EdenPURE PowerPack 4000 User manual
Introduction
Thank you for purchasing the PowerPack 4000 Bathroom Heater. Each unit has been
manufactured to ensure safety and reliability.
Before using the Bathroom Heater for the first time, carefully read through this operating manual
in its entirety and keep it for future reference. This Bathroom Heater is designed for residential
use only. It is not intended for commercial or industrial settings.
PowerPack 4000 Bathroom Heater Features
•Safe for use in bathrooms (IP21 rating for protection against condensation)
•High quality PTC heating element for safe, quick heat
•Adjustable heat settings for custom controlled comfort
•Compact design makes this heater easy to move and transport
•Tip-over switch ensures safe operation
•Easy to use dial controls with LED display
Important Safety Information
Basic safety instructions must be followed before using any electrical appliance. Failure to
carefully read and follow these safety instructions can result in electric shock or fire hazard and
will void the product’s warranty.
1. The PowerPack Bathroom Heater is designed for residential use only. Any other use is not
recommended.
2. This Bathroom Heater is hot when in use. To avoid burns, do not let bare skin touch any
hot surfaces.
3. Plug the Bathroom Heater directly into a wall outlet/receptacle. Do not plug it into any
other cord connected device such as a surge protector, outlet adapter or power strip.
Using such devices can create a fire hazard.
4. Only plug the unit directly into a 120V wall outlet, and always make sure the power
source conforms to the electric requirements of this Bathroom Heater. Please note that
faulty outlet connections may cause the outlet to overheat. Always make sure the
Bathroom Heater’s plug fits tightly into the outlet before operation.
5. Use this Bathroom Heater in a room that is equipped with a functioning smoke detector.
6. Do not use this Bathroom Heater outdoors.
7. Heaters have hot and sparking parts inside. Do not use this appliance in areas where
gasoline, paint or flammable liquids are used or stored.
8. Always unplug the unit from the power supply by gripping the plug and pulling it from the
outlet. Never unplug the unit from the power supply by pulling on the Bathroom Heater’s
power cord.
9. Always unplug the unit from the power supply before moving it.
10. Always unplug the unit from the power supply before cleaning or servicing.
11. Do not use the Bathroom Heater in areas where paint, gasoline or any other flammable
substances are being used or stored.
12. Extreme caution should be exercised when using this product near children, the elderly
and pets. This Bathroom Heater should not be left unattended for extended periods of
time.
13. Do not leave children unattended when the heater is turned on or in operation, and do
not let children play with the Bathroom Heater’s packaging material.
14. Do not operate the Bathroom Heater if it has a damaged power cord. If the power cord
is damaged, it must be replaced by the manufacturer, its service agent or similarly
qualified individuals to avoid any hazards.
15. Always position this Bathroom Heater on a stable, flat and level surface to reduce the risk
of tipping or overturning. Never place the heater on soft surfaces such as beds or pillows,
as this can cause the heater’s openings to become blocked.
16. Do not place the heater on a surface where it can fall into a bathtub or container of
water.
17. If the Bathroom Heater will not be in use, place it back in its box and store it in a dry
location.
18. Do not run the power cord under carpet or cover it with rugs or runners. Always arrange
the power cord away from high traffic areas and any other area where it may be
tripped over. Make sure objects do not rest on the power cord.
19. Do not use extension cords with this Bathroom Heater.
20. Do not insert or allow fingers or objects to enter the Bathroom Heater’s ventilation or
exhaust openings. This can cause damage to the blower, or cause electric shock or fire,
and will void the manufacturer’s warranty.
21. Do not use corrosive detergents, solvents or other similar cleaning products when
cleaning the Bathroom Heater.
22. Do not place the Bathroom Heater near walls or curtains.
23. Do not use this appliance with any solid state speed control devices.
24. If this Bathroom Heater is damaged or malfunctioning, discontinue use and refer to the
troubleshooting section in this instruction manual. If the problem persists, contact
EdenPURE® for further assistance. Do not attempt to repair or disassemble the Bathroom
Heater as this will void the warranty.
25. To reduce the risk of electric shock, do not immerse, remove, modify or replace the
Bathroom Heater’s plug and do not place the unit where it may easily fall in water.
SAVE THESE INSTRUCTIONS. THIS PRODUCT IS FOR
HOUSEHOLD USE ONLY.
List of Parts
1. Control Panel
2. Wind Outlet
3. Front Cover
4. Back Cover
5. Heater Base
Use & Operation
This package contains a PowerPack 4000 Bathroom Heater. Remove the product from the box
and all included packaging materials. Keep the box for future storage and check to make sure
there is no residual packaging left over on or in any of the product’s components.
Basic Operating Instructions
•Carefully remove your Bathroom Heater from its box and save it for off-season storage.
•Make sure the Mode Control Knob is set to the OFF Mode before plugging the Bathroom
Heater into an outlet.
•To avoid overloading your circuit, do not use other high wattage appliances in the same
outlet. At 1500 watts, this heater draws 12.5 Amps.
•To start heater operation, make sure the thermostat is set to the highest position
Mode Controls
•OFF Mode –To turn the Bathroom Heater off at any time, turn the Mode Control Knob to
the OFF position (indicated by the icon with the circle)
•Fan Only Mode –To run the heater on Fan Only Mode (without heat output), turn the
Mode Control Knob to the Fan Only position (indicated by the icon with the fan)
•Low Heat –The heater will run continuously on low heat
•High Heat –The heater will run continuously on high heat at 1500 watts
Thermostat Control
•Before setting the thermostat, allow the Bathroom Heater to operate and warm up your
room. As noted above, to turn on the unit, make sure the thermostat is set to the highest
position.
•Once the desired temperature comfort level is reached, lower the thermostat setting
until the Bathroom Heater stops operating. This is done by moving the Thermostat Control
Knob to lower settings.
•The thermostat will now automatically maintain the pre-set temperature by cycling the
heater ON and OFF.
•Please note that it is normal for the Bathroom Heater to cycle on and off as it maintains
your preset temperature. To prevent the unit from cycling, raise the thermostat setting.
Maintenance & Cleaning
Regular cleaning and maintenance ensures your Bathroom Heater performs without defects.
Always unplug the unit from the power outlet prior to moving or servicing.
General Maintenance Instructions
1. Always unplug the Bathroom Heater from the power supply before servicing or cleaning.
2. Dampen a clean cloth with water and use it on the exterior of the unit to remove any
dust, dirt or debris. Do not use harsh detergents, solvents or corrosive cleaners to clean
the unit, and do not let the unit’s motor and electrical components come into contact
with water.
3. Do not submerge the Bathroom Heater in water.
4. Thoroughly dry all of the Bathroom Heater’s parts with a soft cloth before reconnecting
the unit to the power supply.
5. When the Bathroom Heater will not be in use, store it in a dry area away from sunlight
and heat.
Support
If you have any questions about your Bathroom Heater or any other EdenPURE®product, please
Table of contents
Other EdenPURE Electric Heater manuals
