Edimax IC-9000 User manual

Copyrightby Edimax Technology Co, LTD. all rights reserved. No part of this
publication may be reproduced, transmitted, transcribed, stored in a retrieval
system, or translated into any language or computer language, in any form or
by any means, electronic, mechanical, magnetic, optical, chemical, manual or
otherwise, without the prior written permission of this Company.
This company makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any
warranties, merchantability or fitness for any particular purpose. Any software
described in this manual is sold or licensed "as is". Should the programs prove
defective following their purchase, the buyer (and not this company, its
distributor, or its dealer) assumes the entire cost of all necessary servicing,
repair, and any incidental or consequential damages resulting from any defect
in the software. Further, this company reserves the right to revise this
publication and to make changes from time to time in the contents hereof
without obligation to notify any person of such revision or changes.
The product you have purchased and the setup screen may appear slightly
different from those shown in this QIG. For more detailed information about
this product, please refer to the User's Manual on the CD-ROM. The software
and specifications could be subjected to change without notice. Please visit
our web site www.edimax.com for the update. All right reserved including all
brand and product names mentioned in this manual are trademarks and/or
registered trademarks of their respective holders.
Notice according to GNU/GPL
-
Version 2
This product includes software that is subject to the GNU/GPL-Version 2.
You find the text of the license on the product cd/dvd. The program is free
software and distributed without any warranty of the author. We offer, valid
for at least three years, to give you, for a charge no more than the costs of
physically performing source distribution, a complete machine-readable
copy of the corresponding source code.
Please contact Edimax at: Edimax Technology co., Ltd, NO. 3, Wu-Chuan
3rd RD Wu-Ku-Industrial Park, Taipei Hsien, Taiwan. R.O.C., TEL :
[phone], FAX : [phone], [e-mail]

1. Product Information
Thank you for purchasing this IC-9000! The IC-9000 is designed
with the “user-friendly” concept. You can install the IP Camera easily
on your home network and then access the IP Camera anywhere in
the world with the video management utility. No need to set
complicated DNS name or change the router’s configuration. It’s
just a plug & play.
Before you start to use the IC-9000, please check the package
contents. If anything is missing, please contact the dealer of
purchase and return the package to claim for missing contents.
2. Check Your Package Contents
 One IC-9000 DDNS-Free Outdoor IP Camera
 One Power Adapter
 One Ethernet Cable
 One Bracket
 One Installation Guide
 One CD ROM (User Guide & Utility)
 One Account Card
 One Accessory Bag (Including Anchors & Screws)
If any of the above items are missing, please contact your
supplier.
3. System Requirement
 CPU: Pentium 4 (or equivalent AMD) 1.0 GHz or above, 1 GB
RAM
 OS: Windows XP/Vista/Win 7
 Browser: IE 7 or above

4. Interface Information
Item
No.
Name Description
1
Ethernet
Indication
LED (blue)
Indicates if the Ethernet link is ok and
packet traffic is sending/receiving. When the
Ethernet cable is connected, the LED is
constant blue light. When there is packet
sending/receiving, the LED is blinking blue
light.
2
Status
Indication
LED (red)
Indicates the Internet connection status.
When the Internet connection is connected,
the LED will be constant red light. If there is
any Internet connection problem, the LED
will be blinking red light.
3 Lens The focus of the lens is fixed. The effective
focus range is from 30cm to infinity.
4 IR LEDs Totally 36 IR LEDs which can provide
approximately 30m distance night vision
5 Light Sensor
The light detector can detect when the light
is becoming dark and turn on the IR LEDs
automatically
6 Ethernet
Jack
10/100Mbps fast Ethernet port (Connects to
your local area network)
7 Digital Input This is for alarm detection, an open circuit is
Status Indication LED
Ethernet Indication LED

Terminal
Block
off, a close circuit is on.
8 Power Jack
Connects to12V/1.0A power adapter.
Please make sure you are using the correct
power adaptor
9 Reset Button
The button to reset the IP CAM to default
factory settings. You need to press the reset
button for more than 4 seconds to enable
the reset function.

5. Hardware Installation
Please follow the following instructions to set up the IC-9000:
1. Please connect the IP CAM accessories to the body of the
IC-9000 correctly, including the bracket, power adapter and
Ethernet cable, as shown in the above figure.
2. Connect the other end of the Ethernet cable to the home
network or office network. Usually, this Ethernet cable is plugged
into a home NAT/router device or an Ethernet switch if in the
office, as shown in the above figure.
3. Since the default settings of the IP CAM use DHCP function and
very often there is a DHCP server on most of the Home/office
network, the IP CAM should be connected to the Internet
immediately

6. Software Installation
1. Before installing CamView software on your PC or laptop, please
make sure you have correctly installed the IC-9000. It’s highly
recommended to close other Windows applications to prevent
the installation from any possbile confliction.
2. Please insert the installation CD into the CD-ROM drive in your
notebook or personal computer (must be running Microsoft
Windows OS)
3. Execute the program CamView on the disk. The program will
pop-up some windows about the installation options, please
press the “Next” button to proceed with the installation.
4. After the installation is complete, there will be a CamView icon
on the desktop of your computer screen, please execute this
icon. The CamView program will run immediately.

7. Start to Use CamView Software
1. Start the CamView application from either Start -> Programs ->
CamView or the shortcut on the desktop of the Microsoft
Windows.
2. Once the CamView Started, it will search the IC-9000 in your
Local Area Network automatically and show the CAM ID of each
of the found IP Cam in the tree menu –“Auto Search” folder of
the Cam List page.
Note: To save the found Cam ID on your PC, simply drag it from
“Auto Search” folder to “CameraList”. By doing so, you can
easily play the video without memorizing the Cam ID
3. To View the video, simply double click on the CAM ID which you
want to see or drag the CAM ID to one of the video play
windows.

Note: If the Camera you want to see is outside of your LAN and
the Cam ID is not sored in the “CameraList”, please right-click on
the “CameraList”, choose “New Camera” and enter the Cam ID
and password.
Note: For further operation, please refer to the manual.

R&TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE 1999/5/EC
OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of March 9, 1999
on radio equipment and telecommunication terminal Equipment and the
mutual recognition of their conformity (R&TTE)
The R&TTE Directive repeals and replaces in the directive 98/13/EEC
(Telecommunications Terminal Equipment and Satellite Earth Station
Equipment) As of April 8, 2000.
Safety
This equipment is designed with the utmost care for the safety of those who
install and use it. However, special attention must be paid to the dangers of
electric shock and static electricity when working with electrical equipment. All
guidelines of this and of the computer manufacture must therefore be allowed
at all times to ensure the safe use of the equipment.
EU Countries Intended for Use
The ETSI version of this device is intended for home and office use in Austria,
Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy,
Luxembourg, Bulgaria, Cyprus, Czech Republic, Estonia, Hungary, Latvia,
Lithuania, Malta, Poland, Romania, Slovakia, Slovenia, the Netherlands,
Portugal, Spain, Sweden, and the United Kingdom.
The ETSI version of this device is also authorized for use in EFTA member
states: Iceland, Liechtenstein, Norway, and Switzerland.
EU Countries not intended for use
None
EuP, 2005/32/EC.
Article15,5,(a): there shall be no significant negative impact on the
functionality of the product, from the perspective of the user