Edge-Core ES3510MA-DC Programming manual

Management Guide
www.edge-core.com
8-Port Layer 2
Fast Ethernet Switch

M ANAGEMENT G UIDE
ES3510MA-DC FAST ETHERNET SWITCH
Layer 2 Switch
with 8 10/100BASE-TX (RJ-45) Ports,
and 2 Gigabit Combination Ports (RJ-45/SFP)
ES3510MA-DC
E122010/ST-R01
150200000251A

– 5 –
ABOUT THIS GUIDE
PURPOSE This guide gives specific information on how to operate and use the
management functions of the switch.
AUDIENCE The guide is intended for use by network administrators who are
responsible for operating and maintaining network equipment;
consequently, it assumes a basic working knowledge of general switch
functions, the Internet Protocol (IP), and Simple Network Management
Protocol (SNMP).
CONVENTIONS The following conventions are used throughout this guide to show
information:
N OTE : Emphasizes important information or calls your attention to related
features or instructions.
C AUTION : Alerts you to a potential hazard that could cause loss of data, or
damage the system or equipment.
W ARNING : Alerts you to a potential hazard that could cause personal injury.
RELATED PUBLICATIONS The following publication details the hardware features of the switch,
including the physical and performance-related characteristics, and how to
install the switch:
The Installation Guide
Also, as part of the switch’s software, there is an online web-based help
that describes all management related features.
REVISION HISTORY This section summarizes the changes in each revision of this guide.
DECEMBER 2010 RELEASE
This is the second release of this guide. This guide is valid for software
release v1.2.4.2.

A BOUT T HIS G UIDE
– 6 –

– 7 –
CONTENTS
ABOUT THIS GUIDE 5
CONTENTS 7
FIGURES 35
TABLES 45
SECTION I GETTING STARTED 51
1INTRODUCTION 53
Key Features 53
Description of Software Features 54
System Defaults 59
2INITIAL SWITCH CONFIGURATION 63
Connecting to the Switch 63
Configuration Options 63
Required Connections 64
Remote Connections 65
Basic Configuration 66
Console Connection 66
Setting Passwords 66
Setting an IP Address 67
Downloading a Configuration File Referenced by a DHCP Server 73
Enabling SNMP Management Access 75
Managing System Files 77
Saving or Restoring Configuration Settings 78
SECTION II WEB CONFIGURATION 81
3USING THE WEB INTERFACE 83
Connecting to the Web Interface 83

C ONTENTS
– 8 –
Navigating the Web Browser Interface 84
Home Page 84
Configuration Options 85
Panel Display 85
Main Menu 86
4BASIC MANAGEMENT TASKS 99
Displaying System Information 99
Displaying Hardware/Software Versions 100
Configuring Support for Jumbo Frames 102
Displaying Bridge Extension Capabilities 103
Managing System Files 104
Copying Files via TFTP or HTTP 104
Saving the Running Configuration to a Local File 106
Setting The Start-Up File 107
Showing System Files 108
Automatic Operation Code Upgrade 109
Setting the System Clock 113
Setting the Time Manually 113
Setting the SNTP Polling Interval 114
Specifying SNTP Time Servers 115
Setting the Time Zone 116
Console Port Settings 117
Telnet Settings 119
Displaying CPU Utilization 120
Displaying Memory Utilization 121
Resetting the System 122
5INTERFACE CONFIGURATION 127
Port Configuration 127
Configuring by Port List 127
Configuring by Port Range 130
Displaying Connection Status 131
Configuring Local Port Mirroring 132
Configuring Remote Port Mirroring 134
Showing Port or Trunk Statistics 138
Performing Cable Diagnostics 142

C ONTENTS
– 9 –
Trunk Configuration 144
Configuring a Static Trunk 145
Configuring a Dynamic Trunk 147
Displaying LACP Port Counters 152
Displaying LACP Settings and Status for the Local Side 154
Displaying LACP Settings and Status for the Remote Side 155
Saving Power 156
Traffic Segmentation 158
Enabling Traffic Segmentation 158
Configuring Uplink and Downlink Ports 159
VLAN Trunking 161
6 VLAN CONFIGURATION 165
IEEE 802.1Q VLANs 165
Configuring VLAN Groups 168
Adding Static Members to VLANs 170
Configuring Dynamic VLAN Registration 175
IEEE 802.1Q Tunneling 178
Enabling QinQ Tunneling on the Switch 182
Adding an Interface to a QinQ Tunnel 183
Protocol VLANs 184
Configuring Protocol VLAN Groups 185
Mapping Protocol Groups to Interfaces 187
Configuring IP Subnet VLANs 189
Configuring MAC-based VLANs 191
Configuring VLAN Mirroring 193
7ADDRESS TABLE SETTINGS 195
Setting Static Addresses 195
Changing the Aging Time 197
Displaying the Dynamic Address Table 198
Clearing the Dynamic Address Table 199
Configuring MAC Address Mirroring 200
8SPANNING TREE ALGORITHM 203
Overview 203
Configuring Loopback Detection 206
Configuring Global Settings for STA 207
Displaying Global Settings for STA 212

C ONTENTS
– 10 –
Configuring Interface Settings for STA 213
Displaying Interface Settings for STA 217
Configuring Multiple Spanning Trees 220
Configuring Interface Settings for MSTP 224
9RATE LIMIT CONFIGURATION 227
10 STORM CONTROL CONFIGURATION 229
11 CLASS OF SERVICE 231
Layer 2 Queue Settings 231
Setting the Default Priority for Interfaces 231
Selecting the Queue Mode 232
Mapping CoS Values to Egress Queues 235
Layer 3/4 Priority Settings 238
Setting Priority Processing to DSCP or CoS 238
Mapping Ingress DSCP Values to Internal DSCP Values 239
Mapping CoS Priorities to Internal DSCP Values 242
12 QUALITY OF SERVICE 245
Overview 245
Configuring a Class Map 246
Creating QoS Policies 249
Attaching a Policy Map to a Port 259
13 VOIP TRAFFIC CONFIGURATION 261
Overview 261
Configuring VoIP Traffic 261
Configuring Telephony OUI 263
Configuring VoIP Traffic Ports 264
14 SECURITY MEASURES 267
AAA Authorization and Accounting 268
Configuring Local/Remote Logon Authentication 269
Configuring Remote Logon Authentication Servers 270
Configuring AAA Accounting 275
Configuring AAA Authorization 280
Configuring User Accounts 283
Web Authentication 284
Configuring Global Settings for Web Authentication 285
Configuring Interface Settings for Web Authentication 286