Eco-Smart ECO POU 3.5 User manual

ECOSMART TROUBLE SHOOTING GUIDE
MODELS ECO POU 3.5 - 6
THIS STEP BY STEP TROUBLE SHOOTING GUIDE IS DESIGNED FOR
THE INSTALLER IF ANY ISSUES ARISE WITH TANKLESS WATER
HEATER.
Downloaded from https://gadgetsgo.com/Ecosmart-POU-6-small-tankless-water-heater.html
GadgetsGo is one of the first Authorized Ecosmart Dealers, since 2010.

Step by Step Trouble Shooting Guide
This Guide is for Use by Qualified Electrical Professional
This Trouble Shooting Guide will take you through simple steps to determine
any problems or issues with unit. This Guide takes you through a sequence
of steps that MUST be followed. Skipping around might not determine the
exact problem, therefore you MUST follow the sequence.
All Ecosmart units have a simple design and are very easy to check with the
use of a MULTI CLAMP METER able to measure both Voltage and Amperage.
Below is a picture of an open view of an ECO POU 3.5-6
ECOSMART TANKLESS WATER HEATER.
Follow the steps as described and write down the readings /results on the
back pages so when contacting Technical Support you have the information
in hand.
You can contact our Technical Support at 877-474-6473 Mon-Fri 8:00 am—5:00 pm. EST
ECO POU 3.5@110V
ECO POU 6.0@208V
Downloaded from https://gadgetsgo.com/Ecosmart-POU-6-small-tankless-water-heater.html
GadgetsGo is one of the first Authorized Ecosmart Dealers, since 2010.

DISCONNECT ALL POWER TO UNIT BEFORE REMOVING
COVER.
ELECTRICAL CONNECTION
POU ARE SUPPLIED WITH A 2 PRONE TERMINAL BLOCK AND ATTACHED
CABLES.
SUPPLIED CABLES MUST BE CONNECTED TO AN INDEPENDENT SINGLE OR
DOUBLE POLE BREAKER DEPENDING ON THE MODEL.
IN ORDER TO MAKE SURE THE WIRING IS CONNECTED CORRECTLY
PERFORM THE FOLLOWING TEST.
ONCE THE CABLES HAVE BEEN SECURELY ATTACHED TO BREAKER TURN
POWER ON TO UNIT. MEASURE THE VOLTAGE GOING TO TERMINAL
BLOCK.
IF POWER GOING TO THE UNIT IS NOT CORRECT, THE UNIT WILL NOT
OPERATE CORRECTLY, SO IT IS IMPORTANT TO PERFORM THIS TEST
FIRST, BEFORE PROCEEDING .
IF NO VOLTAGE THE PROBLEM IS NOT AT THE UNIT, BUT AT YOUR ELEC-
TRICAL PANEL , OR BREAKERS.
NOW THAT WE HAVE VERIFIED THAT THE ELECTRICAL CONNECTIONS ARE
CORRECT, LETS CONTINUE.
Downloaded from https://gadgetsgo.com/Ecosmart-POU-6-small-tankless-water-heater.html
GadgetsGo is one of the first Authorized Ecosmart Dealers, since 2010.

VERIFYING SAFETY THERMOSTATS
THE FOLLOWING STEP WILL VERIFY POWER IS GOING THROUGH THE
SAFETY THERMOSTATS.
IF THE THERMOSTAT IS DAMAGED THE HEATING ELEMENT WILL NOT
FUNCTION OR HEAT UP.
TO VERIFY THE THERMOSTAT YOU NEED TO HAVE THE BREAKER TURNED
ON. YOU WILL PERFORM THIS TEST WITH YOUR VOLT METER.
THIS TEST WILL VERIFY THAT ELECTRICAL POWER IS GOING TO THE BOTTOM AND ACROSS THE THER-
MOSTAT.
USING YOUR VOLT METER YOU NEED TO PLACE ONE PROBE AT THE BOTTOM METAL PART OF THE THER-
MOSTAT AND THE OTHER PROBE NEEDS TO BE GROUNDED.
THEN PERFORM THE SAME TEST ON THE TOP PART OF THE THERMOSTAT.
ALL READING ON THIS TEST SHOULD BE IN THE 110-115V RANGE.
AGAIN, YOU MEASURE CURRENT GOING INTO BOTTOM OF THERMOSTAT TO GROUND AND THEN THE TOP
PART OF THERMOSTAT TO GROUND TO ENSURE THE THERMOSTAT IS IN GOOD WORKING CONDITION.
VERIFYING HEATING ELEMENTS
THE FOLLOWING STEP WILL VERIFY THE HEATING ELEMENTS ARE WORKING CORRECTLY.
THE HEATING ELEMENTS WILL ONLY DRAW VOLTAGE WHEN HOT WATER IS
BEING USED . WHEN HOT WATER IS DEMANDED THE ELEMENTS WILL IN-
STANTLY DRAW VOLTAGE.
THERE ARE TWO RED WIRES CONNECTED TO THE TOP OF THE ELEMENT. IN
ORDER TO CHECK IF THE ELEMENT IS WORKING YOU MUST TURN ON A HOT
WATER TAP. THIS WAY THE ELEMENTS WILL DRAW VOLTAGE AND CAN BE
CHECKED.
ONCE YOU HAVE WATER RUNNING THROUGH THE UNIT THE LED DISPLAY
WILL LIGHT UP AND DISPLAY THE TEMPERATURE SETTING ON THE UNIT.
USING YOUR VOLT METER-PLACE ONE PROBE ON ONE SCREW AND THE
OTHER PROBE ON THE OTHER SCREW LOCATED ON THE TOP OF THE ELE-
MENT. CHECK WHAT VOLTAGE YOU ARE DRAWING.
WHEN MEASURING VOLTAGE ACROSSS THE TOP OF THE ELEMENTS YOU
WILL GET A VOLTAGE READING.
REMEMBER– YOU MUST HAVE WATER RUNNING IN ORDER FOR THE ELEMENTS TO ACTIVATE AND DRAW
POWER.
IF YOUR LED DISPLAY IS LID AND YOU HAVE WATER RUNNING THROUGH THE UNIT AND HAVE 0 VOLT-
AGE READING WHEN MEASURING WITH PROBES ON EACH SCREW -PERFORM THE SAME TEST, BUT THIS
TIME PLACING ONE PROBE ON ONE SCREW AND THE OTHER PROBE TO GROUND. DO THE SAME ON THE
OTHER SCREW. IF YOU ARE GETTING VOLTAGE READINGS WHEN TESTING ON ONE SCREW TO GROUND
BUT NO VOLTAGE WHEN MEASURING FROM SCREW TO SCREW YOUR ELEMENT MIGHT BE BAD AND MUST
BE REPLACED.
You can contact our Technical Support at 877-474-6473 Mon-Fri 8:00 am—5:00 pm. EST
Downloaded from https://gadgetsgo.com/Ecosmart-POU-6-small-tankless-water-heater.html
GadgetsGo is one of the first Authorized Ecosmart Dealers, since 2010.

AMPERAGE DRAW
THIS TEST IS TO MEASURE AMPERAGE DRAW ON ELEMENT. THIS IS
DONE BY USING THE CLAMP PORTION OF THE METER AND CLAMPING
AROUND THE RED WIRE THAT GOES TO HEATING ELEMENT.
WHILE WATER IS RUNNING GET THE AMPERAGE DRAW FOR ELEMENT.
IT IS IMPORTANT TO FOLLOW THESE STEPS AND WRITE DOWN THE
READINGS/RESULTS.
THESE STEPS WILL ASSIST IN A QUICK RESOLUTION TO ANY ISSUES
YOU MIGHT HAVE WHEN CONTACTING OUR TECHNICAL SUPPORT
DEPARTMENT.
THE LAST PAGE IS DESIGNED TO DOCUMENT ALL READINGS
SHOULD YOU HAVE ANY QUESTIONS BEFORE , DURING OR AFTER IN-
STALLATION YOU CAN CONTACT OUR TECHNICAL SUPPORT DEPARTMENT
TOLL FREE AT 877-474-6473
Email: [e-mail]
Or visit our web site at
www.ecosmartus.com
Downloaded from https://gadgetsgo.com/Ecosmart-POU-6-small-tankless-water-heater.html
GadgetsGo is one of the first Authorized Ecosmart Dealers, since 2010.

VOLTAGE AT TERMINAL BLOCK L1________ L1________
VOLTAGE AT THERMOSTATS
TOP__________
BOTTOM__________
VOLTAGE AND AMPERAGE AT HEATING ELEMENTS
SCREW/SCREW___________
AMPS ___________
Downloaded from https://gadgetsgo.com/Ecosmart-POU-6-small-tankless-water-heater.html
GadgetsGo is one of the first Authorized Ecosmart Dealers, since 2010.