITY


99922201032
11/18/2011

14
noTes

PAS RAPid LoAdeRTM TRiMMeR ATTAchMenT
oPeRAToR'SMAnuAL 15
noTes

DEALER?
Call
1-800-432-ECHO
or
www.echo-usa.com
ECHO, INCORPORATED
400 OAkwOOD ROAD
LAkE ZuRICH, IL 60047
www.echo-usa.com
CONSUMER PRODUCT
SUPPORT
1-800-673-1558
8:30 - 4:30 Mon - Fri C.S.T.
S43900001001/S43900999999
servICIng InformaTIon
parTs/serIal number
Genuine ECHO Parts and ECHO REPOWER™ Parts and Assemblies
for your ECHO products are available only from an Authorized ECHO
Dealer. When you do need to buy parts always have the Model Num-
ber, Type and Serial Number of the unit with you. You can nd these
numbers on the engine housing. For future reference, write them in the
space provided below.
Model No. _________________SN. ___________________
servICe
Service of this product during the warranty period must be performed
by an Authorized ECHO Service Dealer. For the name and address of
the Authorized ECHO Service Dealer nearest you, ask your retailer or
call: 1-800-432-ECHO (3246). Dealer information is also available on
our Web Site. When presenting your unit for Warranty service/repairs,
proof of purchase is required.
eCho Consumer produCT supporT
If you require assistance or have questions concerning the applica-
tion, operation or maintenance of this product you may call the ECHO
Consumer Product Support Department at 1-800-673-1558 from 8:30
am to 4:30 pm (Central Standard Time) Monday through Friday. Before
calling, please know the model and serial number of your unit.
warranTy regIsTraTIon
To ensure trouble free warranty coverage it is important that you regis-
ter your ECHO equipment on-line at www.echo-usa.com or by lling
out the warranty registration card supplied with your unit. Registering
your product conrms your warranty coverage and provides a direct
link between you and ECHO if we nd it necessary to contact you.
addITIonal or replaCemenT manuals
Replacement Operator, Safety Manuals, and Parts Catalogs are available from your ECHO dealer or at www.echo-
usa.com or by contacting ECHO Inc., 400 Oakwood Road, Lake Zurich, IL 60047 (800-673-1558). Always check the
ECHO Web Site for updated information.
Safety Videos are available from your Echo dealer. A $5.00 shipping charge will be required for each video.
99944200610