Ecolink CS-102 User manual

© 2020 Ecolink Intelligent Technology Inc. PN: CS102 Manual Rev 1.00
CS-102 Four Button Wireless Remote Users Guide and
Manual
The Ecolink 4‐Button Keyfob Remote communicates with the
ClearSky controller on the 345 MHz frequency. The keyfob is
a lithium coin cell, battery powered, wireless keyfob designed
to fit on a key chain, in a pocket, or in a purse. It gives users
the ability to turn the security system function ON and OFF
before entering the home or after exiting. When the control
panel and keyfob are configured, and there is an emergency,
you can turn on the siren and automatically call the central
monitoring station. Keyfobs can also operate control panel
auxiliary functions when configured.
It provides a convenient option for the following system
operations:
•Arm the system AWAY (all zones)
•Arm the system STAY (all zones except interior
follower zones)
•Arm the system with no entry delay (if programmed)
•Disarm the system
•Trigger panic alarms
Verify that the package includes the following:
•1—4‐Button Keyfob Remote
•1—Lithium Coin Battery CR2032 (included)
Figure 1: 4‐Button Keyfob Remote
Controller programming:
Note: Refer to the latest instructions for the controller or
security system being used to learn in/program your new
keyfob.
Learn In: When learning the keyfob into the ClearSky
controller, press the Arm Stay button and the Aux button
simultaneously.
Once the keyfob has been properly learned in, test the
keyfob by testing each of the keyfobs standard functions:
•Disarm button. Hold for two (2) seconds to disarm the
Control Panel. All zones except life safety are disarmed.
•Away button. Hold for two (2) seconds to arm the Control
Panel in Away mode. All zones are armed.
•Stay button. Hold for two (2) seconds to arm the Control
Panel in Stay mode. All zones except interior follower are
armed.
•Auxiliary button. If programmed, can trigger a pre‐selected
output. See the Control Panel’s Installation & Programming
Guide for details.
•Away & Disarm buttons. If programmed, pressing BOTH the
Away and Disarm buttons at the same time, will send one of
four types of emergency signals: (1)
auxiliary panic (paramedics); (2) audible alarm (police); (3)
silent panic (police); or (4) fire (fire department).
Programmable Options
The Ecolink 4‐Button Keyfob Remote (Ecolink‐CS‐102) has
alternate programable configurations that can be enabled by
the end user.
To enter configuration mode:
Press and hold Arm Away button and AUX button at the
same time until led blinks.
Configuration option 1:Press the AWAY button to enable 1
second press required to send transmission from all buttons.
Configuration option 2:Press the DISARM button to enable a
3second delay for the AUX button.
Configuration option 3:Press AUX button one time. (This sets
the keyfob for press and hold 3seconds ofthe AUX button to
initiate panic alarm RF signal instead ofholding the ARM
AWAY and DISARM buttons. NOTE: The panic RFsignal is then
processed by panel. Itwill be 4‐5 seconds before audible
alarm. • Exit programming and test keyfob by pressing AUX
button for 3 seconds. Watch keyfob LED for a blink. This
indicates the RF signal has been sent tothe panel. Alarm will
occur atthis point.
Arm Away
Disarm
Arm Stay
Aux

PN: CS102 Manual Rev 1.00
Replacing the Battery
When the battery is low a signal will be sent to the control
panel, or when a button is pressed the LED will
appear dim or will not turn on at all. Follow these simple
steps to replace the battery
1. With a key or small screwdriver, push up on the black tab
located at the bottom of the remote (fig.1)
and slide the chrome trim off.
2. Carefully separate the front and back piece of plastic to
reveal the battery
3. Replace with a CR2032 battery ensuring the + side of the
battery faces up (fig.2)
4. Re‐assemble the plastics and ensure they click together
5. Ensure the notch in the chrome trim is aligned with the
back of the plastic. It will only go on one way.
(fig.3)
Figure 1 Figure 2 Figure 3
FCC Compliance Statement
This equipment hasbeen tested and found tocomply with the limits
for Class B digital devices, pursuant
to Part 15of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
These limits are designed toprovide reasonable protection against
harmful interference ina residential installation. This equipment
generates uses and can radiate radio frequency
energy and, ifnotinstalled and used in accordance with the instruction
manual, may cause harmful
interference to radio communications. However, there is noguarantee
that interference will not occur ina
particular installation. Ifthis equipment does cause harmful interference
to radio ortelevision reception,
which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the
following measures:
•Re‐orient orrelocate the receiving antenna
•Increase the separation between the equipment and receiver
•Connect the equipment toan outlet on a different circuit from
the receiver
•Consult the dealer oran experienced radio/TV contractor for
help.
© 2020 Ecolink Intelligent Technology Inc.
Warning: Changes or modifications not expressly approved
by Ecolink Intelligent Technology Inc. could void the user’s
authority to operate the equipment.
This device complies with Industry Canada licence‐exempt
RSS standard(s). Operation is subject tothe
following two conditions: (1) this device may not cause
interference, and (2) this device must accept any
interference, including interference that may cause undesired
operation of the device.
C’et appareil est conforme lanorme d'Industrie Canada
exempts de licence RSS. Son fonctionnement est
soumis aux deux conditions suivantes: (1) c’et appareil ne
peut pas provoquer d'interférences, et (2) c’et
appareil doit accepter toute interférence, y compris les
interférences qui peuvent causer un mauvais
fonctionnementdeladispositif.
FCC ID: XQC-CS102 IC: 9863B-CS102
Warranty
Ecolink Intelligent Technology Inc . warrants that for a period of 5 years from
the date ofpurchase that this product is free from defects in material and
workmanship. This warranty does not apply todamage caused by shipping or
handling, ordamage caused by accident, abuse, misuse, misapplication,
ordinary wear, improper maintenance, failure to follow instructions or asa
result ofany unauthorized modifications.
If there is a defect in materials and workmanship under normal use within
the warranty period Ecolink Intelligent Technology Inc. shall, atits option,
repair or replace the defective equipment upon return ofthe equipment to
the original point ofpurchase.
The foregoing warranty shall apply only to the original buyer, and is and shall
be in lieu of any and all other warranties, whether expressed or implied and
of all other obligations or liabilities onthe part ofEcolink Intelligent
Technology Inc. neither assumes responsibility for, nor authorizes any other
person purporting to act on its behalf to modify or to change this warranty,
nor to assume for it any other warranty or liability concerning this product.
The maximum liability for Ecolink Intelligent Technology Inc. under all
circumstances for any warranty issue shall be limited to a replacement ofthe
defective product . Itis recommended that the customer check their
equipment on a regular basis for proper operation.
© 2020 Ecolink Intelligent Technology Inc.
2055 Corte Del Nogal
Carlsbad, California 92011
1‐855‐632‐6546
www.discoverecolink.com