Edimax EW-7106PC User manual

W
Wi ir re el le es ss s L LA AN N C Ca ar rd db bu us s A Ad da ap pt te er r
EW-7106PC
User Manual
Version: 3.0
(June, 2003)

COPYRIGHT
Copyright 2002/2003 by this company. All rights reserved. No part of this
publication may be reproduced, transmitted, transcribed, stored in a retrieval
system, or translated into any language or computer language, in any form or
by any means, electronic, mechanical, magnetic, optical, chemical, manual or
otherwise, without the prior written permission of this company
This company makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any
warranties, merchantability or fitness for any particular purpose. Any software
described in this manual is sold or licensed "as is". Should the programs
prove defective following their purchase, the buyer (and not this company, its
distributor, or its dealer) assumes the entire cost of all necessary servicing,
repair, and any incidental or consequential damages resulting from any defect
in the software. Further, this company reserves the right to revise this
publication and to make changes from time to time in the contents hereof
without obligation to notify any person of such revision or changes.
All brand and product names mentioned in this manual are trademarks and/or registered
trademarks of their respective holders.

Federal Communication Commission
Interference Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution
This device and its antenna must not be co-located or operating in
conjunction with any other antenna or transmitter.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the authority to operate equipment.
Federal Communications Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an
uncontrolled environment. In order to avoid the possibility of exceeding the
FCC radio frequency exposure limits, human proximity to the antenna shall
not be less than 2.5cm (1 inch) during normal operation.

Federal Communications Commission (FCC) RF Exposure Requirements
SAR compliance has been established in the laptop computer(s)
configurations with PCMCIA slot on the side near the center, as tested in the
application for Certification, and can be used in laptop computer(s) with
substantially similar physical dimensions, construction, and electrical and RF
characteristics. Use in other devices such a PDAs or lappads is not
authorized. This transmitter is restricted for use with the specific antenna(s)
tested in the application for Certification. The antenna(s) used for this
transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
R&TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE 1999/5/CE
OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of March 9, 1999 on
radio equipment and telecommunication terminal Equipment and the mutual
recognition of their conformity (R&TTE)
The R&TTE Directive repeals and replaces in the directive 98/13/EEC
(Telecommunications Terminal Equipment and Satellite Earth Station
Equipment) As of April 8, 2000.
Safety
This equipment is designed with the utmost care for the safety of those who
install and use it. However, special attention must be paid to the dangers of
electric shock and static electricity when working with electrical equipment. All
guidelines of this and of the computer manufacture must therefore be allowed
at all times to ensure the safe use of the equipment.
EU Countries Intended for Use
The ETSI version of this device is intended for home and office use in Austria,
Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy,
Luxembourg, the Netherlands, Portugal, Spain, Sweden, and the United
Kingdom.
The ETSI version of this device is also authorized for use in EFTA member
states: Iceland, Liechtenstein, Norway, and Switzerland.
EU Countries Not intended for use
None.

CONTENTS
1INTRODUCTION.............................................................................1
1.1 FEATURES .................................................................................................... 1
1.2 SPECIFICATIONS............................................................................................ 1
1.3 PACKAGE CONTENTS..................................................................................... 2
2INSTALLATION PROCEDURE .....................................................3
2.1 WINDOWS 98SE/ME/2000............................................................................. 3
2.1.1 Install the Driver ...................................................................................................... 3
2.1.2 Install the Utility...................................................................................................... 3
2.2 WINDOWS XP............................................................................................... 4
3CONFIGURATION UTILITY .........................................................7
3.1 CONNECT TO THE WIRELESS NETWORK.......................................................... 7
3.2 CONFIGURATION........................................................................................... 8
3.3 ADVANCED CONFIGURATION ....................................................................... 11
3.4 STATUS ...................................................................................................... 13
3.5 STATISTICS................................................................................................. 14
3.6 ABOUT ....................................................................................................... 15
4TROUBLESHOOTING..................................................................16

1
1 Introduction
Thank you for purchasing the Wireless LAN Cardbus Adapter. This card features the latest
innovation wireless technology. IEEE 802.1x which request wireless stations to pass the
authorization by entering a unique user name and password designated by the authorization
server before connecting to the wireless devices such as Access Point or Router. TKIP
(Temporal Key Integrity Protocol) and AES (Advanced Encryption Standard) which are
advanced WLAN security technology included in the IEEE 802.11i standard, and supports
32-bit cardbus interface which enables higher transmittion performance. Furhtermore, this
card provides several kinds of power saving modes allowing user customizes the way of
saving the power from his/her portable or handheld devices. This card is cost-effective,
together with the versatile features, it is the best solution for you to builde your wirless
network.
1.1 Features
• Complies with the IEEE 802.11b (DSSS) 2.4GHz standard.
• High-speed data transfer rate – up to 11Mbps.
• Support 64/128-bit AES/TKIP/WEP Data Encryption function for high level of security.
• Supports IEEE 802.1x advanced WLAN Security.
• Supports peer-to-peer communication among any wireless users, no Access Point required.
• Automatic rate fallback enables data security and reliability.
• Supports power save mode.
• Supports 32-bit cardbus interface.
• Supports the most popular operating systems: Windows 98SE/Me/NT/2000/XP and Linux.
• Plug and Play installation.
1.2 Specifications
• Standard: IEEE 802.11b
• Interface: 32-bit Cardbus
• Frequency Band: 2.4000 ~ 2.4835GHz (Industrial Scientific Medical Band)
• Modulation: CCK@11/5.5Mbps, DQPSK@2Mbps, DBPSK@1Mbps
• Radio Technology: Direct Sequence Spread Spectrum (DSSS)
• Data Rate: 11/5.5/2/1Mbps auto fallback
• Security:
64/128-bit WEP Encryption
64/128-bit TKIP Data Encryption
64/128-bit AES Data Encryption
IEEE 802.1x
• Antenna: Diversity Patch Antenna
• Drivers: Windows 98SE/Me/NT/2000/XP and Linux
• LEDs: TX/RX, Link
• Power Voltage: 3.3V

2
• Transmit Power: 16dBm~18dBm
• Receive Sensitivity: -83dBm (Typical)
• Dimension: 7(H) x 113(W) x 54(D)
• Temperature: 32~131 °F (0~55 °C)
• Humidity: 0-95% (NonCondensing)
• Certification: FCC, CE, Wi-Fi, WHQL
1.3 Package Contents
Before you begin the installation, please check the items of your package. The package
should include the following items:
• One Wireless Cardbus Adapter
• One CD (Driver/Utility/User’s Manual.)
• One Quick Guide
If any of the above items is missing, contact your supplier as soon as possible.

3
2 Installation Procedure
2.1 Windows 98SE/Me/2000
Before you proceed with the installation, please notice following descriptions.
Note1: The following installation was operated under Windows 2000. (Procedures will be the
same for Windows 98SE/Me.)
Note2: If you have installed the Wireless PC Card driver & utility before, please uninstall the old
version first.
2.1.1 Install the Driver
1. Insert the adapter into the Cardbus port of your computer, the system will automatically
find the device and search for its driver.
2. Please select the “Driver\Win2000” folder (select the folder based on your computer’s
OS system) and the system will complete the driver installation automatically.
2.1.2 Install the Utility
1. Insert the CD into the CD-ROM device and execute the "Utility\setup.exe" program. The
InstallShield Wizard box will appear, click "Next" to continue.
2. Follow the instruction of the installation program. The program will install the software
for this device directly.

4
3. Click "Finish" to complete the installation.
4. When you complete the Utility installation, a shortcut named “Rtl8180“ will appear in the
computer’s desktop and a new icon will display in the system tray at the bottom of the
screen. Double click the shortcut or the icon and start using the WLAN Cardbus Adapter.
In the Desktop In the system tray
2.2 Windows XP
The installation process in Windows XP is similar with the process in windows
98SE/Me/2000. Please refer to the instructions described in section 2.1.
Due to the Windows XP has built-in wireless network utility you may decide to use the
system’s utility or the one provided by this adapter. It is strongly recommended to using
the utility of this adapter.
A. Using the Windows XP’s Utility
Click the icon marked in red in the system tray and you may start using the Windows XP’s
wireless utility.

5
B. Using the Utility of this adapter
1. Get into Windows XP’s Utility, click “Advanced“ button.
2. On the “Wireless Networks“ tab in the “Wireless Network Connection Properties“ screen,
clear the “Use Windows to configure my wireless network settings“ check box. If you
want to enable the Windows XP built-in utility, select the check box again.
3. Double click the shortcut or the icon in the system tray and start using the WLAN Cardbus Adapter.

6
Note: If you don’t disable the XP’s Utility, you can still see the link status and statistics during
communication process from the adapter’s utility.

7
3 Configuration Utility
The Configuration Utility is a powerful application that helps you configure the Wireless LAN
Cardbus Adapter and monitor the link status and the statistics during the communication
process.
This utility can be used to change the following configuration parameters when the device is
active.
3.1 Connect to the Wireless Network
From the “Connect to Wireless Network” screen you are able to view available wireless
networks within range of your computer and access to the network you intend to.
Parameter Description
Available Wireless Netowrks This list shows all available wireless network within range of your
computer. If you want to connect to any network on the list, select
the network and click “Connect” button.
Network Key If the network is required for Wired Equivalent Privacy (WEP) key,
type the key in the text box. The key should be 10 or 26
hexadecimal characters according to the WEP mode setting (64-
bit or 128-bit) of the network.
Confirm Network Key Enter the same network key again to cofirm the key.
Advanced Button To configure additional wireless network setting, review the link
status and statistics or if you have difficulty connecting to a
network, click “Advanced“ button.

8
Parameter Description
Connect Button Click the button to connect to the selected network.
Cancel Button Click the button to cancel the wireless network connection.
3.2 Configuration
This screen is for you to make advanced setting in order to connect to an available network
or create a new wireless network connection. You could also define the connection order
here.
Parameter Description
Profile Display the profiles the adapter is connecting to. It also stores the
profiles that the adapter ever connected to. If you want to change
the connection to another profile, pull down the list and select the
profile you intend to connect.
Available Wireless Network(s) This list shows all available wireless network within range of your
computer. You can double click the network listed in the table to
do more configuration.

9
Parameter Description
Available Wireless Network(s)
Configure Button If you are unable to conect to an existing wireless network, click
the network name and then click this button. The “Wireless
Netowrk Properties“ will show up for you to configure the adapter
and ensure the settings are correct.
Refresh Button To update the list of available networks, click the
“Refresh“ button.
Available Profile(s) This list shows the preferred networks for the wireless connection.
You can add, remove, edit the preferred networks or set one of
the networks as the default connection.
Add Button To configurate a new profile, click “Add“ button.
Remove Button To remove a wireless network from the available profiles list, click
the button.
Set Default Button To designate a wireless network as the default network for the
connection from the available profiles list, click the button.
Signal Strength This bar shows the signal strength level. The higher percentage
shown in the bar, the more radio signal been received by the
adapter. This indicator helps to find the proper position of the
wireless device for quality network operation.
Signal Quality This bar indicates the quality of the link. The higher the
percentage, the better the quality.

10
Parameter Description
Network Name(SSID) The SSID (up to 32 printable ASCII characters) is the unique
name identified in a WLAN. The ID prevents the unintentional
merging of two co-located WLANs.
Only the wireless devices with the same SSID can interconnect.
Wireless Network Key(WEP) WEP is an authentication algorithm, which protects authorized
Wireless LAN users against eavesdropping. The security setting
must be the the same on the wireless stations within the network.
Data Encryption(WEP
Enabled) To enable the WEP function, select the check box.
Network Authenticaton
(Shared Mode) The wireless network supports two subtypes of network authentication services: Open System and Shared Key. Under
Open System authentication, any wireless stations can request
authentication. Under Shared Key authentication, only wirelss
stations using a shared key (WEP Key) are allowed to
authenticate mutually. This network authentication mode setting
has to be consistent with the wireless network which the adapter
intends to connect.

11
Parameter Description
Wireless Network Key(WEP)
Network Key If the network is required for Wired Equivalent Privacy (WEP) key,
type the key in the text box. The key should be 10 or 26
hexadecimal characters according to the WEP mode designated
by the network.
Note: The hexadecimal characters include the range of “A-F”, “a-
f” and “0-9”, for example: “0123456aef“ or
“01234567890123456789abcdef“.
Confirmed Network Key Enter the same network key again to cofirm the key.
Key Index(Advanced) Select one of the four keys to encrypt your data.
Enable IEEE 802.1x
authentication for this network IEEE 802.1x authentication provides enhanced security for wireless network. If the wireless network requries IEEE 802.1x
authentication for accessing to the network, please select the
check box.
The “EAP-MD5 Authentication“ screen (see the screen above) will
appear when you attempt to conenct the wireless network which
requires for IEEE 802.1x authentication. Please enter the user
name and password which your network administrator assigns to
you.
Note: This adapter only supports EAP-MD5 algorithm of the IEEE
802.1x authentication method when running in Windows
98SE/Me/2000/XP operating systems. Windows XP supports more
algorithm of IEEE 802.1x such as EAP-TLS, please uses the
Windows XP built-in Utility if you need to use the authentication
method other than EAP-MD5.
This is a comupter-to-
computer(ad hoc) network;
wireless access points are not
used
In Computer-to-Comupter mode (Ad Hoc), wireless stations
connect to each other directly, no Access Point is required. If the
wireless network you selected is in Ad Hoc mode, select this
check box.
3.3 Advanced Configuration
This screen allows you to do some advanced configuration including Power Save Mode,
Encryption Algorithm and some specific settings for the adapter.

12
Parameter Description
Ad Hoc Default Channel Select the number of the radio channel used for the Ad Hoc
networking. The channel of all the wireless stations in the Ad Hoc
network should be the same. The parameter is not active in the
infrastructure operation mode.
Note: The Infrastructure operation mode requires the presence of
an 802.11 Access Point. All communication is done via the
Access Point.
Encryption Algorithm The parameter is only active in the Ad Hoc operation mode. There
are three kinds of encrypion algorithm supported by the adapter
including WEP, TKIP and AES.
WEP is an authentication algorithm, which protects authorized
Wireless LAN users against eavesdropping. WEP has been found
that it has some security problems. TKIP is a temporary quick-fix
method defined in IEEE 802.11i standard to quickly overcome the
inherent weaknesses in WEP security. AES has been developed
to ensure the highest degree of security and authenticity for
digital information and it is the most advanced solution defined by
IEEE 802.11i for the security in the wireless network.
The security setting must be the the same on the wireless stations
within the network.

13
Parameter Description
Preamble Mode The preamble defines the length of the CRC block for
communication among the wireless stations. There are three
mode including Long, Short and Auto. High network traffic areas
should use the shorter preamble type. If “Auto“ mode is selected,
the adapter will auto switch the preamble mode depending on the
wireless stations which the adapter is connecting to.
Note that the parameter is only active in the Ad Hoc operation
mode.
Show Icon in System Tray Enable or disable the icon shown in the system tray.
Radio Off When the setting is checked, the wireless connection of the
adapter will be disabled.
Power Save • CAM(Continuous Access Mode) – Adapter will always set in
active mode.
• Max – Enable the adapter in the power saving mode when it is
idle.
• Fast – Enable the adapter in the power saving mode when it
is idle, but some compoents of the adapter is still alive. In this
mode, the power consumption is larger than “Max“ mode.
Rescan Button Click this button to scan the wireless network which the adapter is
connecting to.
3.4 Status
This screen shows the information of manufacturer, driver version, settings of the wireless
network the adapter is connecting to, linking time and link status. If you don’t ensure the
status of the adapter and the network you are connecting, please go to the screen for more
details.

14
3.5 Statistics
You can get the real time information about the packet transmission and receiving status
during wireless communication from the screen. If you want to recount the statistics value,
please click “Reset“ button.

15
3.6 About
This screen displays the version and the designer of the Utility.