Edirol DV-7DLC User manual

Owner’s Manual
Congratulations on your purchase of the remote controller DV-7DLC.
This is the remote controller you can use with the DV-7DL series (DV-7DL/
DV-7DL PRO etc.) and PR-50.
USING THE UNIT SAFELY ............................................ p. 2
IMPORTANT NOTES...................................................... p. 3
Connecting the DV-7DLC.............................................. p. 4
Part Names and Functions ........................................... p. 5
Contents
Copyright © 2004 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form
without the written permission of ROLAND CORPORATION.
Before using this unit, carefully read the sections entitled: “USING THE UNIT
SAFELY” and “IMPORTANT NOTES” (p. 2; p. 3). These sections provide
important information concerning the proper operation of the unit. Additionally,
in order to feel assured that you have gained a good grasp of every feature
provided by your new unit, Owner’s Manual should be read in its entirety. The
manual should be saved and kept on hand as a convenient reference.
DV-7DLC_e.book 1 ページ ２００４年６月２５日 金曜日 午前９時２９分

2
USING THE UNIT SAFELY
001
• Before using this unit, make sure to read the instruc-
tions below, and the Owner’s Manual.
..........................................................................................................
002a
• Do not open or perform any internal modifications
on the unit.
..........................................................................................................
003
• Do not attempt to repair the unit, or replace parts
within it (except when this manual provides specific
instructions directing you to do so). Refer all
servicing to your retailer, the nearest Roland Service
Center, or an authorized Roland distributor, as listed
on the “Information” page.
..........................................................................................................
004
• Never use or store the unit in places that are:
• Subject to temperature extremes (e.g., direct
sunlight in an enclosed vehicle, near a heating
duct, on top of heat-generating equipment); or
are
• Damp (e.g., baths, washrooms, on wet floors);
or are
• Humid; or are
• Exposed to rain; or are
• Dusty; or are
• Subject to high levels of vibration.
..........................................................................................................
007
• Make sure you always have the unit placed so it is
level and sure to remain stable. Never place it on
stands that could wobble, or on inclined surfaces.
..........................................................................................................
011
• Do not allow any objects (e.g., flammable material,
coins, pins); or liquids of any kind (water, soft drinks,
etc.) to penetrate the unit.
..........................................................................................................
012d
• Immediately turn the power off, and request
servicing by your retailer, the nearest Roland Service
Center, or an authorized Roland distributor, as listed
on the “Information” page when:
• If smoke or unusual odor occurs
• Objects have fallen into, or liquid has been
spilled onto the unit; or
• The unit has been exposed to rain (or otherwise
has become wet); or
•The unit does not appear to operate normally or
exhibits a marked change in performance.
..........................................................................................................
013
• In households with small children, an adult should
provide supervision until the child is capable of
following all the rules essential for the safe operation
of the unit.
..........................................................................................................
014
• Protect the unit from strong impact.
(Do not drop it!)
..........................................................................................................
104
• Try to prevent cords and cables from becoming
entangled. Also, all cords and cables should be
placed so they are out of the reach of children.
..........................................................................................................
106
•Never climb on top of, nor place heavy objects on the
unit.
..........................................................................................................
108c
• Disconnect all cords coming from external devices
before moving the unit.
..........................................................................................................
Used for instructions intended to alert
the user to the risk of injury or material
damage should the unit be used
improperly.
* Material damage refers to damage or
other adverse effects caused with
respect to the home and all its
furnishings, as well to domestic
animals or pets.
Used for instructions intended to alert
the user to the risk of death or severe
injury should the unit be used
improperly.
The ●symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In
the case of the symbol at left, it means that the power-
cord plug must be unplugged from the outlet.
The symbol alerts the user to important instructions
or warnings.The specific meaning of the symbol is
determined by the design contained within the
triangle. In the case of the symbol at left, it is used for
general cautions, warnings, or alerts to danger.
The symbol alerts the user to items that must never
be carried out (are forbidden). The specific thing that
must not be done is indicated by the design contained
within the circle. In the case of the symbol at left, it
means that the unit must never be disassembled.
DV-7DLC_e.book 2 ページ ２００４年６月２５日 金曜日 午前９時２９分

3
IMPORTANT NOTES
In addition to the items listed under “USING THE UNIT SAFELY” on page 2, please read and observe the following:
Power Supply
307
• Before connecting this unit to other devices, turn off the
power to all units. This will help prevent malfunctions and/
or damage to speakers or other devices.
Placement
352a
•This device may interfere with radio and television reception.
Do not use this device in the vicinity of such receivers.
352b
• This unit may not work correctly if wireless communications
devices, such as cell phones, are operated in the vincity of this
unit. Such error could occur when receiving or initiating a
call, or while conversing. Should you experience such
problems, you should relocate such wireless devices so they
are at a greater distance from this unit, or switch them off.
354a
•Do not expose the unit to direct sunlight, place it near devices
that radiate heat, leave it inside an enclosed vehicle, or
otherwise subject it to temperature extremes. Excessive heat
can deform or discolor the unit.
355b
• When moved from one location to another where the temper-
ature and/or humidity is very different, water droplets
(condensation) may form inside the unit. Damage or
malfunction may result if you attempt to use the unit in this
condition. Therefore, before using the unit, you must allow it
to stand for several hours, until the condensation has
completely evaporated.
Maintenance
401a
• For everyday cleaning wipe the unit with a soft, dry cloth or
one that has been slightly dampened with water. To remove
stubborn dirt, use a cloth impregnated with a mild, non-
abrasive detergent. Afterwards, be sure to wipe the unit
thoroughly with a soft, dry cloth.
402
• Never use benzine, thinners, alcohol or solvents of any kind,
to avoid the possibility of discoloration and/or deformation.
Additional Precautions
553
• Use a reasonable amount of care when using the unit’s
buttons, sliders, or other controls; and when using its jacks
and connectors. Rough handling can lead to malfunctions.
556
• When connecting / disconnecting all cables, grasp the
connector itself—never pull on the cable. This way you will
avoid causing shorts, or damage to the cable’s internal
elements.
558a
• To avoid disturbing your neighbors, try to keep the unit’s
volume at reasonable levels. You may prefer to use
headphones, so you do not need to be concerned about those
around you (especially when it is late at night).
559a
• When you need to transport the unit, package it in the box
(including padding) that it came in, if possible. Otherwise,
you will need to use equivalent packaging materials.
..................................................................................................................................................................................................................................
This product complies with the requirements of European Directive 89/336/EEC.
For EU Countries
For Canada
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
NOTICE
AVIS
For the USA
FEDERAL COMMUNICATIONS COMMISSION
RADIO FREQUENCY INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Unauthorized changes or modification to this system can void the users authority to operate this equipment.
This equipment requires shielded interface cables in order to meet FCC class B Limit.
For the USA
DECLARATION OF CONFORMITY
Compliance Information Statement
Model Name :
Type of Equipment :
Responsible Party :
Address :
Telephone :
DV-7DLC
VIDEO EDITING CONTROLLER
Edirol Corporation North America
425 Sequoia Drive, Suite 114, Bellingham, WA 98226 U. S. A.
[phone]
DV-7DLC_e.book 3 ページ ２００４年６月２５日 金曜日 午前９時２９分

4
Connecting the DV-7DLC
• Use the cable packed with the unit to make the connection.
• Never try to connect two or more DV-7DLC units to one another.
• To prevent malfunction and/or damage to speakers or other devices, always turn down the volume,
and turn off the power on all devices before making any connections.
1. Switch off the power to the DV-7DL.
Make sure that all indicator lights on the front panel of the DV-7DL unit are dark.
2. Connect the cable to the rear or front panel of the DV-7DL series or PR-50 unit.
● Two USB connectors are equipped on the rear panel of DV-7DL series/PR-50. Check the shape of the
connector on the included cable, and connect the flat one to either one of the USB connectors.
● Two USB connectors are equipped on the front panel of DV-7DL series/PR-50. Check the shape of the
connector on the included cable, and connect the flat one to either one of the USB connectors.
* Orient the connector so that the side with the symbol faces up, and insert it firmly, as far as it will go.
3. Connect the cable to the DV-7DLC.
Connect the end of the included cable with the small connector to the REMOTE jack on the DV-7DLC.
* Orient the connector so that the side with the symbol faces up, and insert it firmly, as far as it will go.
flat connector
(Included cable)
Connect with the USB connector on the
rear panel (Connection Example: DV-7DL)
USB connector
(upper or lower)
Connect with the USB connector on the
front panel (Connection Example: DV-7DL)
flat connector
(Included cable)
USB connector
(upper or lower)
REMOTE jack
DV-7DLC
small connector
(Included cable)
DV-7DLC rear panel
DV-7DLC_e.book 4 ページ ２００４年６月２５日 金曜日 午前９時２９分

5
Part Names and Functions
When you’re using the DV-7DLC as a controller for the PR-50, the buttons, sliders, and other controls on the
DV-7DLC work differently than their functions indicated by the panel labels. For more information, refer to the
Owner’s Manual included with the PR-50.
* The PR-50 comes with template stickers for the DV-7DLC.
Fader Selector Button
Use the fader selector button the target of operation
for audio fader 4. You can determine the current
target of operation by checking whether the button
light is on or off.
• When the button is lit
The control adjusts the master volume level.
• When the button is unlit
The control adjusts the volume level of Audio
track 4.
MUTE Buttons (1–4)
Mute buttons 1 through 4 correspond respectively
to Audio Tracks 1 through 4. Pressing a button to
make it light up mutes out the audio on the
corresponding Audio track. Pressing the button a
second time to make it go dark makes the sound
audible again.
Audio Faders (1–4)
You can control the faders volume level for the
Audio tracks. When the Fader Selector button is
lighted up, audio fader 4 adjusts the master volume
level.
T-bar
You can zoom in/out the Timeline Palette, to make
the video fade to a black or white screen, and for
other operations.
* The action of the T-bar depends on whether the Mode
Selector button ( , on Page 6) is lighted or dark.
Left Side of the DV-7DLC
2
3
Left Side of the DV-7DLC
MUTE Buttons (1–4)
Audio Faders (1–4)
1Fader Selector Button 4T-bar
1
2
3
1
4
5
DV-7DLC_e.book 5 ページ ２００４年６月２５日 金曜日 午前９時２９分

6
Part Names and Functions
T-bar Mode Selector Button
You to select the T-bar mode.
• When the button is lit
You can control the function assigned by “DV-7DLC T-Bar Control” under the Settings menu for the
DV-7DL/DV-7DL PRO.
• When the button is unlit
When the A/B Roll feature is active (“on”), this switches the two Video tracks.
Pull the T-bar back to output the video on the Main Video track, and push it forward to output the
video on the Insert Video track.
* The DV-7DL is not provided with the A/B Roll feature.
5
“DV-7DLC T-Bar Control”
setting item Functions assigned to the T-bar
OFF
No function assigned to the T-bar.
Timeline zoom
Pull the T-bar back to zoom in and push forward to zoom out.
White fade
When the editing screen is displayed, you can control the video fade
toward white.
Pull the T-bar back to output the video unchanged and push it forward
to output video that turns white.
Black fade
When the editing screen is displayed, you can control the video fade
toward black.
Pull the T-bar back to output the video unchanged and push it forward
to output video that turns black.
Right Side of the DV-7DLC
5 6
9
8
7
Set IN Point/OUT Point
Buttons
REC Button
A/B ROLL Button PUNCH IN/OUT Button
MARKER Setting Button
DELETE Marker Button
Jog/Shuttle Dial
MAKER
JUMP Buttons
Play Control Buttons
T-bar Mode
Selector Button
DV-7DLC_e.book 6 ページ ２００４年６月２５日 金曜日 午前９時２９分

7
Part Names and Functions
A/B ROLL Button
The A/B ROLL button switches the A/B Roll
feature on and off.
* The DV-7DL is not provided with the A/B Roll feature.
PUNCH IN/OUT Button
The PUNCH IN/OUT button is the same operation
as (the Punch Recording button) on the
editing screen of DV-7DL series devices.
During playback of a sequence, it places titles and
audio material at the timing you choose.
Set IN Point/Set OUT Point Buttons
You can use these to set IN points and OUT points
on the Timeline Palette or in material, and perform
playback of the passage between the points.
REC Button
The REC button is the same operation as
(the REC button) in the Recording window on
DV-7DL series devices.
You use it to start and end recording on Audio
tracks.
Play Control Buttons
You can use these to perform operations such as
indexing or fast-forwarding a sequence or piece of
material.
MARKER Setting Button
You can create a marker at the location of the
position bar.
DELETE Marker Button
You can delete a marker at the location of the
position bar.
MARKER JUMP Buttons
You can use these to make the position bar jump to
the location of an earlier or later marker.
Jog/Shuttle Dial
You can use these to perform operations such as
indexing or fast-forwarding a sequence or piece of
material.
• Jog Dial
(Black Center Dial)
You can use this to move the position bar one frame
at a time.
Turning the dial clockwise moves the position bar
to the following frame, and turning it
counterclockwise moves the position bar to the
previous frame.
* Playback stops as soon as operation finishes.
• Shuttle Dial
(Gray Outer Dial)
You can perform slow playback, normal-speed
playback, and fast forwarding by turning this
clockwise.
The operation performed depends on the degree to
which you turn the dial. You can perform slow
reverse playback, normal-speed reverse playback,
and rewinding by turning this counterclockwise.
* Playback stops as soon as operation finishes.
6
7
8
Sets an In point
Plays back the passage from the
In point to the Out point.
Sets an In point.
9
Stops playback. Playbacks.
Advances one
frame.
Moves back one frame.
Moves to the final frame.Moves to the top frame.
Rewinds ten frames.
Advances ten frames.
Moves to the
next marker.
Moves to the
previous marker.
Moves to the
previous frame.
Moves to the
next frame.
Slow reverse
playback Slow playback
Rewind Fast forward
DV-7DLC_e.book 7 ページ ２００４年６月２５日 金曜日 午前９時２９分

03670445 ’04-7-1KS
This owner’s manual is printed on recycled paper.
Information
When you need repair service, call your nearest EDIROL/Roland Service Center or authorized EDIROL/Roland distributor
in your country as shown below.
As of May 1, 2004 (EDIROL-2)
ASIA
TAIWAN
ROLAND TAIWAN
ENTERPRISE CO., LTD.
Room 5, 9fl. No. 112 Chung Shan
N.Road Sec.2, Taipei, TAIWAN,
R.O.C.
TEL: [phone]
BRAZIL
Roland Brasil Ltda
Rua San Jose, 780 Sala B
Parque Industrial San Jose
Cotia - Sao Paulo - SP, BRAZIL
TEL: [phone]
CENTRAL/LATIN
AMERICA DENMARK
Roland Scandinavia A/S
Nordhavnsvej 7, Postbox 880,
DK-2100 Copenhagen
DENMARK
TEL: [phone]
FRANCE
Roland France SA
4, Rue Paul Henri SPAAK,
Parc de l'Esplanade, F 77 462 St.
Thibault, Lagny Cedex FRANCE
TEL: [phone]
FINLAND
Roland Scandinavia As,
Filial Finland
Elannontie 5
FIN-01510 Vantaa, FINLAND
TEL: [phone]
GERMANY
Roland Elektronische
Musikinstrumente HmbH.
Oststrasse 96, 22844 Norderstedt,
GERMANY
TEL: [phone]
AUSTRIA
Roland Elektronische
Musikinstrumente HmbH.
Austrian Office
Eduard-Bodem-Gasse 8,
A-6020 Innsbruck, AUSTRIA
TEL: [phone]
BELGIUM/HOLLAND/
LUXEMBOURG
Roland Benelux N. V.
Houtstraat 3, B-2260, Oevel
(Westerlo) BELGIUM
TEL: [phone]
EUROPE
HUNGARY
Roland East Europe Ltd.
Warehouse Area ‘DEPO’ Pf.83
H-2046 Torokbalint, HUNGARY
TEL: [phone]
ITALY
Roland Italy S. p. A.
Viale delle Industrie 8,
20020 Arese, Milano, ITALY
TEL: [phone]
NORWAY
Roland Scandinavia Avd.
Kontor Norge
Lilleakerveien 2 Postboks 95
Lilleaker N-0216 Oslo
NORWAY
TEL: [phone]
PORTUGAL
Tecnologias Musica e Audio,
Roland Portugal, S.A.
Cais Das Pedras, 8/9-1 Dto
4050-465 PORTO
PORTUGAL
TEL: [phone]
POLAND
MX MUSIC SP.Z.O.O.
UL. Gibraltarska 4.
PL-03664 Warszawa POLAND
TEL: [phone]
GREECE
STOLLAS S.A.
Music Sound Light
155, New National Road
Patras 26442, GREECE
TEL: [phone]
RUSSIA
MuTek
3-Bogatyrskaya Str. 1.k.l
107 564 Moscow, RUSSIA
TEL: [phone]
SPAIN
Roland Electronics
de España, S. A.
Calle Bolivia 239, 08020
Barcelona, SPAIN
TEL: [phone]
SWITZERLAND
Roland (Switzerland) AG
Landstrasse 5, Postfach,
CH-4452 Itingen,
SWITZERLAND
TEL: [phone]
SWEDEN
Roland Scandinavia A/S
SWEDISH SALES OFFICE
Danvik Center 28, 2 tr.
S-131 30 Nacka SWEDEN
TEL: [phone]
UKRAINE
TIC-TAC
Mira Str. 19/108
P.O. Box 180
295400 Munkachevo, UKRAINE
TEL: [phone]
UNITED KINGDOM
Roland (U.K.) Ltd.
Atlantic Close, Swansea
Enterprise Park, SWANSEA
SA7 9FJ,
UNITED KINGDOM
TEL: [phone]
ROMANIA
FBS LINES
Piata Libertatii 1,
535500 Gheorgheni, ROMANIA
TEL: [phone]
U. S. A. / CANADA
EDIROL Corporation North
America
425 Sequoia Drive, Suite 114
Bellingham, WA 98226
U. S. A.
TEL: [phone]
FAX: [phone]
http://www.edirol.com/
EUROPE
EDIROL (Europe) Ltd.
Studio 3.4 114 Power Road
London W4 5PY
U. K.
TEL: [phone]
FAX:[phone]
http://www.edirol.com/europe
Deutschland
TEL: [phone]
France
TEL: [phone]
Italia
TEL: [phone]
AUSTRALIA
Roland Corporation
Australia Pty., Ltd.
38 Campbell Avenue
Dee Why West. NSW 2099
AUSTRALIA
TEL: [phone]
AUSTRALIA
IRELAND
Roland Ireland
G2 Calmount Park, Calmount
Avenue, Dublin 12
Republic of IRELAND
TEL: [phone]
CZECH REP.
K-AUDIO
Kardasovska 626.
CZ-198 00 Praha 9,
CZECH REP.
TEL: [phone]
*In the interest of product improvement, the specifications and/or appearance of this unit are subject
to change without prior notice.
Specification
DV-7DLC: Video Editing Controller for DV-7DL series/PR-50
Power Supply Supplied from USB connector on DV-7DL series/PR-50
Dimensions
338 (W) x 205 (D) x 98 (H)
13-5/16 (W) x 8-1/8 (D) x 3-7/8 (H) inches mm
Weights
1.2 kg
2 lbs 11 oz
Accessories Connector cable, Owner’s Manual
DV-7DLC_e.book 8 ページ ２００４年６月２５日 金曜日 午前９時２９分