EchoStar DVR-5000 HDD Viaccess Manual

Service Letter
EchoNAV software version 2.2
EchoNAV User Interface
for Digital Satellite Receivers
HDD
Printed on recycled paper

Issue: echonav_hdd_sl_22a_us
© 2002 EchoStar International Corporation - The Netherlands
We encourage you to express your thoughts on this service letter.
Please send your comments to:
EchoStar International Corporation
Technical Publications Department
Schuilenburglaan 5a
7604 BJ Almelo
The Netherlands

Preface
EchoNAV 2.2 Page I
© 2002 EchoStar International Corporation
All rights reserved
PREFACE
1. DEAR CUSTOMER
This service letter introduces version 2.2 for the EchoNAV user interface which supersedes
the previous service letter(s). For your convenience the highlights of the previous software
are also given.
THE HIGHLIGHTS FOR VERSION 2.2
■Two menu languages added;
■Revised help lines and related translations;
■Revised subtitle behaviour;
■Russian and Greek subtitle languages added;
■Multilingual EPG language support added;
■Revised conditional access to support smartcards type PC2.4;
■Revised channel numbering for Current SAT list;
■New installation menus added for multiple LNB support;
■Revised Add SAT, TP and PID menus;
■Pre-defined LNB (LO 10,700) added to LNB list;
■User LNB settings menu are moved to the Advanced mode;
■New option to add satellite or transponder during initial installation setup added;
■OTA service added on ASTRA1, 19.2 East.
■DVR timer modified to allow for recording a relative time block.
■Updated satellite/transponder database
THE HIGHLIGHTS FOR PREVIOUS VERSION 2.0
■Six menu languages added;
■Group and Sort behaviour revised to remember the last setting;
■Extended channel information available with i-key;
■Move function extended with recall option;
■Edit functions, Move, Lock and Delete separated;
■Save changes pop-up menu added.
■Updated satellite/transponder database
DVR-7000 HDD ONLY
■Photo album added;
■New MP3Loader made available with embedded BackgroundLoader and PhotoLoader;
■Installation menu added for Set East and West Limit;
■Improved positioner behaviour.
2. INTENDED USE
This service letter is intended for anyone who uses an EchoStar satellite receiver with an
EchoNAv user interface. It can be used by both first-time and experienced users who want to
install, use and maintain their receiver.
This service letter is applicable for the Digital Satellite Receiver with Hard Disk:
■DVR-7000 HDD Viaccess;
■DVR-7000 HDD;
■DVR-5000 HDD Viaccess;
■DVR-5000 HDD.
This service letter is divided into separate sections and chapters for easy reference to the
applicable chapters of your user manual. Please keep this service letter next to your user
manual for future reference.

Preface
Page II EchoStar International Corporation
© 2002 EchoStar International Corporation
All rights reserved
3. DISCLAIMER
SATELLITE RECEIVER
EchoStar International Corporation has done everything to the best of her abilities, to supply
you with a satellite receiver built to the most up-to-date software and hardware. EchoStar
International Corporation makes no warranties with respect to the reception of the channels
provided by the broadcast service providers and specifically disclaims any implied warranties
of merchantability or fitness for any particular purpose.
EchoStar International Corporation reserves the right, for whatever reason, to revise, change
or modify the hard- and software of the satellite receiver without the obligation to notify or
warrant any person or organization of such change. Therefore, please visit our website, on a
regular basis, for the latest information available.
SOFTWARE DOWNLOADS
EchoStar International Corporation will do everything to the best of her abilities, to supply you
with software updates to keep your receiver as up-to-date as technically possible. EchoStar
International Corporation makes no warranties with respect to the use of the supplied
software downloads and specifically disclaims any implied warranties of merchantability or
fitness for any particular purpose.
EchoStar International Corporation reserves the right, for whatever reason, to revise, change
or modify the software that can be used by your satellite receiver without the obligation to
notify or warrant any person or organization of such change. Therefore, please visit our
website, on a regular basis, for the latest software available.
SERVICE LETTER
EchoStar International Corporation has done everything to the best of her abilities, to supply
you with the most up-to-date information. EchoStar International Corporation makes no
warranties with respect to the information provided by this service letter and specifically
disclaims any implied warranties of merchantability or fitness for any particular purpose. The
information provided is meant as a guideline for the use and maintenance of the receiver.
EchoStar International Corporation reserves the right to right, for whatever reason, change or
translate this service letter without the obligation to notify any person or organization of such
change. Therefore, please visit our website, on a regular basis, for the latest information
available.

Preface
EchoNAV 2.2 Page III
© 2002 EchoStar International Corporation
All rights reserved
TABLE OF CONTENTS
Preface
1 DEAR CUSTOMER I
2 INTENDED USE I
3DISCLAIMER II
Installation
1 TO SETUP YOUR RECEIVER FOR THE FIRST TIME 3-1
2 ADVANCED MODE (MULTIPLE LNB SUPPORT) 3-7
Familiarization
1 ECHONAV 2.2 4-1
2 THE ECHONAV INSTALLATION MENU 4-3
3 THE ECHONAV MODE AND SELECTION MENUS 4-10
4 THE INDEX MARKERS 4-13
5 THE TIMERS 4-14
Operation
1 TO NAVIGATE THROUGH THE MENUS 5-1
2 USE THE FAVORITE LISTS 5-5
3 TO SELECT ANOTHER SATELLITE 5-6
4 TO USE THE INDEX MARKERS 5-6
5 TO USE THE PHOTO ALBUM 5-8
6 TO USE THE DVR STOP TIMER 5-9
Maintenance
1 USER LNB SETTING - SUB-MENU (ADVANCED ONLY) 6-1
2 SET LIMITS - SUB-MENU 6-1
3 SEARCH CHANNELS - ANALOG IF 6-2
4 ADD DATA (SAT/TP) - SUB-MENU 6-2
Troubleshooting
1 TO SOLVE AN INSTALLATION RELATED PROBLEM 7-1
Glossary
1 LIST OF USED ABBREVIATIONS 8-1
2 EXPLANATION OF USED TERMINOLOGY 8-2
Index
Appendix 1
1 LNB CONFIGURATION MATRIX A1-1
2 LNBF CONFIGURATION MATRIX A1-1
3 USER DEFINED LNB(F) MATRIX A1-2

Preface
Page IV EchoStar International Corporation
© 2002 EchoStar International Corporation
All rights reserved

Installation Section 3
EchoStar International Corporation Page 3 - 1
© 2002 EchoStar International Corporation
All rights reserved
3
INSTALLATION
1. TO SETUP YOUR RECEIVER FOR THE FIRST TIME
This procedure supersedes the procedure as given in the user manual from step 15 onwards.
The main differences are:
■Select Easy or Advanced installation,
Easy installation helps you to do the initial setup procedure where Advanced allows you to
program the receiver as required for non-standard installations.
■Add a new satellite,
In a satellite field you can select any known satellite in range from the database or add
your own defined satellite with the use of the S00 satellite.
■Add a new transponder,
In a transponder field you can select any known transponder from the database or add
your own defined transponder with the use of the TP00 transponder.
FOR ALL CONFIGURATIONS
FOR FIXED AND DISEQC 1..4 SWITCH CONFIGURATIONS - EASY
NOTE
From the next step onwards, the procedure is divided in different configurations. The
configurations are; Fixed, Motorized and SMATV.
■Fixed means set up a single dish or multiple dishes with DiSEqC1..4 switch;
■Motorized means set up a moveable dish (motor/actuator by positioner);
■SMATV means set up for television distribution (cable network in buildings).
1. Make the required selections.
2. Read the available help text for information.
3. Go to the Save settings field to confirm the time.
4. On the RCU, press the OK key to set the time.
Note that the local time is shown correctly.
5. Go to the Continue field.
6. On the RCU, press the OK key to advance
21. Make the required selections.
22. Set the required installation mode, recommended
setting is Easy (guided setup procedure).
23. Read the available help text for information.
Note that only the white fields are selectable, other
fields show reference information.
24. If you want to add your own defined satellite, go to
the SAT field and select S00 (Goes to the menu
where you can define your own satellite, for
detailed information, refer to section 6). If not
proceed with step 25.
25. Go to the Check signal field.
26. On the RCU, press the OK key to advance.

Section 3 Installation
Page 3 - 2 EchoNAV 2.2
© 2002 EchoStar International Corporation
All rights reserved
FOR MOVEABLE DISH INSTALLATIONS (DISEQC 1.2)
27. Wait for the Checking configuration to complete.
28. Read the available help text for information.
29. Make the required selections.
30. If the red dot in the TP field stays:
a. select another transponder;
b. go to the Check signal field;
c. on the RCU, press the OK key.
31. If you want to add your own defined transponder,
go to the TP field and select TP00 (Goes to the
menu where you can define your own transponder,
for detailed information, refer to section 6). If not
proceed with step 32.
32. Go to the Search channels field.
33. On the RCU, press the OK key to advance.
34. Wait for the search to complete:
a. the receiver display shows a moving dot;
b. the Search completed popup menu appears.
35. On the RCU, press the OK key to end the initial
setup procedure.
21. Make the required selections.
22. Set the required installation mode, recommended
setting is Easy (guided setup procedure).
23. Read the available help text for information.
Note that only the white fields are selectable, other
fields show reference information.
24. Go to the Program Satellites field.
25. On the RCU, press the OK key to advance.
26. Select the satellite which you want to receive.
27. Read the available help text for information.
Note that only the white fields are selectable, other
fields show reference information.
28. If you want to add your own defined satellite, go to
the SAT field and select S00 (Goes to the menu
where you can define your own satellite, for detailed
information, refer to section 6. If not proceed with
step 34.

Installation Section 3
EchoStar International Corporation Page 3 - 3
© 2002 EchoStar International Corporation
All rights reserved
3
FOR MOTORIZED CONFIGURATIONS - AUTOSAT
29. When in the Position field:
a. press and hold theor key and watch the
signal indicator for an indication;
b. in the signal indicator, make sure a network
name is shown;
c. press thekey to select another transponder for
signal verification;
d. press thekey to select the Position field;
e. use thekey to fine tune for the best signal
level and quality;
f. press the OK key, note that the saved position of
the satellite is shown.
30. If you want to add your own defined transponder for
the selected satellite, go to the TP field and select
TP00 (Goes to the menu where you can define your
own transponder, for detailed information, refer to
section 6). If not proceed with step 36.
31. Go to the Search channels field.
32. On the RCU, press the OK key to advance.
33. Wait for the search to complete:
a. the receiver display shows a moving dot;
b. the search completed popup menu appears.
34. On the RCU, press the OK key. to end the initial
setup procedure.
CAUTION
On the motorized dish, set the physical East and West limit switches first. Failing to
do so might cause damage to your motorized dish installation or other properties.
21. Make the required selections.
22. Set the required installation mode, recommended
setting is Easy (guided setup procedure).
23. Read the available help text for information.
Note that only the white fields are selectable, other
fields show reference information.
24. Go to the Autosat field.
25. On the RCU, press the OK key to advance.

Section 3 Installation
Page 3 - 4 EchoNAV 2.2
© 2002 EchoStar International Corporation
All rights reserved
26. On the RCU:
a. press thekey to set the EL (East limit);
b. at the Motor error, press thekey once;
c. press the OK key.
27. On the RCU, press the OK key.
28. Select the most East SAT which you can receive.
29. If you want to add your own defined East SAT,
select S00 (Goes to the menu where you can
define your own satellite, for detailed information,
refer to section 6). If not proceed with step 31.
30. If you want to add your own defined transponder
for the selected satellite, go to the TP field and
select TP00 (Goes to the menu where you can
define your own transponder, for detailed
information, refer to section 6). If not proceed with
step 31.
31. When in the Position field:
a. press and hold thekey and watch the signal
indicator for an indication;
b. in the signal indicator, make sure a network
name is shown;
c. press thekey to select another transponder for
signal verification;
d. press thekey to select the Position field;
e. use thekey to fine tune for the best signal
level and quality;
f. press the OK key, note that the saved position of
the satellite is shown.
32. Repeat the procedure for the middle and most
West SAT.
33. Set the WL (key), refer to step 26.
34. Go to the SAT list field.
35. On the RCU, press the OK key to advance.

Installation Section 3
EchoStar International Corporation Page 3 - 5
© 2002 EchoStar International Corporation
All rights reserved
3
FOR MOTORIZED CONFIGURATIONS - MANUAL SELECTION
36. Make the required selections.
37. Read the available help text for information.
38. Go to the Search channels field.
39. On the RCU, press the OK key to advance.
40. Wait for the search to complete:
a. the receiver display shows a moving dot;
b. the Search completed popup menu appears.
41. On the RCU, press the OK key to end the initial
setup procedure.
CAUTION
On the motorized dish, set the physical East and West limit switches first. Failing to
do so might cause damage to your motorized dish installation or other properties.
21. Make the required selections.
22. Set the required installation mode, recommended
setting is Easy (guided setup procedure).
23. Read the available help text for information.
Note that only the white fields are selectable, other
fields show reference information.
24. Go to the Method field and select Manual.
25. Go to the Set limits field.
26. On the RCU, press the OK key to advance.

Section 3 Installation
Page 3 - 6 EchoNAV 2.2
© 2002 EchoStar International Corporation
All rights reserved
27. On the RCU:
a. press thekey to set the EL (East limit);
b. at the Motor error, press thekey once;
c. press the OK key.
28. On the RCU:
a. press thekey to set the WL (west limit);
b. at the Motor error, press thekey once;
c. press the OK key.
29. Go to the Program satellites field.
30. On the RCU, press the OK key to advance.
31. Select the satellite which you want to receive.
32. Read the available help text for information.
Note that only the white fields are selectable, other
fields show reference information.
33. If you want to add your own defined satellite, go to
the SAT field and select S00 (Goes to the menu
where you can define your own satellite, for
detailed information, refer to section 6. If not
proceed with step 34.
34. When in the Position field:
a. press and hold theor key and watch the
signal indicator for an indication;
b. in the signal indicator, make sure a network
name is shown;
c. press thekey to select another transponder for
signal verification;
d. press thekey to select the Position field;
e. use thekey to fine tune for the best signal
level and quality;
f. press the OK key, note that the saved position of
the satellite is shown.
35. If you want to add your own defined transponder
for the selected satellite, go to the TP field and
select TP00 (Goes to the menu where you can
define your own transponder, for detailed
information, refer to section 6). If not proceed with
step 36.
36. Go to the Search channels field.
37. On the RCU, press the OK key to advance.
38. Wait for the search to complete:
a. the receiver display shows a moving dot;
b. the Search completed popup menu appears.
39. On the RCU, press the OK key to end the initial
setup procedure.

Installation Section 3
EchoStar International Corporation Page 3 - 7
© 2002 EchoStar International Corporation
All rights reserved
3
FOR SMATV CONFIGURATIONS
2. ADVANCED MODE (MULTIPLE LNB SUPPORT)
21. Make the required selections.
After the initial installation it is possible to add more
symbol rates. Refer to section Maintenance for
detailed instructions.
22. Read the available help text for information.
23. Go to the Search Channels field.
24. On the RCU, press the OK key to advance.
25. Wait for the search to complete:
a. the receiver display shows a moving dot;
b. the Search completed popup menu appears.
26. On the RCU, press the OK key to end the initial
setup procedure.
21. Make the required selections.
22. Use thekey to set the installation mode to
Advanced.
23. Note that the screen changes into the advanced
mode.
24. .If you want to return to the Easy mode, use
thekey to set the installation mode to Easy.
25. Read the available help text for information.
26. Go to the Set limits field.
27. On the RCU, press the OK key to advance.
28. Read the available help text for information.
29. Make the required selections.
30. Go to the Program satellites field.
31. On the RCU, press the OK key to advance.

Section 3 Installation
Page 3 - 8 EchoNAV 2.2
© 2002 EchoStar International Corporation
All rights reserved
32. Select the satellite which you want to receive.
33. Read the available help text for information.
Note that only the white fields are selectable, other
fields show reference information.
34. If you want to add your own defined satellite, go to
the SAT field and select S00 (Goes to the menu
where you can define your own satellite, for
detailed information, refer to section 6).
35. Go to the User LNB field and on the RCU press the
i-key.
36. Note that the software advances to the
User LNB setting menu.
37. Read the available help text for information.
38. Make the required selections.
39. Go to the Save settings field.
40. On the RCU, press the OK key to advance.
41. Note that the software returns to the Program
satellites menu.
42. Make the required selections.
43. If you want to add your own defined transponder
for the selected satellite, go to the TP field and
select TP00 (Goes to the menu where you can
define your own transponder, for detailed
information, refer to section 6).
44. Go to the Search channels field.
45. On the RCU, press the OK key to advance.
46. Wait for the search to complete:
a. the receiver display shows a moving dot;
b. the Search completed popup menu appears.
47. On the RCU, press the OK key to end the initial
setup procedure.

Familiarization Section 4
EchoStar International Corporation Page 4 - 1
© 2002 EchoStar International Corporation
All rights reserved
4
FAMILIARIZATION
1. ECHONAV 2.2
The software of the receiver contains the EchoNAV user interface with on-screen help, which
gives you easy control over the features of the receiver. The software contains also a large
database of pre-programmed satellites and transponders which are used for a quick
installation. For initial installation, the software guides you through the required setup menu to
allow for an easy and reliable installation setup of the receiver.
FEATURE HIGHLIGHTS
The highlights for this version are:
■New menu languages added;
Portuguese, Dutch.
■Revised help lines and related translations;
All menu texts are revised to give more support and information. All menu languages are
translated accordingly.
■Several small menu changes incorporated:
- LNB power option in system setup menu for SMATV deleted,
- Time zone option in Local time menu deleted,
- Software identification in About EchoStar menu is changed to show EchoNAV version.
■Revised subtitle behavior;
Greek and Russian subtitle support is added.
■Multi-lingual language support for EPG added;
If available form the service provider, EPG language is shown in the language which is set
for the menu language (user preferences - Languages - Menu).
■Revised conditional access to support smartcards type PC2.4;
The embedded Viaccess smartcard reader is revised to support the latest generation of
PC2.4 smartcards as used by several service providers who use Viaccess encryption.
■Revised channel numbering for Current SAT list;
The Current SAT list is revised to have it’s own channel numbering. Therefore the channel
numbering (only for Current SAT) starts at 1 for each satellite. Note that also the satellite
name is shown permanently.
■New installation menus added for multiple LNB support;
The installation menu is revised to support Easy and Advanced installation. In the
advanced installation you can define user defined LNBs where the Easy installation allows
for the installation of pre-defined LNBs.
■Revised Add SAT, TP and PID menus;
The Add SAT, Add TP, and Add PID are combined in one menu Add data.
■New option to add satellite or transponder during initial installation setup added;
Add Data menu is accessible from the initial setup and after installation from the channel
list through the ‘white edit’ menu.
■OTA service added on ASTRA1, 19.2 East.
■DVR timer modified to allow for recording a relative time block;
The DVR timer is directly accessible after a recording is started. You can set the stop time
either in absolute time (13:00 hr) or relative time (+ 00:15 min).
■Updated satellite/transponder database,
You have to perform a factory reset to activate the database, failing to do so keeps the
previous database active.

Section 4 Familiarization
Page 4 - 2 EchoNAV 2.2
© 2002 EchoStar International Corporation
All rights reserved
1.1. THE REMOTE CONTROL UNIT (RCU)
The EchoStar Quattro is a programmable RCU that also can control your TV, VCR, DVD
and/or Audio set. The EchoStar Quattro requires two AA/R6 alkaline batteries to operate.
■ON/STANDBY
To switch to standby or on.
■VCR
To control the VCR.
■TV
To control the TV.
■EPG
To view the EPG.
■MENU
To go to the installation menu;
To go to the special functions.
■VOL+
To increase the volume.
■VOL-
To decrease the volume.
■ARROW CLUSTER
To scroll left, up, right or down.
■EXIT
To leave a menu or feature.
■PAGE+
To go one page up.
■PAGE -
To go one page down.
■ALT AUDIO
To choose a language.
■ALT SUBTITLE
To choose a subtitle.
■STOP
To stop the recording or play
back of an event;
To return to actual time in the
EPG window
■REWIND
To go to the beginning of an
recorded event fastly.
■RECORD (press twice)
To record a live program.
To show the DVR stop timer.
■PREVIOUS
To go to the previous event.
■GREEN
To select a (favorites) list.
■RED
To go to another mode.
■NUMBER KEYS
To enter numerical settings;
To type in a channel number.
■TV/RAD
To switch to TV or Radio
mode.
■MUTE
To blank out the volume.
■AUX
To control the Audio Set or
DVD.
■SAT
To control the receiver.
■i
To view the InfoBanner;
To view detailed EPG
information.
■Satellite Dish
To select another satellite.
■CH+
To go one channel up.
■CH-
To go one channel down.
■OK
To go to the (favorites) lists;
To make a menu selection;
To pull down a selection menu.
■RECALL
To go to the previous channel;
■?
Not used for Sat-mode.
■V (white)
To edit a list
■PLAY
To play back a recorded event.
■FAST FORWARD
To go to the end of an
recorded event fastly.
■PAUSE
To pause the playback of an
event;
To pause a live program.
■NEXT
To go to the next event.
■YELLOW
To group a list;
To select an EPG timer.
■BLUE
To sort a list;
To zoom in/out the time slot of
the EPG view window.
■FAV
To go to the favorite list of the
actual mode.

Familiarization Section 4
EchoStar International Corporation Page 4 - 3
© 2002 EchoStar International Corporation
All rights reserved
4
2. THE ECHONAV INSTALLATION MENU
A highlighted button shows you which (main/sub) menu is selected. The MENU key lets you
change between the main and sub-menu where thekeys let you make a selection in the
selected (main/sub) menu. The OK key brings you into the related page, where you can make
a choice from the available options.
■The button, that gives you access to the User Preferences menu;
■The button, that gives you access to the installation setup menu;
■The button, that gives you access to the Conditional Access menu.
2.1. THE USER PREFERENCES MENU
■The button, that gives you access to the User Profile page.
■The button, that gives you access to the Languages page.
■The button, that gives you access to the Parental Lock page.
■The button, that gives you access to the Local Time page.
■The button, that gives you access to the TV System page.
2.1.1. USER PROFILE SUB-MENU
This sub-menu allows you to customize the user profile settings, you can customize:
NOTE
Once in a page, at any time:
■you can use the MENU key to reverse from a menu page to the sub-menu bar;
■you can easily leave with the EXIT key.
This main menu has different sub-menus that give
access to the pages where you can customize the
factory settings.
The user preferences menu always comes in view with
the User Profile sub-menu. In the menu bar the
sub menus are shown at the right side. The available
sub menus are shown as icons which become a
highlighted button after selection.
The sub-menus are accessible with:
■Aspect ratio
To set the screen size of the TV.
■InfoBanner time-out
To select the view time for the InfoBanner.
■Dolby Digital
To tell the receiver that it is connected to a Dolby
Digital amplifier or not.
■RGB-Sync
To switch the RGB-sync signal, which is required by
monitors only, to On (monitor) or Off (TV).
■Backgrounds
To select the standard or a personal background
color.

Section 4 Familiarization
Page 4 - 4 EchoNAV 2.2
© 2002 EchoStar International Corporation
All rights reserved
2.1.2. LOCAL TIME SUB-MENU
This sub-menu allows you to customize the local time settings. For the correct operation of
the EPG and the timers, it is necessary to set the local time correctly. You can customize:
2.2. THE INSTALLATION SETUP MENU
■The button, that gives you access to the System Setup page (for Fixed dish, SMATV);
■The button, that gives you access to the System Setup page (for motorized dish);
■The button, that gives you access to the Program Satellites page (for motorized dish);
■The button, that gives you access to the User LNB Setting page (For Advanced only);
■The button, that gives you access to the Set East/West Limit page;
■The button, that gives you access to the About EchoStar information page;
■The button, that gives you access to the System Upgrade page;
■The button, that gives you access to the Factory Reset page.
■Year
To set the actual year.
■Month
To set the actual month.
■Date
To set the actual date.
■Day
To set the actual day.
■Hour
To set the actual time in hours.
■Minute
To set the actual time in minutes.
■Save settings
To confirm the settings you made.
This main menu has different sub-menus that give
access to the pages where you can customize the
settings to match your personal requirements.
Note that the sub-menus are dynamic which means that
they change with the selections you make.
The installation setup menu always comes in view with
the system setup sub-menu. In the menu bar the
sub menus are shown at the right side. The available
sub menus are shown as icons which become a
highlighted button after selection. The sub-menus are
accessible with:

Familiarization Section 4
EchoStar International Corporation Page 4 - 5
© 2002 EchoStar International Corporation
All rights reserved
4
2.2.1. SYSTEM SETUP SUB-MENU - EASY
DVR-7000 HDD ONLY
This sub-menu allows you to customize the system setup to match your installation. Note that
the menu page is dynamic which means that it changes with the selections you make. You
can customize:
■System
To select the dish type you use.
■Installation (fixed, motorized only)
To select the guided setup procedure for Easy
installations or Advanced installations with multiple
user defined LNBs.
■LNBs
To set the amount of LNBs you have installed.
■Polarity
To set the device that controls the signal polarity.
■Switch
To set the switch type which you use to control the
dish installation (if used).
■LNB1
To set the LNB type(s) you use.
■SAT (for fixed only)
To select the satellite you want to scan for the LNB.
Satellite S00 brings you to the add data menu.
■Method (for motorized only)
To set the channel search method;
AutoSat (automatically calculate the satellite
positions from reference positions)
Manual (enter the satellites by manual search).
■AutoSat (for motorized, AutoSat only)
To confirm the selections you made and advance to
the AutoSat setup page (AutoSat only)
■Set limits (for motorized, manual only)
To confirm the selections you made and advance to
the Set limits page.
■Check signal (for fixed only)
To confirm the selections you made and advance to
the Check signal page.
■Symbol rate1-4 (for SMATV only)
To set the symbol rate you want to scan.
■Search channels (for SMATV only)
To confirm the selections you made and advance to
the Search channels page.

Section 4 Familiarization
Page 4 - 6 EchoNAV 2.2
© 2002 EchoStar International Corporation
All rights reserved
DVR-5000 HDD ONLY
This sub-menu allows you to customize the system setup to match your installation. Note that
the menu page is dynamic which means that it changes with the selections you make. You
can customize:
■System
To select the dish type you use.
■Installation (fixed, DiSEqC 1.2 only)
To select the guided setup procedure for Easy
installations or Advanced installations with multiple
user defined LNBs.
■LNBs
To set the amount of LNBs you have installed.
■Polarity
To set the device that controls the signal polarity.
■Switch
To set the switch type which you use to control the
dish installation (if used).
■LNB1
To set the LNB type(s) you use.
■Program Satellites (DiSEqC1.2 only)
To confirm the selections and go to next menu.
■SAT (for fixed only)
To select the satellite you want to scan for the LNB.
Satellite S00 brings you to the add data menu.
■Check signal (for fixed only)
To confirm the selections you made and advance to
the Check signal page.
■Symbol rate1-4 (for SMATV only)
To set the symbol rate you want to scan.
■Search channels (for SMATV only)
To confirm the selections you made and advance to
the Search channels page.