Eco-Smart LR411U-2.4X7IR-1M-1024 User manual

Item #1009 513 064
Model #LR411U-2.4X7IR-
1M-1024
40 in WHITE BATTERY POWERED
STRIP LIGHT WITH MOTION SENSOR

Table of Contents ...................................
.................................
2
Safety Information 2
Warranty ................................................3
Pre-Installation ......................................4
Installation ........................................5
THIS IS AN ELECTRIC LIGHT - NOT A TOY! TO AVOID RISK OF
FIRE, BURNS, PERSONAL INJURY, ELECTRIC SHOCK AND ACCIDENTALLY
INGESTION OF BATTERIES IT SHOULD NOT BE PLAYED WITH OR PLACED
WHERE SMALL CHILDREN CAN REACH IT
.............................
Operation ..........................................8
Care and Cleaning
Battery Safety
11
....................................11
2
This strip light is intended for indoor use only
This strip light is not intended for commercial use
Do not expose the strip light to excessive heat or moisture
Do not look directly at the strip light when it is illuminated.

Warranty
The manufacturer warrants this xture to be free from defects in materials and
workmanship for a period of two (2) years from date of purchase. This warranty applies
only to the original consumer purchaser and only to products used in normal use and
service. If this product is found to be defective, the manufacturer’s only obligation, and
your exclusive remedy, is the repair or replacement of the product at the manufacturer’s
discretion, provided that the product has not been damaged through misuse, abuse,
accident, modications, alteration, neglect, or mishandling. This warranty shall not
apply to any product that is found to have been improperly installed, set-up, or used in
any way not in accordance with the instructions supplied with the product. This
warranty shall not apply to a failure of the product as a result of an accident, misuse,
abuse, negligence, alteration, faulty installation, or any other failure not relating to
faulty material or workmanship. This warranty shall not apply to the nish on any
portion of the product, such as surface and/or weathering, as this is considered normal
wear and tear.
Contact the Customer Service Team at 1-800-910-7164 or visit
www.HomeDepot.com/EcoSmart.
3

Contact the Customer Service Team at 1-800-910-7164 or visit
www.HomeDepot.com/EcoSmart.
Part Description
Strip light
Controller
B
A
C
Quantity
1
1
D
AAA batteries 4
Remote control
1
E
Mounting clips
2
F
Screws
2
A
D
E
B
C
F
4

(optional) Shorten the strip light (A) to the desired length by
cutting along the black lines.
Prepare the strip light
5

Ensure that the mounting location is even, clean, and dry.
Remove the protective film from the back of the strip light (A).
Press the strip light (A) to the mounting surface and hold in
place for a few seconds.
Install the strip light
6

E
F
Remove the protective film from the back of the controller (B).
Press the controller (B) to the mounting surface and hold in
place for a few seconds.
Use the mounting clips(E) and screws(F) to further secure the
strip light.
Install the controller
3
Note: Use the screws to secure the installation and avoid strip light
falling down when adhesive lose viscosity
7

1
5
6
9
7
2
3
4
8
CAUTION: The remote control included utilizes a 3V CR2025battery; Donot dispose of batteries
in fire as they may explode or leak. Please dispose of used batteries immediately and safely. Only
replace with the samebattery type. Examine devices and make sure the battery compartment is
correctly secured, e.g. that the screw or other mechanical fastener is tightened. Do not use if
compartment is not secure.
WARNING: KEEP BATTERIES OUT OF THE REACH OF CHILDREN! BATTERIES ARE NOT A TOY! If swallowed,
they can cause severe injury or death within 2 hours. In case of swallowing, call emergency
services immediately. Tell others of the risks associated with button batteries to keep kids safe.
Operating the remote
8
Aim the remote directly at the controller.
Remove the plastic tab from the back of the handheld remote (D).
Ensure the battery contacts are clean prior to battery installation.
Remove batteries from equipment when not in use for an extended
period to time. Note: When the remote and
the controller set the motion mode
together, the nal effect depends
on the last command.

1
2
3
4
5
6
7
8
9
Button Description
ON: Press to turn on the light
OFF: Press to turn off the light
Adjustable brightness: Increase or decrease the 10-level of
light brightness
Adjustable brightness: 100%, 50%, 25%, 10%
Adjustable speed: Increase or decrease the 10-level speed of
dynamic mode
Fade mode
Flash mode
Press to turn on the motion mode
Light turns on when get detected
Successful setting reminder: white light ash
Pressto turn off the motion mode
Successful setting reminder: white light ash
Operation(continued)
9

Detects motion up to 6.5ft
NOTICE:
Controller Operation
Operation(continued)
Set the switch to AUTO to activate the motion sensor on
the controller(B).
Press the power button to turn on and off the light
10

11
Use a soft, dry cloth to clean the strip light. Do not use alcohol-based cleaners, as this
may damage the light surface.