Eden SOFT-ECM NC User manual

|
SOFT
SOFT-ECM
2015-3
Installation, operation
and maintenance manual

It is compulsory to carefully read this Instruction manual before any operation on the machine: serious damages to persons and thinks could occur
if operated by non-qualied personnel.
!
All single components of machine are subject to quality and dimensioning checks during production process.
All maintenance, regulation and replacement operations described in this Instruction manual are to be only performed after stopping and separat-
ing the machine from power supply and hydraulic circuit.
While installation/maintenance operations, the operator must wear protection gloves.
Operator must wear special antiskid and resistant shoes.
Protections have been set up by the Manufacturer in order to physically protect operator while performing its tasks. Do not remove protections for
any reason, during operation. If removed must absolutely be restored.
Persons not involved in installation/maintenance operations, if any, should neither transit nor stop close to the operation area.
Electric energy and grounding systems are to be connected by expert and qualied personnel, in compliance with standards in force.
!
It is recommended to protect main power supply line by safety switches (overload switches).
Any magnetic or electromagnetic eld in the nearby could affect proper operation of control panel. Environmental temperature and humidity are the
best conditions to properly operate machines.
Ensure that electric circuit is suitably protected and complies with motor characteristics: the machine is equipped with an identication plate,
specifying power, frequency and power supply voltage values. Also ensure that grounding has been performed and a differential switch is regularly
installed upstream of power supply cable. The Manufacturer is not responsible for damages to persons or things provoked by wrong or unsuitable
grounding.
Before performing regulation, maintenance and/or replacement operations, the operator must wait for a time-period after machine stop.
MAIN WARNINGS TO MACHINE USE

Vers. 2015-3
3
INSTALLATION, OPERATION
AND MAINTENANCE MANUAL
water cassette
SOFT / SOFT-ECM
FIRST PART: FOR THE INSTALLER
GENERAL DIMENSIONS FOR 2 PIPE WATER CASSETTES 4
GENERAL DIMENSIONS FOR 4 PIPE WATER CASSETTES 5
WORKING LIMITS 6
GENERAL FEATURES AND MAIN COMPONENTS 6
Structure 6
Heat exchanger 6
Air lter 6
Motor fan group 6
Décor panel 6
Elimination of condensation 6
RECOMMENDATIONS FOR THE INSTALLER 6
Unit installation 6
RECEIVING, STORE AND MOVING THE UNITS 7
INSTALLATION ACCESSORIES 7
SELECTION OF CASSETTE INSTALLATION LOCATION 7
INSTALLATION 7
Fixing the cassette 7
Fixing the panel 7
CHANGE OF AIR AND RECIRCULATION SYSTEM 7
Fresh air renewal 7
WATER CONNECTIONS 8
Standard water connection to heating/cooling system 8
Cassettes with a control board that is managed onboard 8
Cassettes with and without a control board that is managed onboard 8
INSTALLATION OF AUXILIARY DRAIN PAN 8
CONDENSATE DRAINAGE 9
ELECTRICAL CONNECTIONS 9
Access to the control panel 9
WIRING DIAGRAM:
FOR WATER CASSETTE MODEL SOFT NC 10
FOR WATER CASSETTE MODEL SOFT-ECM NC 11
FOR WATER CASSETTE MODEL SOFT RC 12
FOR WATER CASSETTE MODEL SOFT-ECM RC 13
RS485 COMMUNICATION NETWORK 14
WIRING DIAGRAM FOR WATER CASSETTE
MODEL SOFT-ECM RC MASTER/SLAVE 15
SECOND PART: FOR THE USER
RECOMMENDATION 16
INFRARED REMOTE CONTROL 17
OPERATION OF INFRARED REMOTE CONTROL 17
Clock adjustment 17
ON/OFF daily timer 17
Emergency ON/OFF button 17
Offset for T1 temperature reading calibration 18
SWING 18
Automatic version 18
Manual version 18
BATTERIES REPLACEMENT 18
EXTRAORDINARY MAINTENANCE 19
END OF SEASON MAINTENANCE 19
WHAT TO DO IF... 19
DISMANTLING THE APPLIANCE 19
INDEX

Vers. 2015-3
4
INSTALLATION, OPERATION
AND MAINTENANCE MANUAL
water cassette
SOFT / SOFT-ECM
GENERAL DIMENSIONS FOR 2 PIPE WATER CASSETTES
61 62 63 64 65
Fans number n° 1 1 1 1 1
Coil numbers n° 1 1 1 1 1
Hydraulic tting (Ø ISO 228 female gas) Ø 1/2” 1/2” 3/4” 3/4” 3/4”
Air supply in adjacent room (Ø) mm 150 150 150 150 150
Air supply in adjacent room (BxH) mm 300x150 300x150 300x150 300x150 300x150
Fresh air intake (Ø) mm 80 80 80 80 80
Fresh air intake (BxH) mm 100x45 100x45 100x45 100x45 100x45
Unit net weight kg 20 21 23 23 24
Panel net weight kg 3 3 3 3 3
Pic. 01

Vers. 2015-3
5
INSTALLATION, OPERATION
AND MAINTENANCE MANUAL
water cassette
SOFT / SOFT-ECM
GENERAL DIMENSIONS FOR 4 PIPE WATER CASSETTES
81 82 83 83C 84 84C
N. ventilatori n°111111
N. batterie n°111111
Hydraulic tting
(Ø ISO 228
female gas)
standard coil Ø 1/2” 1/2” 1/2” 1/2” 1/2” 1/2”
auxiliary coil Ø 1/2” 1/2” 1/2” 1/2” 1/2” 1/2”
Air supply in adjacent room (Ø) mm 150 150 150 150 150 150
Air supply in adjacent room (BxH) mm 300x150 300x150 300x150 300x150 300x150 300x150
Fresh air intake (Ø) mm 80 80 80 80 80 80
Fresh air intake (BxH) mm 100x45 100x45 100x45 100x45 100x45 100x45
Unit net weight kg 23 24 24 24 24 24
Panel net weight kg 3 3 3 3 3 3
Pic. 02