Edelbrock 68812 User manual

Catalog #68812, #68813
©2006 Edelbrock Corporation
Page 1 of 2 Brochure #63-68812
Rev. 5/06 - DA/mc
TUBULAR EXHAUST SYSTEM
For 1981-1991 AMC Grand Wagoneer,
360 C.I.D. V8, Auto Transmission, 2 & 4 WD
Catalog #68812, #68813
INSTALLATION INSTRUCTIONS
Please study these instructions carefully before installing your new Tubular Exhaust System (TES). If you have any
questions, please contact our Technical Hotline at : 1-800-416-8628 from 7 am - 5pm, Monday-Friday, Pacific
Standard Time or e-mail us at [email protected]. Please fill out and mail your warranty card.
TUBULAR EXHAUST SYSTEM: These components are designed as a system to improve the exhaust efficiency of the AMC
V8 engine. A performance gain can be expected by the installation of the system. This system does not require welding
for installation and retains all O.E.M. emissions equipment.
Suggested Tools Needed for Installation: This vehicle has some metric fasteners.
❑ 3/8” ratchet socket set with extensions and universal 13mm and 15mm swivel sockets
❑Combination set of open-end wrenches
❑ Jackstands, screwdrivers, pliers, crescent wrench, etc.
❑Liquid penetrant, (GM #1052627) anti-seize compound (GM #5613695)
SPECIAL NOTICE: This Edelbrock Tubular Exhaust System has received an Executive Order number (E.O.#) from the
California Air Resources Board (C.A.R.B.) making it legal for street use in all 50 states. To assist you with emission
equipment certification, we have included a silver fan shroud decal to help testing personnel verify the this part is a legal
replacement on the vehicle for which it is cataloged. The adhesive-backed decal should be affixed next to the existing
emission and engine specifications decal. Do not cover any part of your original emission decal.
WARNING: The use of "Thermal Wrap" or any aftermarket coating process will void the warranty on your Edelbrock
Tubular Exhaust Systems. Those products can cause excessive heat and moisture buildup resulting in corrosion and
failure of the system.
NOTE: High temperature spark plug wires and boots are recommended to withstand heat from T.E.S.
IMPORTANT NOTE:
Proper installation is the responsibility of the installer. Improper installation will void warranty and may
result in poor performance and engine or vehicle damage.
Qty. Description
❑1Header left side #25-9435 (#68812)
❑1Header right side #25-9434 (#68812)
❑1Header left side #25-9043 (#68813)
❑1Header right side #25-9044 (#68813)
❑1Extension pipe right side #25-9540
❑1Extension pipe left side #25-9539
❑ 12 Header bolts; 3/8”-16 x 1”
❑ 1Flange
❑ 1U-Bolt; 2-1/4”
Qty. Description
❑ 2Port flange gaskets
❑ 11-Hole Gasket
❑ 1D-Nut gasket
❑ 8Bolts; 5/16”-18 x 1”
❑ 2Hex bolts; 3/8”-16 x 2”
❑ 2Hex bolts; 3/8”-16 x 3”
❑ 8Washers; 5/16”
❑ 8Lock washers; 5/16”
❑16 Lock washers; 3/8”
KIT CONTENTS
Catalog #68812 (Ceramic-Coated), #68813 (Ti-Tech Coated)

Catalog #68812, #68813
©2006 Edelbrock Corporation
Page 2 of 2 Brochure #63-68812
Rev. 5/06 - DA/mc
DISASSEMBLY - LEFT SIDE
1. Disconnect negative cable from battery.
2. Use penetrating oil on all nuts and bolts to be
removed. This will prevent the possibility of broken
or stripped nuts and bolts.
3. Remove air cleaner system (note position of line and
hose connections).
4. Disconnect A.I.R. (air injection reactor) tube from
exhaust manifold.
5. Remove bolts and exhaust manifold.
DISASSEMBLY - RIGHT SIDE
1. Disconnect A.I.R. injection tube from exhaust
manifold.
2. Remove bolts and exhaust manifold.
3. Clean exhaust flange surfaces on cylinder heads at
this time.
DISASSEMBLY - CROSSOVER PIPE
1. Raise vehicle and support with jackstands.
2. Making sure the converter is cool, remove the
exhaust crossover pipe. If the pipe is frozen to the
converter, it can be heated with a Propane torch (or
equivalent) to help loosen the joint.
INSTALLATION INSTRUCTIONS
Edelbrock Corporation, 2700 California St., Torrance, CA 90503
Tech Line: 1-800-416-8628
E-Mail: [email protected]
ASSEMBLY- LEFT SIDE
1. Install T.E.S. flange gasket and one 3/8"- 16 x 1"
bolt, lock washer, and flat washer at rearmost bolt
hole (leave bolt loose enough to accept T.E.S.).
2. Install left side T.E.S. manifold from top side.
3. Install all bolts and washers on left side. Align all
parts and tighten left side bolts and nuts at this time.
ASSEMBLY- RIGHT SIDE
1. Install T.E.S. flange gasket and one 3/8"- 16 x 1"
bolt, lock washer and flat washer at rearmost bolt
hole (leave bolt loose enough to accept T.E.S.).
2. Install right side T.E.S. manifold from below.
3. Install remaining bolts and lock washers.
4. Align all parts and tighten all right side bolts at this
time.
5. Remove A.I.R. check valves from original manifolds
and re-install them on T.E.S. Re-connect all A.I.R.
injection hoses at this time.
CROSSOVER PIPE ASSEMBLY
1. Slip new Edelbrock T.E.S crossover (Y-pipe) over
catalytic converter.
2. Install crossover pipe assembly on vehicle using two
3/8"x 3" bolts on right side to hold pipe flare against
heat riser valve and valve against manifold flange,
with flat gasket between heat riser and manifold.
Use two 3/8" x 2" bolts and the donut gasket to
attach the left side pipe to the manifold.
3. Install U-clamps and tighten all nuts and bolts.
4. Lower vehicle to the ground.