EDM 33800 User manual

4
/ Do not use the lamp without the glass. If it is
damaged, it must be replaced with a new one
The lamp is designed to use only self-protected tungsten
halogen light bulbs.
Exclusive use in enclosed spaces.
IP Level of protection against intrusion. You can find the
corresponding protection level on the label of the lamp.
The luminaire can under no circumstances be mounted
on normally flammable surfaces.
Switching it on
Connect to the power supply and check the functioning of
the fan. A series of pulses controls the speed of the fan, as
follows:
Press once - fast; press 2 times - medium speed; press 3
times - slow; press 4 times - off. The speed adjustments to
increase or reduce the temperature will depend on factors
such as the size of the room, its height, the number of fans
available, etc. Using the sliding switch, you can control the
direction of the fan, forward or backward.
Hot temperatures/low position - (forward) The fan turns
anti-clockwise. The downward air current creates a cooling
effect, as shown in figure A.
This enables you to set the air conditioning to a higher
temperature without compromising on comfort.
Low temperatures/upper position - (backward) The fan turns
clockwise. The upward air current causes the warm air in the
upper part of the room to move to other areas, as shown in
figure B.
This enables you to set the heating to a lower temperature
without compromising on comfort.
(Before using your fan in this position, consult point 10 of
the safety instructions).
NOTE: Switch the fan off and wait until it has stopped
completely before changing the position of the sliding
switch forward or backward.
Maintenance
1. Due to the normal movement of the fan, it is possible that
some connections may come lose. Check the support
connections, the supports and the attachment of the blades
twice a year. Make sure they are securely attached.

3
15. This appliance can be used by children aged 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowladge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by
children without supervisions.
16. The means for disconnection from the supply mains
having a contact separation in all poles that provides full
disconnection that must be incorporated in the fixed wiring
in accordance with the wiring rules.
17. Regarding the instructions for the method of fixing and
how to install the fan, thanks to refer to the section
“INSTALLATION”.
18. Regarding the method of the cable connection, thanks to
refer to the section "CABLE INFORMATION".
Description of symbols:
You will find all the symbols related to his lamp on both the
product label and the box in which it came.
Insulation class I . This fan must be connected with its
ground wire (green and yellow cable) to the earthing
conductor.
Insulation class II . This fan has double insulation and it
must not be connected to the earth connection.
AC - Alternating Current Voltage
Frequency (hertz)
Voltage in volts
Intensity of current in watts
Exclusive use in enclosed spaces.
IP Level of protection against intrusion. You can find the
corresponding protection level on the label of the lamp.
The luminaire can under no circumstances be mounted
on normally flammable surfaces.
Switching it on
Connect to the power supply and check the functioning of
the fan. A series of pulses controls the speed of the fan, as
follows:
Press once - fast; press 2 times - medium speed; press 3
times - slow; press 4 times - off. The speed adjustments to
increase or reduce the temperature will depend on factors
4
/ Do not use the lamp without the glass. If it is
damaged, it must be replaced with a new one
The lamp is designed to use only self-protected tungsten
halogen light bulbs.
Exclusive use in enclosed spaces.
IP Level of protection against intrusion. You can find the
corresponding protection level on the label of the lamp.
The luminaire can under no circumstances be mounted
on normally flammable surfaces.
Switching it on
Connect to the power supply and check the functioning of
the fan. A series of pulses controls the speed of the fan, as
follows:
Press once - fast; press 2 times - medium speed; press 3
times - slow; press 4 times - off. The speed adjustments to
increase or reduce the temperature will depend on factors
such as the size of the room, its height, the number of fans
available, etc. Using the sliding switch, you can control the
direction of the fan, forward or backward.
Hot temperatures/low position - (forward) The fan turns
anti-clockwise. The downward air current creates a cooling
effect, as shown in figure A.
This enables you to set the air conditioning to a higher
temperature without compromising on comfort.
Low temperatures/upper position - (backward) The fan turns
clockwise. The upward air current causes the warm air in the
upper part of the room to move to other areas, as shown in
figure B.
This enables you to set the heating to a lower temperature
without compromising on comfort.
(Before using your fan in this position, consult point 10 of
the safety instructions).
NOTE: Switch the fan off and wait until it has stopped
completely before changing the position of the sliding
switch forward or backward.
Maintenance
1. Due to the normal movement of the fan, it is possible that
some connections may come lose. Check the support
connections, the supports and the attachment of the blades
twice a year. Make sure they are securely attached.
4
/ Do not use the lamp without the glass. If it is
damaged, it must be replaced with a new one
The lamp is designed to use only self-protected tungsten
halogen light bulbs.
Exclusive use in enclosed spaces.
IP Level of protection against intrusion. You can find the
corresponding protection level on the label of the lamp.
The luminaire can under no circumstances be mounted
on normally flammable surfaces.
Switching it on
Connect to the power supply and check the functioning of
the fan. A series of pulses controls the speed of the fan, as
follows:
Press once - fast; press 2 times - medium speed; press 3
times - slow; press 4 times - off. The speed adjustments to
increase or reduce the temperature will depend on factors
such as the size of the room, its height, the number of fans
available, etc. Using the sliding switch, you can control the
direction of the fan, forward or backward.
Hot temperatures/low position - (forward) The fan turns
anti-clockwise. The downward air current creates a cooling
effect, as shown in figure A.
This enables you to set the air conditioning to a higher
temperature without compromising on comfort.
Low temperatures/upper position - (backward) The fan turns
clockwise. The upward air current causes the warm air in the
upper part of the room to move to other areas, as shown in
figure B.
This enables you to set the heating to a lower temperature
without compromising on comfort.
(Before using your fan in this position, consult point 10 of
the safety instructions).
NOTE: Switch the fan off and wait until it has stopped
completely before changing the position of the sliding
switch forward or backward.
Maintenance
1. Due to the normal movement of the fan, it is possible that
some connections may come lose. Check the support
connections, the supports and the attachment of the blades
twice a year. Make sure they are securely attached.
4
/ Do not use the lamp without the glass. If it is
damaged, it must be replaced with a new one
The lamp is designed to use only self-protected tungsten
halogen light bulbs.
Exclusive use in enclosed spaces.
IP Level of protection against intrusion. You can find the
corresponding protection level on the label of the lamp.
The luminaire can under no circumstances be mounted
on normally flammable surfaces.
Switching it on
Connect to the power supply and check the functioning of
the fan. A series of pulses controls the speed of the fan, as
follows:
Press once - fast; press 2 times - medium speed; press 3
times - slow; press 4 times - off. The speed adjustments to
increase or reduce the temperature will depend on factors
such as the size of the room, its height, the number of fans
available, etc. Using the sliding switch, you can control the
direction of the fan, forward or backward.
Hot temperatures/low position - (forward) The fan turns
anti-clockwise. The downward air current creates a cooling
effect, as shown in figure A.
This enables you to set the air conditioning to a higher
temperature without compromising on comfort.
Low temperatures/upper position - (backward) The fan turns
clockwise. The upward air current causes the warm air in the
upper part of the room to move to other areas, as shown in
figure B.
This enables you to set the heating to a lower temperature
without compromising on comfort.
(Before using your fan in this position, consult point 10 of
the safety instructions).
NOTE: Switch the fan off and wait until it has stopped
completely before changing the position of the sliding
switch forward or backward.
Maintenance
1. Due to the normal movement of the fan, it is possible that
some connections may come lose. Check the support
connections, the supports and the attachment of the blades
twice a year. Make sure they are securely attached.

Símbolo Función
Hacia arriba en invierno hace circular el aire caliente
por la habitación.
Hacia abajo en verano crea un movimiento de aire
desde el techo.
El interruptor ubicado en la carcasa del motor que
controla la dirección de giro de las aspas, controla
la dirección del movimiento del aire. Precaución:
Antes de usar el interruptor de dirección de giro,
apague el ventilador y asegúrese de que ha dejado
de girar por completo para evitar sufrir lesiones físicas
o dañar el motor.

4
/ Do not use the lamp without the glass. If it is
damaged, it must be replaced with a new one
The lamp is designed to use only self-protected tungsten
halogen light bulbs.
Exclusive use in enclosed spaces.
IP Level of protection against intrusion. You can find the
corresponding protection level on the label of the lamp.
The luminaire can under no circumstances be mounted
on normally flammable surfaces.
Switching it on
Connect to the power supply and check the functioning of
the fan. A series of pulses controls the speed of the fan, as
follows:
Press once - fast; press 2 times - medium speed; press 3
times - slow; press 4 times - off. The speed adjustments to
increase or reduce the temperature will depend on factors
such as the size of the room, its height, the number of fans
available, etc. Using the sliding switch, you can control the
direction of the fan, forward or backward.
Hot temperatures/low position - (forward) The fan turns
anti-clockwise. The downward air current creates a cooling
effect, as shown in figure A.
This enables you to set the air conditioning to a higher
temperature without compromising on comfort.
Low temperatures/upper position - (backward) The fan turns
clockwise. The upward air current causes the warm air in the
upper part of the room to move to other areas, as shown in
figure B.
This enables you to set the heating to a lower temperature
without compromising on comfort.
(Before using your fan in this position, consult point 10 of
the safety instructions).
NOTE: Switch the fan off and wait until it has stopped
completely before changing the position of the sliding
switch forward or backward.
Maintenance
1. Due to the normal movement of the fan, it is possible that
some connections may come lose. Check the support
connections, the supports and the attachment of the blades
twice a year. Make sure they are securely attached.
4
/ Do not use the lamp without the glass. If it is
damaged, it must be replaced with a new one
The lamp is designed to use only self-protected tungsten
halogen light bulbs.
Exclusive use in enclosed spaces.
IP Level of protection against intrusion. You can find the
corresponding protection level on the label of the lamp.
The luminaire can under no circumstances be mounted
on normally flammable surfaces.
Switching it on
Connect to the power supply and check the functioning of
the fan. A series of pulses controls the speed of the fan, as
follows:
Press once - fast; press 2 times - medium speed; press 3
times - slow; press 4 times - off. The speed adjustments to
increase or reduce the temperature will depend on factors
such as the size of the room, its height, the number of fans
available, etc. Using the sliding switch, you can control the
direction of the fan, forward or backward.
Hot temperatures/low position - (forward) The fan turns
anti-clockwise. The downward air current creates a cooling
effect, as shown in figure A.
This enables you to set the air conditioning to a higher
temperature without compromising on comfort.
Low temperatures/upper position - (backward) The fan turns
clockwise. The upward air current causes the warm air in the
upper part of the room to move to other areas, as shown in
figure B.
This enables you to set the heating to a lower temperature
without compromising on comfort.
(Before using your fan in this position, consult point 10 of
the safety instructions).
NOTE: Switch the fan off and wait until it has stopped
completely before changing the position of the sliding
switch forward or backward.
Maintenance
1. Due to the normal movement of the fan, it is possible that
some connections may come lose. Check the support
connections, the supports and the attachment of the blades
twice a year. Make sure they are securely attached.

4
/ Do not use the lamp without the glass. If it is
damaged, it must be replaced with a new one
The lamp is designed to use only self-protected tungsten
halogen light bulbs.
Exclusive use in enclosed spaces.
IP Level of protection against intrusion. You can find the
corresponding protection level on the label of the lamp.
The luminaire can under no circumstances be mounted
on normally flammable surfaces.
Switching it on
Connect to the power supply and check the functioning of
the fan. A series of pulses controls the speed of the fan, as
follows:
Press once - fast; press 2 times - medium speed; press 3
times - slow; press 4 times - off. The speed adjustments to
increase or reduce the temperature will depend on factors
such as the size of the room, its height, the number of fans
available, etc. Using the sliding switch, you can control the
direction of the fan, forward or backward.
Hot temperatures/low position - (forward) The fan turns
anti-clockwise. The downward air current creates a cooling
effect, as shown in figure A.
This enables you to set the air conditioning to a higher
temperature without compromising on comfort.
Low temperatures/upper position - (backward) The fan turns
clockwise. The upward air current causes the warm air in the
upper part of the room to move to other areas, as shown in
figure B.
This enables you to set the heating to a lower temperature
without compromising on comfort.
(Before using your fan in this position, consult point 10 of
the safety instructions).
NOTE: Switch the fan off and wait until it has stopped
completely before changing the position of the sliding
switch forward or backward.
Maintenance
1. Due to the normal movement of the fan, it is possible that
some connections may come lose. Check the support
connections, the supports and the attachment of the blades
twice a year. Make sure they are securely attached.
4
/ Do not use the lamp without the glass. If it is
damaged, it must be replaced with a new one
The lamp is designed to use only self-protected tungsten
halogen light bulbs.
Exclusive use in enclosed spaces.
IP Level of protection against intrusion. You can find the
corresponding protection level on the label of the lamp.
The luminaire can under no circumstances be mounted
on normally flammable surfaces.
Switching it on
Connect to the power supply and check the functioning of
the fan. A series of pulses controls the speed of the fan, as
follows:
Press once - fast; press 2 times - medium speed; press 3
times - slow; press 4 times - off. The speed adjustments to
increase or reduce the temperature will depend on factors
such as the size of the room, its height, the number of fans
available, etc. Using the sliding switch, you can control the
direction of the fan, forward or backward.
Hot temperatures/low position - (forward) The fan turns
anti-clockwise. The downward air current creates a cooling
effect, as shown in figure A.
This enables you to set the air conditioning to a higher
temperature without compromising on comfort.
Low temperatures/upper position - (backward) The fan turns
clockwise. The upward air current causes the warm air in the
upper part of the room to move to other areas, as shown in
figure B.
This enables you to set the heating to a lower temperature
without compromising on comfort.
(Before using your fan in this position, consult point 10 of
the safety instructions).
NOTE: Switch the fan off and wait until it has stopped
completely before changing the position of the sliding
switch forward or backward.
Maintenance
1. Due to the normal movement of the fan, it is possible that
some connections may come lose. Check the support
connections, the supports and the attachment of the blades
twice a year. Make sure they are securely attached.
4
/ Do not use the lamp without the glass. If it is
damaged, it must be replaced with a new one
The lamp is designed to use only self-protected tungsten
halogen light bulbs.
Exclusive use in enclosed spaces.
IP Level of protection against intrusion. You can find the
corresponding protection level on the label of the lamp.
The luminaire can under no circumstances be mounted
on normally flammable surfaces.
Switching it on
Connect to the power supply and check the functioning of
the fan. A series of pulses controls the speed of the fan, as
follows:
Press once - fast; press 2 times - medium speed; press 3
times - slow; press 4 times - off. The speed adjustments to
increase or reduce the temperature will depend on factors
such as the size of the room, its height, the number of fans
available, etc. Using the sliding switch, you can control the
direction of the fan, forward or backward.
Hot temperatures/low position - (forward) The fan turns
anti-clockwise. The downward air current creates a cooling
effect, as shown in figure A.
This enables you to set the air conditioning to a higher
temperature without compromising on comfort.
Low temperatures/upper position - (backward) The fan turns
clockwise. The upward air current causes the warm air in the
upper part of the room to move to other areas, as shown in
figure B.
This enables you to set the heating to a lower temperature
without compromising on comfort.
(Before using your fan in this position, consult point 10 of
the safety instructions).
NOTE: Switch the fan off and wait until it has stopped
completely before changing the position of the sliding
switch forward or backward.
Maintenance
1. Due to the normal movement of the fan, it is possible that
some connections may come lose. Check the support
connections, the supports and the attachment of the blades
twice a year. Make sure they are securely attached.
3
15. This appliance can be used by children aged 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowladge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by
children without supervisions.
16. The means for disconnection from the supply mains
having a contact separation in all poles that provides full
disconnection that must be incorporated in the fixed wiring
in accordance with the wiring rules.
17. Regarding the instructions for the method of fixing and
how to install the fan, thanks to refer to the section
“INSTALLATION”.
18. Regarding the method of the cable connection, thanks to
refer to the section "CABLE INFORMATION".
Description of symbols:
You will find all the symbols related to his lamp on both the
product label and the box in which it came.
Insulation class I . This fan must be connected with its
ground wire (green and yellow cable) to the earthing
conductor.
Insulation class II . This fan has double insulation and it
must not be connected to the earth connection.
AC - Alternating Current Voltage
Frequency (hertz)
Voltage in volts
Intensity of current in watts
Exclusive use in enclosed spaces.
IP Level of protection against intrusion. You can find the
corresponding protection level on the label of the lamp.
The luminaire can under no circumstances be mounted
on normally flammable surfaces.
Switching it on
Connect to the power supply and check the functioning of
the fan. A series of pulses controls the speed of the fan, as
follows:
Press once - fast; press 2 times - medium speed; press 3
times - slow; press 4 times - off. The speed adjustments to
increase or reduce the temperature will depend on factors
4
/ Do not use the lamp without the glass. If it is
damaged, it must be replaced with a new one
The lamp is designed to use only self-protected tungsten
halogen light bulbs.
Exclusive use in enclosed spaces.
IP Level of protection against intrusion. You can find the
corresponding protection level on the label of the lamp.
The luminaire can under no circumstances be mounted
on normally flammable surfaces.
Switching it on
Connect to the power supply and check the functioning of
the fan. A series of pulses controls the speed of the fan, as
follows:
Press once - fast; press 2 times - medium speed; press 3
times - slow; press 4 times - off. The speed adjustments to
increase or reduce the temperature will depend on factors
such as the size of the room, its height, the number of fans
available, etc. Using the sliding switch, you can control the
direction of the fan, forward or backward.
Hot temperatures/low position - (forward) The fan turns
anti-clockwise. The downward air current creates a cooling
effect, as shown in figure A.
This enables you to set the air conditioning to a higher
temperature without compromising on comfort.
Low temperatures/upper position - (backward) The fan turns
clockwise. The upward air current causes the warm air in the
upper part of the room to move to other areas, as shown in
figure B.
This enables you to set the heating to a lower temperature
without compromising on comfort.
(Before using your fan in this position, consult point 10 of
the safety instructions).
NOTE: Switch the fan off and wait until it has stopped
completely before changing the position of the sliding
switch forward or backward.
Maintenance
1. Due to the normal movement of the fan, it is possible that
some connections may come lose. Check the support
connections, the supports and the attachment of the blades
twice a year. Make sure they are securely attached.
4
/ Do not use the lamp without the glass. If it is
damaged, it must be replaced with a new one
The lamp is designed to use only self-protected tungsten
halogen light bulbs.
Exclusive use in enclosed spaces.
IP Level of protection against intrusion. You can find the
corresponding protection level on the label of the lamp.
The luminaire can under no circumstances be mounted
on normally flammable surfaces.
Switching it on
Connect to the power supply and check the functioning of
the fan. A series of pulses controls the speed of the fan, as
follows:
Press once - fast; press 2 times - medium speed; press 3
times - slow; press 4 times - off. The speed adjustments to
increase or reduce the temperature will depend on factors
such as the size of the room, its height, the number of fans
available, etc. Using the sliding switch, you can control the
direction of the fan, forward or backward.
Hot temperatures/low position - (forward) The fan turns
anti-clockwise. The downward air current creates a cooling
effect, as shown in figure A.
This enables you to set the air conditioning to a higher
temperature without compromising on comfort.
Low temperatures/upper position - (backward) The fan turns
clockwise. The upward air current causes the warm air in the
upper part of the room to move to other areas, as shown in
figure B.
This enables you to set the heating to a lower temperature
without compromising on comfort.
(Before using your fan in this position, consult point 10 of
the safety instructions).
NOTE: Switch the fan off and wait until it has stopped
completely before changing the position of the sliding
switch forward or backward.
Maintenance
1. Due to the normal movement of the fan, it is possible that
some connections may come lose. Check the support
connections, the supports and the attachment of the blades
twice a year. Make sure they are securely attached.
4
/ Do not use the lamp without the glass. If it is
damaged, it must be replaced with a new one
The lamp is designed to use only self-protected tungsten
halogen light bulbs.
Exclusive use in enclosed spaces.
IP Level of protection against intrusion. You can find the
corresponding protection level on the label of the lamp.
The luminaire can under no circumstances be mounted
on normally flammable surfaces.
Switching it on
Connect to the power supply and check the functioning of
the fan. A series of pulses controls the speed of the fan, as
follows:
Press once - fast; press 2 times - medium speed; press 3
times - slow; press 4 times - off. The speed adjustments to
increase or reduce the temperature will depend on factors
such as the size of the room, its height, the number of fans
available, etc. Using the sliding switch, you can control the
direction of the fan, forward or backward.
Hot temperatures/low position - (forward) The fan turns
anti-clockwise. The downward air current creates a cooling
effect, as shown in figure A.
This enables you to set the air conditioning to a higher
temperature without compromising on comfort.
Low temperatures/upper position - (backward) The fan turns
clockwise. The upward air current causes the warm air in the
upper part of the room to move to other areas, as shown in
figure B.
This enables you to set the heating to a lower temperature
without compromising on comfort.
(Before using your fan in this position, consult point 10 of
the safety instructions).
NOTE: Switch the fan off and wait until it has stopped
completely before changing the position of the sliding
switch forward or backward.
Maintenance
1. Due to the normal movement of the fan, it is possible that
some connections may come lose. Check the support
connections, the supports and the attachment of the blades
twice a year. Make sure they are securely attached.

8
220-240V~50Hz
Características do aparelho
Tensãonominale
Frequêncianominal
Classe de proteção
Índice de proteção IP
Potência nominal
Símbolo Função
3 - Alta velocidade
2 - Velocidade média
1 - Baixa velocidade
0 - Desligado
Para cima para o Inverno, para circular ar quente em
toda a divisão.
Para baixo para o Verão, cria um movimento do ar do
teto para baixo.
O interruptor na estrutura do motor para controlar a
direção de rotação das pás controla a direção do
movimento do ar. Cuidado: Antes de usar este
interruptor de direção, desligue a ventoinha e
certifique-se de que esta pára de rodar, para evitar
lesões ou danos no motor.

4
/ Do not use the lamp without the glass. If it is
damaged, it must be replaced with a new one
The lamp is designed to use only self-protected tungsten
halogen light bulbs.
Exclusive use in enclosed spaces.
IP Level of protection against intrusion. You can find the
corresponding protection level on the label of the lamp.
The luminaire can under no circumstances be mounted
on normally flammable surfaces.
Switching it on
Connect to the power supply and check the functioning of
the fan. A series of pulses controls the speed of the fan, as
follows:
Press once - fast; press 2 times - medium speed; press 3
times - slow; press 4 times - off. The speed adjustments to
increase or reduce the temperature will depend on factors
such as the size of the room, its height, the number of fans
available, etc. Using the sliding switch, you can control the
direction of the fan, forward or backward.
Hot temperatures/low position - (forward) The fan turns
anti-clockwise. The downward air current creates a cooling
effect, as shown in figure A.
This enables you to set the air conditioning to a higher
temperature without compromising on comfort.
Low temperatures/upper position - (backward) The fan turns
clockwise. The upward air current causes the warm air in the
upper part of the room to move to other areas, as shown in
figure B.
This enables you to set the heating to a lower temperature
without compromising on comfort.
(Before using your fan in this position, consult point 10 of
the safety instructions).
NOTE: Switch the fan off and wait until it has stopped
completely before changing the position of the sliding
switch forward or backward.
Maintenance
1. Due to the normal movement of the fan, it is possible that
some connections may come lose. Check the support
connections, the supports and the attachment of the blades
twice a year. Make sure they are securely attached.
4
/ Do not use the lamp without the glass. If it is
damaged, it must be replaced with a new one
The lamp is designed to use only self-protected tungsten
halogen light bulbs.
Exclusive use in enclosed spaces.
IP Level of protection against intrusion. You can find the
corresponding protection level on the label of the lamp.
The luminaire can under no circumstances be mounted
on normally flammable surfaces.
Switching it on
Connect to the power supply and check the functioning of
the fan. A series of pulses controls the speed of the fan, as
follows:
Press once - fast; press 2 times - medium speed; press 3
times - slow; press 4 times - off. The speed adjustments to
increase or reduce the temperature will depend on factors
such as the size of the room, its height, the number of fans
available, etc. Using the sliding switch, you can control the
direction of the fan, forward or backward.
Hot temperatures/low position - (forward) The fan turns
anti-clockwise. The downward air current creates a cooling
effect, as shown in figure A.
This enables you to set the air conditioning to a higher
temperature without compromising on comfort.
Low temperatures/upper position - (backward) The fan turns
clockwise. The upward air current causes the warm air in the
upper part of the room to move to other areas, as shown in
figure B.
This enables you to set the heating to a lower temperature
without compromising on comfort.
(Before using your fan in this position, consult point 10 of
the safety instructions).
NOTE: Switch the fan off and wait until it has stopped
completely before changing the position of the sliding
switch forward or backward.
Maintenance
1. Due to the normal movement of the fan, it is possible that
some connections may come lose. Check the support
connections, the supports and the attachment of the blades
twice a year. Make sure they are securely attached.
4
/ Do not use the lamp without the glass. If it is
damaged, it must be replaced with a new one
The lamp is designed to use only self-protected tungsten
halogen light bulbs.
Exclusive use in enclosed spaces.
IP Level of protection against intrusion. You can find the
corresponding protection level on the label of the lamp.
The luminaire can under no circumstances be mounted
on normally flammable surfaces.
Switching it on
Connect to the power supply and check the functioning of
the fan. A series of pulses controls the speed of the fan, as
follows:
Press once - fast; press 2 times - medium speed; press 3
times - slow; press 4 times - off. The speed adjustments to
increase or reduce the temperature will depend on factors
such as the size of the room, its height, the number of fans
available, etc. Using the sliding switch, you can control the
direction of the fan, forward or backward.
Hot temperatures/low position - (forward) The fan turns
anti-clockwise. The downward air current creates a cooling
effect, as shown in figure A.
This enables you to set the air conditioning to a higher
temperature without compromising on comfort.
Low temperatures/upper position - (backward) The fan turns
clockwise. The upward air current causes the warm air in the
upper part of the room to move to other areas, as shown in
figure B.
This enables you to set the heating to a lower temperature
without compromising on comfort.
(Before using your fan in this position, consult point 10 of
the safety instructions).
NOTE: Switch the fan off and wait until it has stopped
completely before changing the position of the sliding
switch forward or backward.
Maintenance
1. Due to the normal movement of the fan, it is possible that
some connections may come lose. Check the support
connections, the supports and the attachment of the blades
twice a year. Make sure they are securely attached.

3
15. This appliance can be used by children aged 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowladge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by
children without supervisions.
16. The means for disconnection from the supply mains
having a contact separation in all poles that provides full
disconnection that must be incorporated in the fixed wiring
in accordance with the wiring rules.
17. Regarding the instructions for the method of fixing and
how to install the fan, thanks to refer to the section
“INSTALLATION”.
18. Regarding the method of the cable connection, thanks to
refer to the section "CABLE INFORMATION".
Description of symbols:
You will find all the symbols related to his lamp on both the
product label and the box in which it came.
Insulation class I . This fan must be connected with its
ground wire (green and yellow cable) to the earthing
conductor.
Insulation class II . This fan has double insulation and it
must not be connected to the earth connection.
AC - Alternating Current Voltage
Frequency (hertz)
Voltage in volts
Intensity of current in watts
Exclusive use in enclosed spaces.
IP Level of protection against intrusion. You can find the
corresponding protection level on the label of the lamp.
The luminaire can under no circumstances be mounted
on normally flammable surfaces.
Switching it on
Connect to the power supply and check the functioning of
the fan. A series of pulses controls the speed of the fan, as
follows:
Press once - fast; press 2 times - medium speed; press 3
times - slow; press 4 times - off. The speed adjustments to
increase or reduce the temperature will depend on factors
4
/ Do not use the lamp without the glass. If it is
damaged, it must be replaced with a new one
The lamp is designed to use only self-protected tungsten
halogen light bulbs.
Exclusive use in enclosed spaces.
IP Level of protection against intrusion. You can find the
corresponding protection level on the label of the lamp.
The luminaire can under no circumstances be mounted
on normally flammable surfaces.
Switching it on
Connect to the power supply and check the functioning of
the fan. A series of pulses controls the speed of the fan, as
follows:
Press once - fast; press 2 times - medium speed; press 3
times - slow; press 4 times - off. The speed adjustments to
increase or reduce the temperature will depend on factors
such as the size of the room, its height, the number of fans
available, etc. Using the sliding switch, you can control the
direction of the fan, forward or backward.
Hot temperatures/low position - (forward) The fan turns
anti-clockwise. The downward air current creates a cooling
effect, as shown in figure A.
This enables you to set the air conditioning to a higher
temperature without compromising on comfort.
Low temperatures/upper position - (backward) The fan turns
clockwise. The upward air current causes the warm air in the
upper part of the room to move to other areas, as shown in
figure B.
This enables you to set the heating to a lower temperature
without compromising on comfort.
(Before using your fan in this position, consult point 10 of
the safety instructions).
NOTE: Switch the fan off and wait until it has stopped
completely before changing the position of the sliding
switch forward or backward.
Maintenance
1. Due to the normal movement of the fan, it is possible that
some connections may come lose. Check the support
connections, the supports and the attachment of the blades
twice a year. Make sure they are securely attached.
4
/ Do not use the lamp without the glass. If it is
damaged, it must be replaced with a new one
The lamp is designed to use only self-protected tungsten
halogen light bulbs.
Exclusive use in enclosed spaces.
IP Level of protection against intrusion. You can find the
corresponding protection level on the label of the lamp.
The luminaire can under no circumstances be mounted
on normally flammable surfaces.
Switching it on
Connect to the power supply and check the functioning of
the fan. A series of pulses controls the speed of the fan, as
follows:
Press once - fast; press 2 times - medium speed; press 3
times - slow; press 4 times - off. The speed adjustments to
increase or reduce the temperature will depend on factors
such as the size of the room, its height, the number of fans
available, etc. Using the sliding switch, you can control the
direction of the fan, forward or backward.
Hot temperatures/low position - (forward) The fan turns
anti-clockwise. The downward air current creates a cooling
effect, as shown in figure A.
This enables you to set the air conditioning to a higher
temperature without compromising on comfort.
Low temperatures/upper position - (backward) The fan turns
clockwise. The upward air current causes the warm air in the
upper part of the room to move to other areas, as shown in
figure B.
This enables you to set the heating to a lower temperature
without compromising on comfort.
(Before using your fan in this position, consult point 10 of
the safety instructions).
NOTE: Switch the fan off and wait until it has stopped
completely before changing the position of the sliding
switch forward or backward.
Maintenance
1. Due to the normal movement of the fan, it is possible that
some connections may come lose. Check the support
connections, the supports and the attachment of the blades
twice a year. Make sure they are securely attached.
4
/ Do not use the lamp without the glass. If it is
damaged, it must be replaced with a new one
The lamp is designed to use only self-protected tungsten
halogen light bulbs.
Exclusive use in enclosed spaces.
IP Level of protection against intrusion. You can find the
corresponding protection level on the label of the lamp.
The luminaire can under no circumstances be mounted
on normally flammable surfaces.
Switching it on
Connect to the power supply and check the functioning of
the fan. A series of pulses controls the speed of the fan, as
follows:
Press once - fast; press 2 times - medium speed; press 3
times - slow; press 4 times - off. The speed adjustments to
increase or reduce the temperature will depend on factors
such as the size of the room, its height, the number of fans
available, etc. Using the sliding switch, you can control the
direction of the fan, forward or backward.
Hot temperatures/low position - (forward) The fan turns
anti-clockwise. The downward air current creates a cooling
effect, as shown in figure A.
This enables you to set the air conditioning to a higher
temperature without compromising on comfort.
Low temperatures/upper position - (backward) The fan turns
clockwise. The upward air current causes the warm air in the
upper part of the room to move to other areas, as shown in
figure B.
This enables you to set the heating to a lower temperature
without compromising on comfort.
(Before using your fan in this position, consult point 10 of
the safety instructions).
NOTE: Switch the fan off and wait until it has stopped
completely before changing the position of the sliding
switch forward or backward.
Maintenance
1. Due to the normal movement of the fan, it is possible that
some connections may come lose. Check the support
connections, the supports and the attachment of the blades
twice a year. Make sure they are securely attached.
4
/ Do not use the lamp without the glass. If it is
damaged, it must be replaced with a new one
The lamp is designed to use only self-protected tungsten
halogen light bulbs.
Exclusive use in enclosed spaces.
IP Level of protection against intrusion. You can find the
corresponding protection level on the label of the lamp.
The luminaire can under no circumstances be mounted
on normally flammable surfaces.
Switching it on
Connect to the power supply and check the functioning of
the fan. A series of pulses controls the speed of the fan, as
follows:
Press once - fast; press 2 times - medium speed; press 3
times - slow; press 4 times - off. The speed adjustments to
increase or reduce the temperature will depend on factors
such as the size of the room, its height, the number of fans
available, etc. Using the sliding switch, you can control the
direction of the fan, forward or backward.
Hot temperatures/low position - (forward) The fan turns
anti-clockwise. The downward air current creates a cooling
effect, as shown in figure A.
This enables you to set the air conditioning to a higher
temperature without compromising on comfort.
Low temperatures/upper position - (backward) The fan turns
clockwise. The upward air current causes the warm air in the
upper part of the room to move to other areas, as shown in
figure B.
This enables you to set the heating to a lower temperature
without compromising on comfort.
(Before using your fan in this position, consult point 10 of
the safety instructions).
NOTE: Switch the fan off and wait until it has stopped
completely before changing the position of the sliding
switch forward or backward.
Maintenance
1. Due to the normal movement of the fan, it is possible that
some connections may come lose. Check the support
connections, the supports and the attachment of the blades
twice a year. Make sure they are securely attached.
4
/ Do not use the lamp without the glass. If it is
damaged, it must be replaced with a new one
The lamp is designed to use only self-protected tungsten
halogen light bulbs.
Exclusive use in enclosed spaces.
IP Level of protection against intrusion. You can find the
corresponding protection level on the label of the lamp.
The luminaire can under no circumstances be mounted
on normally flammable surfaces.
Switching it on
Connect to the power supply and check the functioning of
the fan. A series of pulses controls the speed of the fan, as
follows:
Press once - fast; press 2 times - medium speed; press 3
times - slow; press 4 times - off. The speed adjustments to
increase or reduce the temperature will depend on factors
such as the size of the room, its height, the number of fans
available, etc. Using the sliding switch, you can control the
direction of the fan, forward or backward.
Hot temperatures/low position - (forward) The fan turns
anti-clockwise. The downward air current creates a cooling
effect, as shown in figure A.
This enables you to set the air conditioning to a higher
temperature without compromising on comfort.
Low temperatures/upper position - (backward) The fan turns
clockwise. The upward air current causes the warm air in the
upper part of the room to move to other areas, as shown in
figure B.
This enables you to set the heating to a lower temperature
without compromising on comfort.
(Before using your fan in this position, consult point 10 of
the safety instructions).
NOTE: Switch the fan off and wait until it has stopped
completely before changing the position of the sliding
switch forward or backward.
Maintenance
1. Due to the normal movement of the fan, it is possible that
some connections may come lose. Check the support
connections, the supports and the attachment of the blades
twice a year. Make sure they are securely attached.
4
/ Do not use the lamp without the glass. If it is
damaged, it must be replaced with a new one
The lamp is designed to use only self-protected tungsten
halogen light bulbs.
Exclusive use in enclosed spaces.
IP Level of protection against intrusion. You can find the
corresponding protection level on the label of the lamp.
The luminaire can under no circumstances be mounted
on normally flammable surfaces.
Switching it on
Connect to the power supply and check the functioning of
the fan. A series of pulses controls the speed of the fan, as
follows:
Press once - fast; press 2 times - medium speed; press 3
times - slow; press 4 times - off. The speed adjustments to
increase or reduce the temperature will depend on factors
such as the size of the room, its height, the number of fans
available, etc. Using the sliding switch, you can control the
direction of the fan, forward or backward.
Hot temperatures/low position - (forward) The fan turns
anti-clockwise. The downward air current creates a cooling
effect, as shown in figure A.
This enables you to set the air conditioning to a higher
temperature without compromising on comfort.
Low temperatures/upper position - (backward) The fan turns
clockwise. The upward air current causes the warm air in the
upper part of the room to move to other areas, as shown in
figure B.
This enables you to set the heating to a lower temperature
without compromising on comfort.
(Before using your fan in this position, consult point 10 of
the safety instructions).
NOTE: Switch the fan off and wait until it has stopped
completely before changing the position of the sliding
switch forward or backward.
Maintenance
1. Due to the normal movement of the fan, it is possible that
some connections may come lose. Check the support
connections, the supports and the attachment of the blades
twice a year. Make sure they are securely attached.

8
Symbol Function
The switch on the motor housing for controlling the
fan blades rotating direction controls the direction
of air movement. Caution: Before using this rotating
direction switch, turn OFF the fan and ensure the
fan stops rotating to prevent injury to yourself and
damage to the motor.
Left for summer creates air movement down from
the ceiling.
Right for winter to circulate warm air around the
room.

4
/ Do not use the lamp without the glass. If it is
damaged, it must be replaced with a new one
The lamp is designed to use only self-protected tungsten
halogen light bulbs.
Exclusive use in enclosed spaces.
IP Level of protection against intrusion. You can find the
corresponding protection level on the label of the lamp.
The luminaire can under no circumstances be mounted
on normally flammable surfaces.
Switching it on
Connect to the power supply and check the functioning of
the fan. A series of pulses controls the speed of the fan, as
follows:
Press once - fast; press 2 times - medium speed; press 3
times - slow; press 4 times - off. The speed adjustments to
increase or reduce the temperature will depend on factors
such as the size of the room, its height, the number of fans
available, etc. Using the sliding switch, you can control the
direction of the fan, forward or backward.
Hot temperatures/low position - (forward) The fan turns
anti-clockwise. The downward air current creates a cooling
effect, as shown in figure A.
This enables you to set the air conditioning to a higher
temperature without compromising on comfort.
Low temperatures/upper position - (backward) The fan turns
clockwise. The upward air current causes the warm air in the
upper part of the room to move to other areas, as shown in
figure B.
This enables you to set the heating to a lower temperature
without compromising on comfort.
(Before using your fan in this position, consult point 10 of
the safety instructions).
NOTE: Switch the fan off and wait until it has stopped
completely before changing the position of the sliding
switch forward or backward.
Maintenance
1. Due to the normal movement of the fan, it is possible that
some connections may come lose. Check the support
connections, the supports and the attachment of the blades
twice a year. Make sure they are securely attached.
4
/ Do not use the lamp without the glass. If it is
damaged, it must be replaced with a new one
The lamp is designed to use only self-protected tungsten
halogen light bulbs.
Exclusive use in enclosed spaces.
IP Level of protection against intrusion. You can find the
corresponding protection level on the label of the lamp.
The luminaire can under no circumstances be mounted
on normally flammable surfaces.
Switching it on
Connect to the power supply and check the functioning of
the fan. A series of pulses controls the speed of the fan, as
follows:
Press once - fast; press 2 times - medium speed; press 3
times - slow; press 4 times - off. The speed adjustments to
increase or reduce the temperature will depend on factors
such as the size of the room, its height, the number of fans
available, etc. Using the sliding switch, you can control the
direction of the fan, forward or backward.
Hot temperatures/low position - (forward) The fan turns
anti-clockwise. The downward air current creates a cooling
effect, as shown in figure A.
This enables you to set the air conditioning to a higher
temperature without compromising on comfort.
Low temperatures/upper position - (backward) The fan turns
clockwise. The upward air current causes the warm air in the
upper part of the room to move to other areas, as shown in
figure B.
This enables you to set the heating to a lower temperature
without compromising on comfort.
(Before using your fan in this position, consult point 10 of
the safety instructions).
NOTE: Switch the fan off and wait until it has stopped
completely before changing the position of the sliding
switch forward or backward.
Maintenance
1. Due to the normal movement of the fan, it is possible that
some connections may come lose. Check the support
connections, the supports and the attachment of the blades
twice a year. Make sure they are securely attached.

4
/ Do not use the lamp without the glass. If it is
damaged, it must be replaced with a new one
The lamp is designed to use only self-protected tungsten
halogen light bulbs.
Exclusive use in enclosed spaces.
IP Level of protection against intrusion. You can find the
corresponding protection level on the label of the lamp.
The luminaire can under no circumstances be mounted
on normally flammable surfaces.
Switching it on
Connect to the power supply and check the functioning of
the fan. A series of pulses controls the speed of the fan, as
follows:
Press once - fast; press 2 times - medium speed; press 3
times - slow; press 4 times - off. The speed adjustments to
increase or reduce the temperature will depend on factors
such as the size of the room, its height, the number of fans
available, etc. Using the sliding switch, you can control the
direction of the fan, forward or backward.
Hot temperatures/low position - (forward) The fan turns
anti-clockwise. The downward air current creates a cooling
effect, as shown in figure A.
This enables you to set the air conditioning to a higher
temperature without compromising on comfort.
Low temperatures/upper position - (backward) The fan turns
clockwise. The upward air current causes the warm air in the
upper part of the room to move to other areas, as shown in
figure B.
This enables you to set the heating to a lower temperature
without compromising on comfort.
(Before using your fan in this position, consult point 10 of
the safety instructions).
NOTE: Switch the fan off and wait until it has stopped
completely before changing the position of the sliding
switch forward or backward.
Maintenance
1. Due to the normal movement of the fan, it is possible that
some connections may come lose. Check the support
connections, the supports and the attachment of the blades
twice a year. Make sure they are securely attached.
4
/ Do not use the lamp without the glass. If it is
damaged, it must be replaced with a new one
The lamp is designed to use only self-protected tungsten
halogen light bulbs.
Exclusive use in enclosed spaces.
IP Level of protection against intrusion. You can find the
corresponding protection level on the label of the lamp.
The luminaire can under no circumstances be mounted
on normally flammable surfaces.
Switching it on
Connect to the power supply and check the functioning of
the fan. A series of pulses controls the speed of the fan, as
follows:
Press once - fast; press 2 times - medium speed; press 3
times - slow; press 4 times - off. The speed adjustments to
increase or reduce the temperature will depend on factors
such as the size of the room, its height, the number of fans
available, etc. Using the sliding switch, you can control the
direction of the fan, forward or backward.
Hot temperatures/low position - (forward) The fan turns
anti-clockwise. The downward air current creates a cooling
effect, as shown in figure A.
This enables you to set the air conditioning to a higher
temperature without compromising on comfort.
Low temperatures/upper position - (backward) The fan turns
clockwise. The upward air current causes the warm air in the
upper part of the room to move to other areas, as shown in
figure B.
This enables you to set the heating to a lower temperature
without compromising on comfort.
(Before using your fan in this position, consult point 10 of
the safety instructions).
NOTE: Switch the fan off and wait until it has stopped
completely before changing the position of the sliding
switch forward or backward.
Maintenance
1. Due to the normal movement of the fan, it is possible that
some connections may come lose. Check the support
connections, the supports and the attachment of the blades
twice a year. Make sure they are securely attached.
4
/ Do not use the lamp without the glass. If it is
damaged, it must be replaced with a new one
The lamp is designed to use only self-protected tungsten
halogen light bulbs.
Exclusive use in enclosed spaces.
IP Level of protection against intrusion. You can find the
corresponding protection level on the label of the lamp.
The luminaire can under no circumstances be mounted
on normally flammable surfaces.
Switching it on
Connect to the power supply and check the functioning of
the fan. A series of pulses controls the speed of the fan, as
follows:
Press once - fast; press 2 times - medium speed; press 3
times - slow; press 4 times - off. The speed adjustments to
increase or reduce the temperature will depend on factors
such as the size of the room, its height, the number of fans
available, etc. Using the sliding switch, you can control the
direction of the fan, forward or backward.
Hot temperatures/low position - (forward) The fan turns
anti-clockwise. The downward air current creates a cooling
effect, as shown in figure A.
This enables you to set the air conditioning to a higher
temperature without compromising on comfort.
Low temperatures/upper position - (backward) The fan turns
clockwise. The upward air current causes the warm air in the
upper part of the room to move to other areas, as shown in
figure B.
This enables you to set the heating to a lower temperature
without compromising on comfort.
(Before using your fan in this position, consult point 10 of
the safety instructions).
NOTE: Switch the fan off and wait until it has stopped
completely before changing the position of the sliding
switch forward or backward.
Maintenance
1. Due to the normal movement of the fan, it is possible that
some connections may come lose. Check the support
connections, the supports and the attachment of the blades
twice a year. Make sure they are securely attached.