Eclipse CD5405 User manual

OWNER'SMANUAL
We appreciate your purchase of this receiver.
Please read through this manual for correct operation.
We suggest that after reading it you keep this manual
in a safe place for future reference.
CD5405
ESN E5 High-Power CD Receiver
www.eclipse-web.com
FUJITSU TEN LIMITED
Contact:FUJITSU TEN CORP. OF AMERICA
19600 So. Vermont Avenue, Torrance, CA 90502
Call:800-233-ECLIPSE
OWNER'S MANUAL
CD5405 ESN E5 High-Power CD Receiver
090001-14660700 0411MT (F.O)
"ECLIPSE" is a registered trademark of
FUJITSU TEN LIMITED in 48 countries
including the U.S. and Japan.
CUSTOMER NOTICE
Please retain this booklet and write in the serial number
of your CD5405 for identification.
The serial number is labeled or stamped on the chassis.
Serial No.
CD5405出力04.11.252:02PMページ1

2
For your safety in using the
CD5405
Warnings and caution signs, illustrated below, are posted
throughout this manual as well as on the CD5405. They show safe
and correct ways to handle the product so as to prevent personal
injury to you, others and to avoid property damage.
Before reading through the manual, take time to read through and
learn the important information listed in this section.
This sign indicates a situation in which
incorrect handling or disregard of this sign
might result in death or serious personal injury.
This sign indicates a situation in which
incorrect handling or disregard of this sign
might result in personal injury or may result
solely in damage to property.
• Do not modify this system for use other than that specified
herein. Also, do not deviate from the installation procedures
described herein; Eclipse will not be held liable for damages
including, but not limited to serious injury, death or property
damage resulting from installations that enable unintended
operation.
• This equipment requires 12V DC and should only be installed in
a vehicle with a 12V negative ground electrical system. Any
other installation may cause a fire or other severe damage to
the equipment and the vehicle.
• Never install this equipment where it will interfere with safe
operation of the vehicle. Never block the driver's view. Do not
install equipment where it may interfere with operation of the
brakes, the steering or any safety equipment, including seat
belts and air bags.
• When installing equipment do not remove or alter existing
vehicle fasteners, including nuts, bolts, screws, clips, and
fittings. Never detach, move or alter existing vehicle wiring,
including electrical grounds and straps. Alteration of existing
vehicle components may make vehicle unsafe to operate.
Warning
Caution
Warning

3
• Before installation, remove the negative (-) battery terminal to
prevent shocks, electrical arcing, fires, and damage to vehicle
wiring and the equipment you are installing.
• Secure wiring with tape or plastic ties so that wires do not
interfere with vehicle operation, including brake pedal, gear
shifter and steering. Position wires so that they will not be
rubbed, abraded, or damaged by moving vehicle components,
including power seats.
• To avoid equipment and vehicle damage, including fire, never
supply power to installed equipment in a way which will
overload the capacity of an existing vehicle circuit. Never
leave a power supply wire or connection uninsulated. Always
install supplied fuses, circuit breakers, and relays.
• Air bags are vital safety equipment. Never install equipment in
a way which will alter air bag wiring or interfere with air bag
deployment. Air bags must function properly in the event of an
accident.
• For your protection, never use a power drill without safety
glasses or goggles. Debris or broken drill bits may cause
severe eye injuries, including blindness.
• Use electrical tape to insulate the ends of all wires, even if not
used. Proper insulation prevents arcs, shocks and fires.
• Some equipment uses batteries. Never install equipment
where young children can get access to batteries. If a battery
is swallowed, seek medical attention immediately.
• When vehicle is moving, never take your eyes off the road to
make adjustments to the equipment. You must pay attention to
the road to avoid accidents, do not let the operation or
adjustment of the equipment distract you from proper vehicle
operation.
• The driver should not look at the screen while driving.
Accidents may result if you are not paying attention to the
forward direction.
• Do not put foreign objects in the loading slot of disc. Fires or
shocks may result.
• Do not disassemble or alter this equipment. Accidents, fires or
shocks may result.
Warning

4
•Do not let water or foreign objects enter the internal parts of this
equipment. Smoke, fires or shocks may result.
•Pay attention to where the remote control is left. Traffic
accidents or problems with driving may result if the remote
control makes its way under the brake pedal etc. when the
vehicle is stopped or when it goes around a corner.
•Do not use when it is broken (the screen is not lit or no sound
comes out). Accidents, fires or shocks may result.
•Always replace fuses with fuses of identical capacity and
characteristics. Never use a heavier fuse than the original.
Using the wrong type of fuse may cause a fire or severe
damage.
•If foreign objects or water enters the equipment, smoke comes
out, or there is a strange odor, stop using it immediately, and
contact your dealer. Accidents, fires, or shocks may result if
you continue to use it in these conditions.
•The driver should not change the CD while driving. As
accidents may result if you are not paying attention to the
forward direction, first stop the car at a safe location and then
proceed.
•Plastic bags and wrappings may cause suffocation and death.
Keep away from babies and children. Never put bag over your
head or mouth.
• Wiring and installing this equipment requires expertise and
experience. Professional installation is recommended. Consult
with your dealer or a professional installer. Incorrect wiring may
damage the equipment or interfere with safe vehicle operation.
• Use only the accessory parts as specified. Using other parts may cause
damage to the equipment or cause parts to fall or fly off the equipment.
•Do not install the unit in places where it may get dew
condensation on (around the air conditioning hose, etc.), come
in contact with water, or in condition of high moisture, dust or
oily smoke. If water, moisture, dust or oily smoke enters this
unit, smoke, fires or malfunctions may result.
Caution
Warning

5
•Avoid installing in places where it cannot be fastened securely
or where there are strong vibrations. Also, if you installed the
unit with double-sided tape, first wipe away dirt and wax from
the installation area. Otherwise, the unit may come loose due
to vibration while driving, causing problems for driving and
resulting in traffic accidents or injuries.
•
Do not install in places with direct sunlight or where it will be hit
directly by hot air from the heater. This may increase the temperature
of the interior of this equipment, resulting in fires and malfunctions.
• Do not block the fan, heat sink or vents for this unit. When fan, heat
sink or vent is blocked, the interior overheats, and fires may result.
•Connect as specified in the installation manual. If not
connected normally, fires or accidents may result.
•When installing in vehicles equipped with air bags, check the
manufacturer's cautions regarding operation before operating.
Airbags may not operate properly.
•Carry out the wiring such that cords are not pinched by
movable parts such as seat rails, and screw parts of the vehicle
body. Accidents, fires and shocks may result from
disconnection and electrical shorts.
•Carry out the wiring such that the cord does not make contact
with metal parts. The cord is may be damaged by contact with
metal parts, resulting in fire and shocks.
•Avoid hot surfaces when wiring equipment. High temperatures
may damage wiring, causing shorts, arcing and fires.
•When changing the installation location for this equipment,
please consult the dealer where you bought it for safety
reasons. Expertise is necessary for removal and installation.
•Keep volume to a reasonable level so that you can hear sounds
from outside the vehicle, including warning sounds, voices, and
sirens. Failure to do so may cause an accident.
•Do not put your hands or fingers into the loading slot of disc.
Injuries may result.
•Do not touch the heat dissipating part of the amp. Burns may
result from the heat of this part.
•Do not recharge dry batteries. Dry batteries may rupture,
resulting in injuries.
Caution

6
•Do not use batteries other than those specified. Also, do not
mix old and new batteries. Injuries or pollution to the
surroundings may result from battery ruptures and leakage.
•When inserting batteries into the equipment, be careful of the
polarity (positive/negative), and insert them as indicated. If the
battery polarities are incorrect, injuries and pollution to the
surroundings may result from battery ruptures and leakage.
•Replace used batteries as soon as possible; they may leak and
damage equipment. Battery leakage can burn your skin or
your eyes. Wash hands after handling.
•
If alkaline solution from alkaline dry batteries makes contact with your
skin or clothes, flush with clean water. If any of the solution gets in your
eyes, also flush clean with water and then seek medical attention.
• When disposing of lithium dry batteries, affix insulating tape to
the positive and negative terminals, and after they are insulated,
dispose of them according to the "Local municipal directives".
Shorts, fires and ruptures may result from disposal together with
other electrically conductive objects such as metal parts, etc.
• Do not short, disassemble or heat the batteries, or place them in fire or
water. Fire and injuries may result from battery rupture and leakage.
•Store the remote control in a place away from direct sunlight,
high temperatures, and high moisture levels. The case may
change shape, and the batteries may rupture and leak.
•Do not use this equipment except for in-vehicle use. Shocks or
injuries may result.
•Be careful of the position of the volume when turning the power
source ON. Hearing damage may result if very loud noise is
emitted when the power is turned ON.
•Do not operate under abnormal conditions such as when the
sound is broken or distorted. Fires may result.
•This equipment uses invisible laser light. Do not disassemble
or alter this equipment. If trouble occurs, contact the dealer
where you bought the equipment. Altering this equipment may
cause exposure to laser emissions (worsening eyesight), or
result in accidents, fires or shocks.
•If the equipment is dropped or the cabinet is broken, turn off
the power to the main unit and contact your dealer. If used in
this condition, fires or shocks may result.
Caution

7
Table of Contents
Operating precautions ............................................. 10
Notes on operation ..................................................................... 10
About compact discs .................................................................. 11
About cleaning a CD .................................................................. 13
Names of controls and parts .................................. 14
ESN security operating procedure ......................... 15
About ESN .................................................................................. 15
How to operate the ESN (Key CD) security ................................ 16
How to program the Key CD ................................................ 16
How to cancel the Key CD ................................................... 17
How to change the Key CD .................................................. 18
How to resume normal operation (ESN security lock out) ... 18
What happens if an incorrect CD is inserted? ...................... 19
How to turn the security indicator on/off ..................................... 20
How to read the Electronic Serial Number ................................. 20
Basic operation ........................................................ 21
Turning the power on and off ..................................................... 21
Listening to a CD ........................................................................ 22
Listening to the tuner .................................................................. 23
Adjusting audio volume .............................................................. 24
Switching audio control modes ................................................... 25
VOL (VOLUME) Mode ......................................................... 25
BASS Mode ......................................................................... 25
MID (MIDDLE) Mode ........................................................... 26
TREB (TREBLE) Mode ........................................................ 26
BAL (BALANCE) Mode ........................................................ 26
FAD (FADER) Mode ............................................................ 26
NON-F (NON-FADER) Mode ............................................... 26
NF-P (NON-PHASE) Mode .................................................. 27
LOUD Mode ......................................................................... 27
Storing user presets for the equalizer ........................................ 27
Changing the equalizer mode .................................................... 28
Making changes with Function Mode ......................................... 29
Disabling the guide tone feature (for button operation) ........ 29
Setting the time .................................................................... 30
Changing the LINE OUT mode ............................................ 31

8
How to operate the CD player ................................. 32
Listening to CDs ......................................................................... 32
Advancing to the next track or returning to the beginning of the
track being played ...................................................................... 33
Fast Forward/Rewind ................................................................. 33
Playing the beginning of tracks (SCAN) ..................................... 33
Repeating the same track (REPEAT) ......................................... 34
Playing tracks in random order (RANDOM) ............................... 34
Ejecting the disc ......................................................................... 35
Switching the display .................................................................. 35
How to operate the tuner ........................................ 36
Tuning to a station ...................................................................... 36
Entering stations into memory automatically
(The automatic preset mode: ASM) .......................................... 37
Manually setting stations into memory ....................................... 38
Preset station scan ..................................................................... 39
Switching the display .................................................................. 39
Changing the reception sensitivity for automatic scanning ........ 40
Changing the radio band location ............................................... 40
FM reception characteristics ...................................................... 41
FM reception differs from AM ............................................... 41
Fading out ............................................................................ 41
Reception area of FM broadcasts ........................................ 42
Multipath .............................................................................. 42
How to use an optional remote control ................. 43
Precautions in use of the remote control .................................... 43
Cleaning the remote control ....................................................... 43
Turning the power on/off ............................................................ 44
Adjusting the audio volume ........................................................ 44
Muting the volume ................................................................ 44
Switching playback modes ......................................................... 45
How to play the tuner ................................................................. 45
Selecting the FM/AM band ................................................... 45
Selecting a station (manually or automatically) .................... 46
Selecting preset stations ...................................................... 46
How to play CDs ......................................................................... 46
Switching disc mode ............................................................ 46
Advancing to the next track or returning to the beginning
of the track being played ...................................................... 47
Replacing the battery ................................................................. 48

9
If you have a question: ............................................ 49
Displayed information (for troubleshooting) ................................ 50
Specifications .......................................................... 53
Before installation ................................................... 54
Components ............................................................................... 54
Installation angle ........................................................................ 54
Mounting instruction ............................................... 55
Mounting the main unit ............................................................... 55
Names of lead wires and destinations ........................................ 58
System ....................................................................................... 59
How to contact customer service ............................62

10
Operating precautions
<Your CD5405 will perform well over a long period of time through correct
handling and care.>
•For your safety, play only at volume levels that allow outside sounds to be
heard.
•We recommend using with this player a disc with
the logo shown to the left.
•You can play music CDs(CD-R/CD-RW) on this
player. Be sure to use discs that have been
properly processed.
Depending on the editing equipment used, some
discs may not play properly.
•CD-R and CD-RW discs recorded in the MP3 file
format are not playable.
•Do not insert anything other than a CD into the
disc slot.
Do not insert any foreign objects, such as coins or
credit cards, into the disc slot. Be especially
watchful of children’s mischief in this regard.
•Avoid severe mechanical shock.
When the player is subjected to severe vibration
while traveling over a rough surface, playback
may be intermittent. When a situation like this
occurs, resume playback after returning to a
smoother road.
•About dew condensation.
In cold or rainy weather, just as the interior glass
surface gets fogged, dew (water condensation)
may also settle on the deck. When this occurs,
disc playback may become intermittent or
impossible. Dehumidify the air in the vehicle for a
while before resuming playback.
•Cleaning the disc slot.
The disc slot tends to get dusty. Clean it
occasionally to prevent accumulated dust from
scratching the discs.
Notes on operation
Operating precautions

11
Operating precautions
•The signal recorded on a compact disc is read by a laser beam, so
nothing touches the disc surface. A scratch on the recorded surface or a
badly warped disc may cause deteriorated sound quality or intermittent
playback. Observe the following precautions to ensure high quality sound
performance:
•Do not leave an ejected disc in the disc slot
for very long; the disc may warp. Discs
should be stored in their cases and kept
away from high temperature and humidity.
•Do not stick a piece of paper or tape on, nor
write on or scratch either side of a disc.
•Discs spin at a high speed inside the deck.
Keep cracked or warped discs out of the
player to avoid damaging it.
•Avoid touching the recorded surface when
handling a disc; handle discs by their edges.
About compact discs

12
Operating precautions
About CD accessories
•Do not use accessories
(stabilizers, protective seals, laser
lens cleaners, etc.) sold for
“improving sound performance”
or “protecting CDs.”The changes
in CD thickness or outside
dimensions made by these
accessories may cause problems
in the player.
About brand new CDs
•You may notice that some brand
new discs are rough around the
center hole or outside edge.
Remove the rough edges with
the side of a ballpoint pen, etc.
Rough edges may prevent
proper loading in the deck.
Flakes from the rough edges
may also stick to the recorded
surface and interfere with
playback.
Rough Edges
Ballpoint
pen
Flakes
Recorded surface
Rough
Edges
•Please be sure NOT to attach any
ring-shape protector (or other
accessory) to your discs. Those
protectors are commercially
available and said to protect disc
and to improve sound quality
(and antivibration effect), but they
can do more harm than good in
regular uses. The most common
problems are disc insertion, disc
ejections, and won't play
problems due to the protector
ring that came off in the disc
mechanism.

13
Operating precautions
About borrowed CDs
•Do not use a CD with glue or
remnants of adhesive tape or
labels. They may cause the CD
to get stuck inside or damage
the deck.
How to remove CDs
•When removing the ejected disc,
pull it straight out along the slot.
Pressing downward in the
process may scratch the
recorded surface of the disc.
OKAY
NO GOOD
About irregularly-shaped CDs
•Specially-shaped CDs, like
heart-shaped or octagonal CDs,
cannot be played. Do not
attempt to play them, even with
an adapter, since they may
damage the player.
•Use a commercially available compact disc
cleaner to clean a CD, wiping lightly from the
center to the edge.
•Do not use benzine, thinner, LP record spray
or other cleaners on CDs. They may damage
a CD’s finish.
XXXX
XXXX
XXXX
About cleaning a CD

14
Names of controls and parts
Names of controls and parts
Ejects compact disc.
Switches between disc modes.
Switches to radio mode and switches radio bands.
Inserts compact discs.
Switches screen display and turns function mode ON/OFF.
Sets the equalizer settings.
Selects radio stations and CD tracks.
Automatically finds radio reception or to fast forward/rewind.
Returns to previous screen.
Resets deck functions to default settings.
Selects radio preset channels and performs disc mode
functions.
Adjusts volume and performs other functions.
Turns deck power ON/OFF.
Mutes or cancels muting.
[CD (EJECT) ] button
[DISC] button
[FM AM] button
Disc slot
[DISP FUNC] button
[SOUND] button
[SEL] button
[ / ] button
[RTN] button
[RESET] button
Buttons [1] to [6]
[AUDIO CONTROL] button
[PWR] button
[MUTE] button
① ② ④ ⑥ ⑦③
⑬⑫ ⑪⑩⑧
⑨
⑭
⑤⑧

15
ESN security operating procedure
ESN security operating procedure
About ESN
This deck incorporates ESN (ECLIPSE Security Network). The ESN is
a security system which disables all deck functions when the power
is restored if the deck is stolen from the vehicle. Once the ESN is
activated, removing power to the deck or vehicle will activate the
security feature.
Setting or canceling of the security feature can be done with a "Key
CD". It is necessary to register a music CD as the "Key CD"in
advance.

16
ESN security operating procedure
ATTENTION
•If there is a problem with the inserted CD, an [ERR] message
will appear for two seconds and the CD will be ejected. Reinsert
the ejected CD.
•If a CD causes the [ERR] message to appear twice in a row, a
[CHANGE] message will appear for two seconds. Try another
CD.
•Copy protected CD cannot be programmed for Key CD
security.
•The Security indicator will flash whenever the vehicle’s ignition
is switched off.
ATTENTION
•If a CD has already been inserted, a [SEC] message appears,
and then the CD is ejected.
•If a security is activated, programming the Key CD is not
available.
How to operate the ESN (Key CD) security
How to program the Key CD
[DISP FUNC] button
Button [6]
Check that the the unit is in standby.
1
Press and hold button [6], then the [DISP FUNC]
button, and hold both for more than one second.
2
A [SEC] message appears, then in two seconds it will
change to [DISC].
The CD5405 is now ready to accept your Key CD in the
CD slot.
Insert the CD into the slot.
3
A [SEC] message appears, then the Key CD is ejected.

17
ESN security operating procedure
ATTENTION
•This process cancels the protection for the ESN deck.
•If power to the ESN deck is disconnected, then reconnected, a
Key CD will not need to be inserted in order to return the unit to
normal operation.
•Inserting a CD other than the Key CD will not cancel the
protection. Instead, the display [ERR] for two seconds, then the
normal CD playback mode will activate.
ATTENTION
If a CD has already been inserted, a [SEC] message appears,
and then the CD is ejected.
How to cancel the Key CD
[DISP FUNC] button
Button [6]
Check that the unit is in standby.
1
Press and hold button [6], then the [DISP FUNC]
button, and hold both for more than one second.
2
A [SEC] message appears, then in two seconds it will
change to [DISC].
The CD5405 is now ready to accept your Key CD in the
CD slot.
Insert your Key CD into the slot.
3
A [CANCEL] message appears, then the Key CD is
ejected.
The Key CD is canceled.

18
ESN security operating procedure
ATTENTION
•If an incorrect CD is inserted, an [ERR_] ("ERR" and error
number) message will appear for two seconds, after which the
CD will be ejected.
•If [ERR5] (the 5th time an error has occurred) appears, [HELP]
will appear, after which the CD will be ejected. When [HELP]
appears, carry out the operations for an ESN security lock out
by following the procedure in "What happens if an incorrect CD
is inserted?" (See next page).
•You must use the same CD used for Key CD programming; a
duplicate CD may not work properly.
How to change the Key CD
If power is disconnected while ESN security is active (a Key
CD was programmed), operation is disabled until power is
restored and the unit unlocked. Follow this procedure to
resume normal operation.
How to resume normal operation (ESN security lock out)
First, cancel the existing Key CD.
1
When the power is turned on after disconnecting
the battery power, a [SEC] message will appear for
two seconds. Thereafter, the message changes to
[DISC] and the CD5405 is ready to accept your Key
CD into the slot.
1
Next, program a new Key CD.
2
Refer to “How to program the Key CD.”
Insert your Key CD into the slot.
2
If the correct CD is inserted, an [OK] message will
appear for two seconds and the CD will begin playing.
Refer to “How to cancel the Key CD.”

19
ESN security operating procedure
ATTENTION
•If an incorrect CD is inserted, an [ERR_] ("ERR" and error
number) message will appear for two seconds, after which the
CD will be ejected.
•This process cancels the protection for the ESN deck.
What happens if an incorrect CD is inserted?
Note 
If after five tries the correct Key CD is not inserted, the display
reads [CALL800]; the unit must be returned to Eclipse to be
reset. In this case, please contact your Eclipse dealer for
assistance. For country-specific customer service information,
refer to "How to contact customer service" on page 62.
Your key CD can be easily forgotten. Write the
album name in a reminder note (See Page 67).
[DISP FUNC] button
Button [6]
After the 5th incorrect attempt, the display reads
[HELP] for five seconds.
1
[HELP] will appear for five seconds, after which the serial
number will appear.
Press button [6], then the [DISP FUNC] button, and
hold them for five seconds.
2
After the [SEC] message will appear for two seconds,
rolling code will appear.
Press the [DISP FUNC] button.
3After the [SEC] message will appear for two seconds,
rolling code will appear.
Insert your Key CD into the slot.
4If the correct CD is inserted, an [OK] message will
appear for two seconds and CD will be ejected.

20
ESN security operating procedure
How to turn the security indicator on/off
With the unit in standby, press button [2], then the [DISP
FUNC] button and hold both for more than one second.
1
[IND. FLASH] or [IND. -----] appears on the display.
2
[IND. FLASH] means the security indicator will flash when the
vehicle’s ignition is off, and [IND. -----] means it will not. Repeat
the above steps to reactivate the flash mode.
Once ESN security is activated, the indicator flashes whenever the
vehicle’s ignition is turned off, warning potential thieves that the unit
is protected. However, if you do not want this visible deterrent, it may
be turned off.
How to read the Electronic Serial Number
Check that the unit is in standby.
1
Press button [4], then the [DISP FUNC] button, and hold
both for more than one second.
2
[ESN] appears on the display, followed by an eight-digit
number; this number is your electronic serial number (ESN).
You may use this number to identify your Eclipse CD5405 in
the event it is recovered after being stolen.
Button [2] [DISP FUNC] button
Button [4]