Edge-Core ECIS4500 Series User manual

Quick Installation Guide
www.edge-core.com
Industrial Gigabit Ethernet Switch
ECIS4500 Series

Quick Start Guide
ECIS4500 6T2F Industrial Gigabit Ethernet Switch
Industrial Gigabit Ethernet Switch
with 6 10/100/1000BASE-T ports,
2 10/100/1000BASE-X SFP slots
ECIS4500 8T2F Industrial Gigabit Ethernet Switch
Industrial Gigabit Ethernet Switch
with 8 10/100/1000BASE-T ports,
2 10/100/1000BASE-X SFP slots
ECIS4500 6T4F Industrial Gigabit Ethernet Switch
Industrial Gigabit Ethernet Switch
with 6 10/100/1000BASE-T ports,
4 10/100/1000BASE-X SFP slots
ECIS4500 4P4T Industrial Gigabit Ethernet Switch
Industrial Gigabit Ethernet Switch
with 4 10/100/1000BASE-T PoE+ ports,
4 10/100/1000BASE-T SFP slots
ECIS4500 4P2T2F Industrial Gigabit Ethernet Switch
Industrial Gigabit Ethernet Switch
with 4 10/100/1000BASE-T PoE+ ports,
2 10/100/1000BASE-T SFP ports,
plus 2 10/100/1000BASE-X SFP slots
ECIS4500 8P4F Industrial Gigabit Ethernet Switch
Industrial Gigabit Ethernet Switch
with 8 10/100/1000BASE-T PoE+ ports,
4 10/100/1000BASE-X SFP slots
ECIS4500 8P2T4F Industrial Gigabit Ethernet Switch
Industrial Gigabit Ethernet Switch
with 8 10/100/1000BASE-T PoE+ ports,
2 10/100/1000BASE-T SFP ports,
plus 4 10/100/1000BASE-X SFP slots
E092017-AP

ECIS4500 Quick Installation Guide
3
ECIS4500 Series Industrial switch
Quick Installation Guide
Overview
The managed Ethernet switch solutions are designed for supporting standard industrial
applications. The managed switches are easier to prioritize, partition, and organize user’s network,
providing a more reliable and better quality services.
Package Checklist
Please verify the box contains the following items:
Item Quantity
Management Ethernet switch 1
Console Cable* 1
Wall-mount plates 2
DIN-rail clip 1
M3 Screws (for the wall mount plates and DIN clip) 4
DC power terminal block 1
RJ-45 Ethernet port dust cover Same as RJ-45 port number
SFP Ethernet port dust cover Same as SFP port number
* Please use the console cable in the accessory to configure switch in console mode.

ECIS4500 Quick Installation Guide
4
Safety Instructions
Overview
When a fiber connection is removed during installation, testing, servicing or an active fiber is broken,
ocular exposure to optical energy may be potentially hazardous, depending on the laser output
power.
The primary hazards of exposing laser radiation from an optical-fiber communication systems are:
● Damage to eyes from accidental exposure to a beam emitted by a laser source.
● Damage to eyes from viewing the connector that attaches to a broken fiber or an energized fiber.
Technical Specifications
Model ECIS4500 Series Industrial Switch
Ethernet Copper RJ-45 Ports 10/100/1000 Mbps speed auto- negotiation MDI/MDIX Auto-crossover
SFP (pluggable Ports) 100/1000BASE SFP slot
Fiber port connector LC typically for fiber (depends on module)
Power ECIS4500-6T2F ECIS4500-4P4T
ECIS4500-8T2F ECIS4500-4P2T2F
ECIS4500-6T4F ECIS4500-8P4F
ECIS4500-8P2T4F
Power input Redundant input terminals; reverse power protection
Input voltage range 12-58 VDC 12-58 VDC (with PoE: 46-58 VDC)
Maximum Power consumption 17 Watts Without PoE: 14 Watts,
With PoE: 265 Watts
Environmental and Compliances
Operating temperature -40 to +75°C (cold startup at -40°C)
Storage temperature -40 to +85°C
Humidity 5 to 95% RH (non-condensing)
Mechanical
Ingress protection IP30
Dimension
(without DIN rail clip) 154mm (H) x 109mm (D) x 60mm (W) 154mm (H) x 128mm (D) x 77mm (W)
Weight 1056 g 1410 g
Installation option DIN-rail and wall mounting

ECIS4500 Quick Installation Guide
5
Appearance
ECIS4500-6T4F/8T2F/6T2F
ECIS4500-8P2T4F/8P4F/4P2T2F/4P4T

ECIS4500 Quick Installation Guide
6
Faceplate
ECIS4500-8T2F ECIS4500-6T2FECIS4500-6T4F
ECIS4500-8P2T4F ECIS4500-8P4F ECIS4500-4P2T2F ECIS4500-4P4F

ECIS4500 Quick Installation Guide
7
DIN-rail mounting
Mounting steps:
1. Screw the din-clip with screws in the accessory kit.
2. Hook the unit onto the din-rail.
3. Push the bottom of the unit towards the din-rail until it locks in place.
Wall mounting
Mounting steps:
1. Screw the wall-mount brackets with screws in the accessory kit.
The graph is for all series

ECIS4500 Quick Installation Guide
8
Ethernet Interface (RJ-45 Ethernet)
The switch provides two types of Ethernet interfaces: electrical (RJ-45) and optical (SFP) interfaces.
Connecting the Ethernet interface via RJ-45:
● To connect the switch to a PC, use straight-through or cross-over Ethernet cables,
● To connect the switch to an Ethernet device, use UTP (Unshielded Twisted Pair) or STP (Shielded
Twisted Pair) Ethernet cables.
The pin assignment of RJ-45 connector is shown in the following figure and table.
ECIS4500-6T2F/6T4F/8T2F
ECIS4500-8P2T4F/8P4F/4P2T2F/4P4T
Ethernet Interface (Fiber, SFP)
For both 100/1000 Mbps fiber speed connections, the SFP slots are available. The SFP slot accepts the
fiber transceivers that typically have an LC connector.
The fiber transceivers have options of multimode, single mode, long-haul or special-application
transceivers.
DANGER: Never attempt to view optical connectors that might be emitting laser energy.
Do not power up the laser product without connecting the laser to the optical fiber and
putting the dust cover in position, as laser outputs will emit infrared laser light at this point.
Pin Assignment PoE Assignment
1,2 T/Rx+,T/Rx- Positive VPort
3,6 T/Rx+,T/Rx- Negative VPort
4,5 T/Rx+,T/Rx- X
7,8 T/Rx+,T/Rx- X
Pin Assignment
1,2 T/Rx+,T/Rx-
3,6 T/Rx+,T/Rx-
4,5 T/Rx+,T/Rx-
7,8 T/Rx+,T/Rx-

ECIS4500 Quick Installation Guide
9
Connecting Power Terminal Block
The switch can be powered from two power supplies (input range 12V – 58V). Insert the
positive and negative wires into V+ and V- contacts on the terminal block respectively and
tighten the wire-clamp screws to prevent the wires from being loosened.
Note: 1. The DC power should be connected to a well-fused power supply.
ECIS4500-6T4F/6T2F/8T2F
ECIS4500-8P2T4F/8P4F/4P2T2F/4P4F
First Power Supply Second Power Supply
First Power Supply
Second Power Supply

ECIS4500 Quick Installation Guide
10
Alarm Relay and Ground
The alarm relay output contacts are in the middle of the DC terminal block connector as shown in the
figure below.
The alarm relay out is “Normal Open”, and it will be closed when detected any predefined failure such
as power failures or Ethernet link failures.
The relay output with current carrying capacity of 0.5 A @ 24 VDC
Console Connection
The Console port is for local management by using a terminal emulator or a computer with terminal
emulation software.
● DB9 connector connect to computer COM port
● Baud rate: 115200bps
● 8 data bits, 1 stop bit
● None Priority
● None flow control
Ground Connector