Echo SHC-261 User manual

SHAFT HEDGE CLIPPER
OPERATOR'SMANUAL 1
Shaft Hedge Clipper
Operator'sManual
MODEL: SHC-261
S/N 002001001 & Up
WARNING DANGER
X750001200
06/00
X7502094600
Readrulesforsafeoperationandinstructionscarefully. ECHOprovidesanOperator's
ManualandaSafetyManual. Bothmustbereadandunderstoodforproperandsafe
operation.Failuretodosocouldresultinserousinjury.

2
INTRODUCTION
Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-job-
dependability. Read and understand this manual and the SAFETY MANUAL you found in the same package. You will
find both easy to use and full of helpful operating tips and SAFETY messages.
WARNING DANGER
Read rules for safe operation and instructions carefully. ECHO provides an Operator's Manual and a Safety
Manual. Both must be read and understood for proper and safe operation.
THE OPERATOR'SMANUAL
contains specifications and information for operation, starting,
stopping, maintenance, storage and assembly specific to this product.
THE SAFETY MANUAL
explains possible hazards involved with the use of Hedge Clippers and
what measures you should take to make their use safer.
TABLE OF CONTENTS
Introduction ........................................................................ 2
- The Operator's Manual .............................................. 2
- The Safety manual ...................................................... 2
Manual Safety Symbols and Important Information ......... 3
Safety.................................................................................. 3
- Decals ......................................................................... 3
- International Symbols................................................. 4
- Equipment .................................................................. 5
- Fuel ............................................................................. 6
- Personal Condition and Safety Equipment................. 6
- Safe Operation ............................................................ 8
- ExtendedOperation/ExtremeConditions ................... 9
Description ....................................................................... 10
- Contents ................................................................... 10
- Emission Control ...................................................... 10
Specifications.................................................................... 13
Assembly.......................................................................... 14
- Gear Housing Assembly / Drive Shaft ..................... 14
- Drive Shaft Assembly / Power Head........................ 14
- Throttle Linkage and Ignition Leads ......................... 15
Pre-Operation ................................................................... 15
- Fuel ........................................................................... 15
- Equipment Check ..................................................... 17
- Determine Operation Area ....................................... 17
Operation.......................................................................... 18
- StartingColdEngine ................................................. 18
- StartingWarmEngine ............................................... 19
- StoppingEngine ........................................................ 20
Maintenance ..................................................................... 20
- SkillLevels................................................................ 20
- Maintenance Intervals .............................................. 21
- Air Filter ................................................................... 22
- Fuel Filter ................................................................. 22
- SparkPlug................................................................. 23
- CoolingSystemCleaning .......................................... 23
- Exhaust System ........................................................ 24
- Carburetor Adjustment............................................. 25
- Lubrication................................................................ 26
- SharpeningBlades..................................................... 28
Troubleshooting................................................................ 29
Storage .............................................................................. 30
ServicingInformation........................................................ 32
- Parts.......................................................................... 32
- Service ....................................................................... 32
- ECHO Consumer Product Support.......................... 32
- Warranty Card .......................................................... 32
- Additional or Replacement Manuals ........................ 32
- Manual Ordering Instructions .................................. 32
Specifications, descriptions and illustrative material in this
literature are as accurate as known at the time of publication,
but are subject to change without notice. Illustrations may
include optional equipment and accessories, and may not
include all standard equipment.
CopyRight© 2000 By Echo, Incorporated
All Rights Reserved.

SHAFT HEDGE CLIPPER
OPERATOR'SMANUAL 3
SAFETY
DECALS
Locate these safety decals on your unit. The complete unit illustration, found in the "DESCRIPTION" section, will help
you locate them. Make sure the decals are legible and that you understand and follow the instructions on them. If a decal
cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING instructions for specific
information.
MANUAL SAFETY SYMBOLS AND IMPORTANT INFORMATION
Throughout this manual and on the product itself, you will find safety
alerts and helpful, information messages preceded by symbols or key
words. The following is an explanation of those symbols and key
words and what they mean to you.
This symbol accompanied by the words WARNING
and DANGER calls attention to an act or condition that
can lead to serious personal injury to operator and
bystanders.
The circle with the slash symbol means whatever is
shown within the circle is prohibited.
IMPORTANT
The enclosed message provides
information necessary for the protection
of the unit.
NOTE
This enclosed message provides tips for
use, care and maintenance of the unit.
IMPORTANT
NOTE
WARNING DANGER
This unit is not designed to insulate against hazards associated with the contact of wires
carrying electrical current.
To avoid possible injury/death due to electrical shock or other hazards. DO NOT operate unit if
any wires (power, telephone, cable, etc.) are closer than 15 feet (4/5 meters minimum distance,
to any part of the unit or operator.
WARNING DANGER
This unit can be dangerous if used improperly. • Falling objects and/or blade
contact can cause serious injury to operator, helpers and bystanders. • Keep
helpers and bystanders at least 50 feet (15m) clear of operating area. • To reduce
injury risk, READ AND UNDERSTAND the operator's Manual, replacement copies
are available through your ECHO dealer. • Wear Protective clothing (head, hearing
and eye protection meeting ANSI standards) specified in the Operator's Manual.
• STOP engine before making repairs or blade adjustments. • Keep hand away from
blade. P/N 89018721460

4
Shaft Decal
Spanish Decal
WARNING DANGER
Thisunitcanbedangerous
and cause serious injury if
improperlyused.to reduce
injury risk to operator,
helpers and bystanders,
read and understand the
Operator's and Safety
Manuals,whichareprovided
in Spanish.
ADVERTENCIA PELIGRO English Translation
Estaunidad
puedeser
peligrosay
producirlesiones
personales
gravessino se
usaenformaadecuada.Para
reducirelriesgo de
lesionarse,losoperadores,
los ayudantes y los
espectadoresdebenleery
comprenderelManualDel
OperadorylosManuales De
Seguridadqueseentregan
escritos en español.
INTERNATIONALSYMBOLS
SYMBOL
DESCRIPTION/APPLICATION SYMBOL FORM/
SHAPE SYMBOL
DESCRIPTION/APPLICATION
SYMBOL FORM/
SHAPE
Hot
Surface
Carburetor
adjustment
-Idlespeed
Carburetor
adjustment
- High speed
mixture
SYMBOL
DESCRIPTION/APPLICATION SYMBOL FORM/
SHAPE SYMBOL
DESCRIPTION/APPLICATION
SYMBOL FORM/
SHAPE
Readand
understand
Operator'sManual.
Weareyes,ears
andhead
protection Emergencystop
Fueland oil
mixture
FingerSevering
Carburetor
adjustment
-Low speed
mixture
Safety/Alert
Do not operate
closerthan 15M
(50 ft.) from
electrical
hazards.
Keepbystanders
atleast15meters
(50feet)away.
Planretreatpath
from falling
objects.
Wearhand
protection.Use
twohanded.
DONOTsmoke
nearfuel.
DONOT allow
flamesorsparks
nearfuel.
Wearslip
resistantfoot
wear.
Enginechoke
control. Ignition ON/OFF
Primerbulb
Avoidallpower
lines.This unitis
notinsulated
againstelectrical
current.

SHAFT HEDGE CLIPPER
OPERATOR'SMANUAL 5
EQUIPMENT
Before operation a complete check of the unit must be performed;
• Check unit for loose/missing nuts, bolts and screws. Tighten
and/or replace as needed.
• Inspect fuel lines, tank and area around carburetor for fuel leaks. DO
NOT operate unit if leaks are found.
• Check that the blade assembly is firmly attached and in safe operating
condition. Dull, loose or damaged blades should not be used.
• Do not use shaft hedge clipper if any part is missing or damaged.
• Have repairs done only by an authorized ECHO Service Dealer.
• Do not use any attachment, accessory or replacement part unless it is
recommended in this Operator's Manual.
Spark Arrestor - Catalytic Muffler / Muffler
• The muffler or catalytic muffler controls the exhaust noise and
emissions. The spark arrestor screen prevents hot, glowing particles
of carbon from leaving the muffler. Make sure the spark arrestor
screen is in good repair and properly seated in the muffler. Keep
exhaust area clear of flammable debris. Avoid contact during and
immediatelyafteroperation.

6
FUEL
WARNING DANGER
FuelisVERYflammable.Useextremecarewhenmixing,storingor
handling, otherwise serious personal injury may result.
• Use an approved fuel container.
• DONOTsmokenearfuel.
• DONOTallow flamesorsparks nearfuel.
• Fuel tanks/cans may be under pressure. Always loosen fuel caps
slowly allowing pressure to equalize.
• NEVERrefuelaunitwhentheengineis HOT!
• NEVERrefuela unitwiththe enginerunning.
• DONOTfillfueltanksindoors.ALWAYS fill fuel tanks outdoors
over bare ground.
• Securely tighten fuel cap after refueling.
• Inspect for fuel leakage. If fuel leakage is found, do not start or
operate unit until leakage is repaired.
IMPORTANT
Spilled fuel is a leading cause of hydrocarbon emissions. Some
states may require the use of automatic fuel shut-off containers to
reducefuelspillage.ContactyourECHO dealer for ordering
information.
After Refueling;
• Wipe any spilled fuel from the unit.
• Move at least 3 M (10 ft.) from refueling location before starting.
After Use;
• DO NOT store a unit with fuel in its tank. Leaks can occur. Return
unused fuel to an approved fuel storage container.
3 M (10 FT.)
PERSONAL CONDITION AND SAFETY EQUIPMENT
WARNING DANGER
Hedge Clipper users risk injury to themselves and others if the shaft hedge clipper is used improperly and or safety
precautions are not followed. Proper clothing and safety gear must be worn when operating a shaft hedge clipper.

SHAFT HEDGE CLIPPER
OPERATOR'SMANUAL 7
Physical Condition
Your judgment and physical dexterity may not be good:
• if you are tired or sick,
•ifyouaretakingmedication,
• if you have taken alcohol or drugs.
Operate unit only if you are physically and mentally well.
Eye Protection
Wear eye protection that meets ANSI Z87.1 or CE requirements when-
ever you operate the unit.
Face & Head Protection
Whentrimmingoverhead, wear head protectionmeetingANSIZ89.1
withafullface shield.
Hand Protection
Wear no-slip, heavy duty work gloves to improve your grip on the
unit handles. Gloves also reduce the transmission of machine vibration
to your hands.
Hearing Protection
Wear hearing protection. ECHO recommends wearing hearing protec-
tion whenever unit is used.
Proper Clothing
Wear snug fitting, durable clothing;
• Pants should have long legs, shirts with long sleeves.
• DONOTWEARSHORTS,
• DONOTWEARTIES,SCARVES,JEWELRY.
Wear sturdy work shoes with non-skid soles;
• DONOTWEAROPENTOEDSHOES,
• DONOTOPERATEUNITBAREFOOTED.
Hot Humid Weather
Heavy protective clothing can increase operator fatigue which may lead
to heat stroke. Schedule heavy work for early morning or late afternoon
hours when temperatures are cooler.

8
SAFE OPERATION
Determine Operation Area
• Provide all operators of this equipment with the Operator's Manuals
and instructions for safe operation.
• Review the area to be trimmed. Look for hazards that could contribute
to unsafe conditions. DO NOT operate unit if any wires (power,
telephone, cable, etc.) are closer than 4.5 M (15 ft.) to any part of the
operator or unit.
• Spectators and fellow workers must be warned, and children and
animalspreventedfromcoming nearer than 15M(50ft.) while the
Hedge Clipper is in use.
Operation
WARNING DANGER
Do not operate this product indoors or in inadequately ventilated
areas. Engine exhaust contains poisonous emissions and can cause
serious injury or death.
UseProperClothing&Equipment
• Before starting the unit, equip yourself and any other person
working within the 15 M (50 ft.) Safety Zone with the required
Protective Equipment and clothing.
AvoidHotSurfaces
• During operation, the complete unit, especially the power head,
muffler cover area and gear box may become very hot. Avoid contact
during and immediately after operation. Always keep exhaust area
clearofflammabledebris.
KeepAFirmGrip
• Hold the front and rear handles with both hands with thumbs and
fingers tightly encircling the handles.
KeepASolidStance
• Maintain footing and balance at all times. Do not stand on
slippery, uneven or unstable surfaces. Do not work in odd
positions or on ladders. Do not over reach.

SHAFT HEDGE CLIPPER
OPERATOR'SMANUAL 9
EXTENDED OPERATION/EXTREME CONDITIONS
Vibration and Cold
It is believed that a condition called Raynaud’s Phenomenon, which
affects the fingers of certain individuals may be brought about by
exposure to vibration and cold. Exposure to vibration and cold may
cause tingling and burning sensations followed by loss of color and
numbness in the fingers. The following precautions are strongly
recommendedbecausethe minimum exposurewhichmighttrigger the
ailmentisunknown.
• Keep your body warm, especially the head, neck, feet, ankles, hands
and wrists.
• Maintain good blood circulation by performing vigorous arm
exercises during frequent work breaks and also by not smoking.
• Limit the hours of operation. Try to fill each day with jobs where
operating the trimmer or other hand-held power equipment is not
required.
• If you experience discomfort, redness and swelling of the fingers
followed by whitening and loss of feeling, consult your physician
before further exposing yourself to cold and vibration.
Repetitive Stress Injuries
It is believed that overusing the muscles and tendons of the fingers,
hands, arms and shoulders may cause soreness, swelling, numbness,
weakness and extreme pain in those areas. Certain repetitive hand
activities may put you at a high risk for developing a Repetitive Stress
Injury(RSI).AnextremeRSIconditionisCarpalTunnelSyndrome
(CTS), which could occur when your wrist swells and squeezes a vital
nerve that runs through the area. Some believe that prolonged exposure
to vibration may contribute to CTS. CTS can cause severe pain for
months or even years.
To reduce the risk of RSI/CTS, do the following:
• Avoid using your wrist in a bent, extended or twisted position.
Instead try to maintain a straight wrist position. Also, when grasping,
use your whole hand, not just the thumb and index finger.
• Take periodic breaks to minimize repetition and rest your hands.
• Reduce the speed and force with which you do the repetitive
movement.
• Do exercises to strengthen the hand and arm muscles.
• Immediately stop using all power equipment and consult a doctor if
you feel tingling, numbness or pain in the fingers, hands, wrists or
arms. The sooner RSI/CTS is diagnosed, the more likely permanent
nerve and muscle damage can be prevented.

10
DESCRIPTION
The ECHO product you have purchased has been factory pre-assembled for your convenience. Due to packaging
restrictions, some assembly of the SHC-261 is required.
After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing
parts. Use the contents list to check for missing parts.
CONTENTS LIST
__ 1- PowerHead
__ 1 - Gear Case Assembly
__ 1 - Drive Shaft Assembly
__ 1 - Operator's Manual
__ 1 - Hedge Clipper Safety Manual
__ 1 - Warranty Statement
__ 1 - Warranty Registration Card
__ 1-BladeCover
__ 1- 2-StrokeOilSample,2.6oz.
__ 1-Scrench17x19
__ 1-4mmHexWrench
__ 1-8mm/10mmWrench
IMPORTANTENGINEINFORMATION
ENGINE FAMILY: YEHXS.0254RA
DISPLACEMENT: 25.4 CC
THIS ENGINE MEETS U.S. EPA PH1 AND 2000 AND
LATER CALIFORNIA EMISSION REGULATIONS FOR
S.O.R.E. REFER TO OWNER'S MANUAL FOR
MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS.
AnEmission Control Label is located on the engine. (This is an
EXAMPLEONLY,informationonlabelvariesbyengineFAMILY).
AIRINDEXTAG
TheAirIndexTagindicates,forpurposes
ofconsumer awareness,howthisproduct's
emissionscomparetothestandardsenacted
bytheCaliforniaAirResourcesBoard.
PRODUCT EMISSION DURABILITY
The300houremissiondurabilityperiodisthetimespanselectedbythemanufacturercertifyingtheengine
emissionsoutputmeetsapplicableCaliforniaemissionsregulations,providedthatapprovedmaintenanceproce-
duresarefollowedaslistedintheMaintenanceSectionofthismanual.
EMISSION CONTROL
California Tier 2
The emission control system for these engines are
EM(EngineModification).

SHAFT HEDGE CLIPPER
OPERATOR'SMANUAL 11
14
15
16
17
18
19
20
12
3
4
5
6
7
8
9
10
1
11
13
2
21

12
1. OPERATOR'SMANUAL-Includedin plastic bag (co-pack).Read beforeoperationand keep in a safeplacefor
future reference, i.e., operation, maintenance, storage and specifications.
2. SAFETYMANUAL-(P/N89857020060)Includedinplasticbag(co-pack).Readbeforeoperationandkeepinasafe
place for future reference, i.e., safe operating techniques.
3. POWERHEAD-IncludestheEngine,Clutch,FuelSystem,IgnitionSystemandRecoilStarter.
4. GRIP,RIGHTHANDREAR-Cushionedgripforrighthand.
5. "STOPSWITCH" mounted on top of the Throttle Trigger Housing. Move switch FORWARD to RUN, BACK to
STOP.
6. GRIP,LEFTHAND,FRONT-CushionedgripforLeftHand.
7. DRIVESHAFTASSEMBLY-ContainstheFlexibleDriveCable.
8. BLADES - Double reciprocating blades mounted to a blade support bar. Double sided blades, are capable of
cutting on either side of the blade.
9. GEARHOUSINGASSEMBLY-Gearhousingassemblyfixedstraightextension.
10. THROTTLETRIGGER-Springloadedtoreturntoidlewhenreleased.Duringacceleration,depressgraduallyfor
best operating technique.
11. BLADE COVER - Used to cover blade during transport and storage. Remove blade cover before using unit.
12. SPARKPLUG-Providessparktoignitefuelmixture.
13. ARM REST - Provides arm rest during operation and protects arm from the hot engine.
14. SPARKARRESTOR-CATALYTICMUFFLER/MUFFLER-Themufflerorcatalyticmufflercontrolsexhaustnoise
and emission. The spark arrestor screen prevents hot, glowing particles of carbon from leaving the muffler. Keep
exhaustareaclearofflammabledebris.
15. FUELTANK-Containsfuelandfuelfilter.
16. RECOILSTARTERHANDLE-Pullhandleslowlyuntilstarterengages,thenquicklyandfirmly. Whenengine
starts, return handle slowly. DO NOT let handle snap back or damage to unit will occur.
17. FUELTANKCAP-Coversandsealsfueltankopening.
18. PRIMERBULB-Pumpingprimerbulbbeforestartingenginedrawsfreshfuelfrom thefuel tankprimingthe
carburetor for starting. Pump primer bulb until fuel is visible and flows freely in the clear fuel tank return line. Pump
bulb an additional 4 or 5 times.
19. AIRCLEANER-Containsreplaceablefilterelement.
20. CHOKE CONTROL - Located on the top of the air cleaner housing. Move the lever to "COLD START" to close the
choke for Cold Starting. Move lever to "RUN" position after engine fires.
21. HEDGECLIPPERSAFETYVIDEO-P/N99922202800(NotincludedwithunitandEnglishversiononly)isavailable
for your review and purchase at a cost of $5.00 from ECHO, INC. or any authorized ECHO dealer. The video over-
views safety precautions and proper operating techniques provided in detail in the Safety Manual, and is supple-
mental to the Safety Manual. Read and understand the Safety Manual for complete information on safe operation.

SHAFT HEDGE CLIPPER
OPERATOR'SMANUAL 13
SPECIFICATIONS
MODEL SHC-261
Length 2230 mm (87.8 in.)
Width 250 mm (9.84 in.)
Height 250 mm (9.84 in.)
Weight (dry) 6.0 kg (13.2 lb.)
Engine Type Air cooled, two-stroke, single cylinder gasoline engine
Bore 34.0 mm (1.34 in.)
Stroke 28.0 mm (1.10 in.)
Displacement 25.4 cc (1.55 cu. in.)
Exhaust Spark Arrestor Muffler w/Catalyst
Carburetor Walbro diaphragm model WYJ w/primer pump
Ignition System Flywheel magneto, capacitor discharge
Spark Plug NGK BPM-7Y (Gap 0.65 mm (0.026 in.)
Fuel Mixed (Gasoline and Two-stroke Oil)
Fuel/Oil Ratio 50:1 ECHO High Performance, two-stroke air cooled engine oil
Gasoline 89 Octane unleaded. DO NOT use fuel containing methyl alcohol, more than
10% ethyl alcohol or 15% MTBE.
Oil 50:1 ECHO High Performance, two-stroke air cooled engine oil
Fuel Tank Capacity 0.58 lit. (19.6 US fl. oz.)
Recoil Starter System Automatic Recoil Starter
Clutch Centrifugal Type
Gear Case Ratio 6.36:1 Reduction
Cutter
Length
Pitch
Double Reciprocating Blade - Double Edge
575 mm (22.6 in.)
35 mm (1.4 in.)
Idle Speed 2800 - 3200 RPM
Wide Open Throttle Speed (W.O.T.) 8000 - 10000 RPM

14
ASSEMBLY
GEAR HOUSING ASSEMBLY / DRIVE SHAFT
ToolsRequired: 4mmHexWrench,Screwdriver
Parts Required: Power Head/Drive Shaft Assembly and Gear Housing
Assembly.
NOTE
Hedge Clipper Blades are very sharp. Wear gloves to protect
hands.
1. Slide the Gear Housing Assembly on the Drive Shaft. Be certain
theFlexDriveShaftengagesthehole in Driver Gear.
2. Align the locating screw (A) with the locating hole (B) in the Drive
Shaft Housing, tighten screw (A) and clamping screws (C).
DRIVE SHAFT ASSEMBLY /POWER HEAD
Tools Required: 4mmHexWrench
Parts Required: PowerHead,DriveShaftAssembly
1. Loosen, the bolt (A) at engine drive shaft clamp.
2. Carefully fit drive shaft assembly to engine making sure that
inner drive shaft engages into clutch mount.
NOTE
Lower gear housing cutter head assembly must be in line with the
engine.
3. Turn drive shaft housing so that center line of housing is midway
between the two arrows on shaft.
4. Tighten bolt (A).
A
A

SHAFT HEDGE CLIPPER
OPERATOR'SMANUAL 15
THROTTLE LINKAGE AND IGNITION LEADS
1. Close choke and remove air filtercover.
2. Loosen nut (A) and place threaded end of throttle linkage in
bracket slot. Finger tighten nut (A).
3. Place inner cable in slot of carburetor swivel (B) and tighten nut
(A).
4. Check throttle for freedom of movement and that wide open throttle
/ low idle extremes are adjusted properly. If adjustment cannot be
achieved with adjusting nuts, consult with your Echo Dealer for
correct adjustment procedure.
5. Connect ignition stop leads (C) and (D).
6. Bundle and secure ignition leads against engine housing with clip
(E).
7. Install airfilterand cover.
PRE-OPERATION
FUEL
Fuel Requirements
Gasoline - Use 89 Octane [ ] (mid grade or higher) gasoline or
gasohol known to be good quality. Gasohol may contain up to 10%
Ethyl(grain)alcoholor15%MTBE(methyltertiary-butylether).
Gasohol containing methyl (wood) alcohol is NOT approved.
TwoStrokeOil-Atwo-strokeengineoilmeetingISO-L-EGD (ISO/CD
13738)andJASO FC standards,mustbeused. Echo brandPremium50:1
oil meets these standards. Engine problems due to inadequate lubrica-
tioncausedby failure tousean ISO-L-EGD andJASOFCcertified oil,
suchasEchoPremium50:1Two-strokeOil,willvoidthetwo-stroke
engine warranty. (Emission related parts only are covered for two
years, regardless of two-stroke oil used, per the statement listed in the
CaliforniaEmissionDefectWarrantyExplanation.)
Mixing- Follow directions on the oil container.
R + M
2
C
AB
D
E

16
Handling Fuel
WARNING DANGER
FuelisVERYflammable.Useextremecarewhenmixing,storingor
handling, or serious personal injury may result.
• Use an approved fuel container.
• DONOTsmokenearfuel.
• DONOTallow flamesorsparks nearfuel.
• Fuel tanks/cans may be under pressure. Always loosen fuel caps
slowly allowing pressure to equalize.
• NEVERrefuelaunitwhentheengineis HOT!
• NEVERrefuela unitwiththe enginerunning.
• DONOTfillfueltanksindoors.ALWAYS fill fuel tanks outdoors
over bare ground.
• Securely tighten fuel cap after refueling.
• Inspect for fuel leakage. If fuel leakage is found, do not start or
operate unit until leakage is repaired.
IMPORTANT
Spilled fuel is a leading cause of hydrocarbon emissions. Some
states may require the use of automatic fuel shut-off containers to
reducefuelspillage.ContactyourECHO dealer for ordering
information.
After refueling;
• Wipe any spilled fuel from the unit.
• Move at least 3 M (10 ft.) from refueling location before starting the
engine.
After use;
• DO NOT store a unit with fuel in its tank. Leaks can occur.
Return unused fuel to an approved fuel storage container.
Storage -
Fuel storage laws vary by locality. Contact your local government for
the laws affecting your area. As a precaution, store fuel in an approved,
air tight container. Store in a well ventilated, unoccupied building, away
from sparks and flames. Do not store fuel longer than 30 days.
IMPORTANT
Stored fuel ages. Do not mix more fuel than you expect to use in
thirty (30) days, ninety (90) days when a fuel stabilizer is added.
IMPORTANT
Stored two-stroke fuel may separate. ALWAYS shake fuel
container thoroughly before each use.
SMTWTF S
1234567
8 9 10 1112 13 14
1516 17 1819 20 21
2223 24 2526 27 28
2930 31
3 M (10 FT.)

SHAFT HEDGE CLIPPER
OPERATOR'SMANUAL 17
EQUIPMENT CHECK
Before operation a complete check of the unit must be performed;
• Check unit for loose/missing nuts, bolts and screws. Tighten and/or
replace as needed.
• Inspect fuel lines, tank and area around carburetor for fuel leaks.
DO NOT operate unit if leaks are found.
• Check that the blade assembly is firmly attached and in safe operating
condition. Dull, loose or damaged blades should not be used.
DETERMINE OPERATION AREA
• Review the area to be trimmed. Look for hazards that could contribute
to unsafe conditions. DO NOT operate unit if any wires (power,
telephone, cable, etc.) are closer than 4.5 M (15 ft.) to any part of the
operator or unit.
• Spectators and fellow workers must be warned, and children and
animalspreventedfromcoming nearer than 15M(50ft.) while the
trimmerisinuse.

18
OPERATION
WARNING DANGER
Do not operate this product indoors or in inadequately ventilated
areas. Engine exhaust contains poisonous emissions which can
cause serious injury or death.
• Provide all operators of this equipment with the Operator's Manual
and instructions for safe operation.
• Before starting the unit, equip yourself and any other person working
within the 15 M (50 ft.) Safety Zone with the required Protective
Equipment and clothing. (Refer to Operator Safety)
• During operation, the complete unit, especially the power head,
muffler cover area and gear box may become very hot. Avoid contact
during and immediately after operation. Always keep exhaust area
clearofflammabledebris.
STARTING COLD ENGINE
WARNING DANGER
The blades should not move at idle. If blades move, readjust
carburetor according to "Carburetor Adjustment" instructions in
this manual or see your ECHO Dealer, otherwise serious personal
injurymayresult.
1. Stop Switch - Start/Run.
Move stop switch button (A) forward away from the STOP
position.
2. Close Choke - Cold Start.
Move choke lever (B) to Cold Start Position.
3. PrimerBulb-Pumpprimerbulb(C) until fuel is visible and flows
freely in the clear fuel tank return line. Pump bulb an additional 4 or
5times.
C
B
A

SHAFT HEDGE CLIPPER
OPERATOR'SMANUAL 19
4. Start - Pull Rope.
Lay the shaft hedge clipper on a flat clear area and pull the recoil
starter handle (D) until engine fires.
5. Open Choke - Run.
Move the choke lever to the OPEN - RUN position. Restart engine
if necessary and allow to warm up running at idle for several
minutes.
STARTING WARM ENGINE
The starting procedure is the same as Cold Start except DO NOT close
the choke.
NOTE
If engine does not start after 5 pulls, use Cold Start Procedure.
WARNING DANGER
When engine starts, the cutting attachment may move even with
the throttle trigger in idle (released) position.
1. Stop Switch - Start/Run. Move stop switch button (A) away from
the STOP position.
2. Primer Bulb - Pump primer bulb until fuel is visible and flows freely
in the clear fuel tank return line. Pump bulb an additional 4 or 5
times.
3. Start - Pull Rope. Lay the shaft hedge clipper on a flat clear area
and pull the recoil starter handle (D) until the engine fires.
D
D
C
A

20
STOPPING ENGINE
1. Release Throttle. Allow engine to idle for a minute.
2. Stop Switch - Stop. Move stop switch button (A) backward to
STOPposition.
WARNING DANGER
If engine does not stop when stop switch is moved to STOP
position, close choke - COLD START position - to stall engine.
Have your ECHO dealer repair stop switch before using shaft
hedge clipper again.
NOTE
Refer to the Hedge Clipper Safety Manual for proper and safe hedge
clippingoperation.
A
MAINTENANCE
Your ECHO product is designed to provide many hours of trouble free service. Regular scheduled maintenance will help
achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take your unit to an
ECHOServiceDealerformaintenance. Tohelpyoudecidewhether youwanttoDO-IT-YOURSELForhavetheECHO
Dealer do it, each maintenance task has been graded. If the task is not listed, see your ECHO Dealer for repairs.
SKILL LEVEL
Level1= Easy to do. Most required tools come with unit.
Level2= Moderate difficulty. Some specialized tools may be required.
Level3= Experiencerequired.Specializedtoolsarerequired.ECHOrecommends
that the unit be returned to your ECHO dealer for service.
ECHO offers REPOWERTM Maintenance Kits and Parts to make your maintenance job easier. Just below each task
heading are listed the various part numbers required for that task. See your ECHO dealer for these parts.