Ecolink CS-902 User manual
ClearSky CHIME + SIREN
Setup Guide
Model: CS-902
1.
Thanks for choosing
Ecolink’s ClearSky
Chime + Siren. You’ve made
a sound investment!
LED Indicator
Pair Button
Volume Down
Volume Up
microSD slot
2.
Pair your ClearSky
CHIME+SIREN with your
ClearSky Bridge
1. Press the learn
button on the back of
the ClearSky Bridge.
2. Plug the
Chime+Siren into the
AC outlet.
3. Once your ClearSky Chime+Siren is
successfully paired, it will blink a green
LED and play a chime sound.
3.
Conguring Sound Effects
The ClearSky Bridge features different
sounds you can use for the following events:
Chime Notications
Alarms
Entry Delay
Exit Delay
Security Modes
To congure your Chime+Siren to
use different sound effects for
chimes or alarms, please scan the
QR code below for additional
instructions.
4.
Custom sound effects
The ClearSky Chime+Siren features a
microSD input to allow you to play your own
custom sounds.
Custom sounds
To congure your Chime+Siren to
use custom sound effects, please
scan the QR code below for
additional instructions.
Default Sound Effects
These are the default sound effects
included with your Chime + Siren
1. Chime 1
2. Chime 2
3. Chime 3
4. Chime 4
5. Chime 5
6. Chime 6
7. Chime 7
8. Chime 8
9. Chime 9
10. Chime 10
11. Chime 11
12. Chime 12
13. Alarm Siren 1
14. Exit Delay
15. Entry Delay
16. Smoke Alarm
17. CO Alarm
18. Armed Away
19. Armed Home
20. Disarmed
21. Front Door
22. Side Door
23. Back Door
24. Garage Door
25. Alarm Siren 2
26. Alarm Siren 3
27. Doorbell 1
28. Doorbell 2
29. Doorbell 3
30. Doorbell 4
For more support, please go to
www.EcolinkClearSky.com
PN: CS-902-MA03
CS-902 ClearSky Chime+Siren
Specifications
Frequency: 345MHz & 2.4 GHz Operating Temperature: 32°-120°F
Power: 120VAC, 60Hz, 0.25A Max US Operating Humidity: 5-95% RH
Decibel Rating: 105 dB @ Max Volume Indoor Use Only
The ClearSky Chime+Siren will play designated Chime and Siren sound effects
when used with a ClearSky Bridge.
To test the Chime+Siren, power the device on and press the volume buttons on
the side to verify functionality.
FCC ID: XQC-CS902 IC: 9863B-CS902
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for Class B digital devices,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Re-orient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment to an outlet on a different circuit from the receiver
• Consult the dealer or an experienced radio/TV contractor for help.
Warning: Changes or modifications not expressly approved by Ecolink Intelligent Technology
Inc. could void the user’s authority to operate the equipment.
PN: CS-902-MA03
IC Compliance Statement
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of the device.
C’et appareil est conforme la norme d'Industrie Canada exempts de licence RSS. Son
fonctionnement est soumis aux deux conditions suivantes: (1) c’et appareil ne peut pas
provoquer d'interférences, et (2) c’et appareil doit accepter toute interférence, y compris les
interférences qui peuvent causer un mauvais fonctionnement de la dispositif.
Warranty
Ecolink Intelligent Technology Inc. warrants that for a period of 1 year from the date of
purchase that this product is free from defects in material and workmanship. This warranty
does not apply to damage caused by shipping or handling, or damage caused by accident,
abuse, misuse, misapplication, ordinary wear, improper maintenance, failure to follow
instructions or as a result of any unauthorized modifications.
If there is a defect in materials and workmanship under normal use within the warranty period
Ecolink Intelligent Technology Inc. shall, at its option, repair or replace the defective
equipment upon return of the equipment to the original point of purchase.
The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any
and all other warranties, whether expressed or implied and of all other obligations or liabilities
on the part of Ecolink Intelligent Technology Inc. neither assumes responsibility for, nor
authorizes any other person purporting to act on its behalf to modify or to change this
warranty, nor to assume for it any other warranty or liability concerning this product.
The maximum liability for Ecolink Intelligent Technology Inc. under all circumstances for any
warranty issue shall be limited to a replacement of the defective product. It is recommended
that the customer check their equipment on a regular basis for proper operation.
2055 Corte Del Nogal
Carlsbad, California 92011
1-855-632-6546
www.EcolinkClearSky.com
© 2020 Ecolink Intelligent Technology Inc.
