EGig eG8TS User manual

8 Port Nway Fast Ethernet Switch
User's Manual
FDX
10/100M
LINK/ACT
POWER
12345678
DC 7.5V
NORMAL UPLINK

FCC Warning
This device has been tested and found to comply with limits for
a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses
and radiates radio frequency energy and, if not installed and
used in accordance with the user's manual, may cause
interference in which case user will be required to correct the
interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this
product may cause radio interference in which case the user
may be required to take adequate measures.

Table Of Contents
Chapter 1 -------------------------------------------------------------------1
Introduction---------------------------------------------------------------------1
KeyFeatures-------------------------------------------------------------------2
Chapter 2 -------------------------------------------------------------------3
PackageContents------------------------------------------------------------3
Chapter 3 -------------------------------------------------------------------4
Front Panel Layout -----------------------------------------------------------4
8 RJ-45 10/100Mbps Switch Ports ----------------------------------4
Power DC 7.5V ----------------------------------------------------------4
NORMAL/UPLINK Switch ---------------------------------------------5
Uplink Port ----------------------------------------------------------------5
LED Indicators of 8 Port 10/100Mps Switch ----------------------6
LED Definitions ----------------------------------------------------------7
Power LED --------------------------------------------------------------7
FDX LED -----------------------------------------------------------------7
10/100M LED -----------------------------------------------------------7
LINK/ACT LED ---------------------------------------------------------7
Chapter 4 -------------------------------------------------------------------8
Installation ----------------------------------------------------------------------8
ToconnecttheSwitchtoPCs,servers,andother
network devices.----------------------------------------------------------8
To connect the Switch to a Switch or a Hub -----------------------9
Chapter 5 -----------------------------------------------------------------10
Technical Specifications ---------------------------------------------------10
I.
II.
III.
IV.
V.
VI.
I.
II.

Chapter 1
8 Port Nway Fast Ethernet Switch
Introduction
The Switch provides 8 10/100Mbps ports. The Switch was designed
for easy installation and high performance in an environment where
traffic on the network and the number of user increase continuously.
The small, compact rigid size was specifically designed for small to
medium workgroups. The Switch can be installed where space is
limited; moreover it provides smooth network migration and easy
upgrade to network capacity.
-1-
FDX
10/100M
LINK/ACT
POWER
12345678
DC 7.5V
NORMAL UPLINK

Key Features
8 Port 10/100BASE T/TX Nway (Auto-negotiation)
Switch with RJ-45 connectors
Palm size with transparent enclosure design
Auto-detect of Full/Half-duplex modes in all ports
Dedicated Full-duplex 200Mbps bandwidth on each
port
Broadcast storm control
Store & Forward switching methods
IEEE 802.3x flow control for Full-duplex
Zero-Packet Loss Back-pressure flow control for
Half-duplex
Non-blocking & Non-head-of-line blocking full wire
speed forwarding
Auto-learning of networking configurations
Status LEDs: Power, Speed, Link/Activity and
Full/Half-duplex
Low power consumption
Smart plug & play
-2-

Chapter 2
Package Contents
Before you start to install the Switch, please verify your package
that containsthe following items:
One Fast Ethernet Switch
One Power Adapter
One User's Manual
Magnet (optional)
Note: If any of these items is found missing or damaged, please
contact your local supplier for replacement.
-3-
8 Port Nway Fast Ethernet Switch
User's Manual
8 Port Switch
Power Adapter
Magnet
User's Manual
FDX
10/100M
LINK/ACT
POWER
12345678
DC 7.5V
NORMAL UPLINK
FDX
10/100M
LINK/ACT
POWER
12345678
DC 7.5V
NORMAL UPLINK

Chapter 3
Front Panel Layout
I. 8 RJ-45 10/100Mbps Switch Ports
There are 1~8 RJ-45 connector on the front panel for connecting to
servers, workstation or other devices. The Switch provides 8
10/100Mbps switching ports that could sense the 10/100M speed
and negotiate Full/Half-duplex mode automatically. These switching
ports allow users connect the Switch to 10BASE-T and 100BASE-TX
devices.
II. Power DC 7.5V/1.5A
Power adapter.
-4-
Uplink Switch
Uplink Port
DC Jack
1 2 345 6 7 8
DC 7.5V
NORMAL UPLINK
RJ-45 Port

III. NORMAL/UPLINK Switch
One NORMAL/UPLINK switch on the front panel allows users to
select connecting to a PC or a Hub/Switch. The default setting is in
the "NORMAL" position. The port is configured to connect with a PC.
When the switch is pushed forward in "UPLINK" position, it allows
users to connect with a Hub or a Switch using straight-through
twisted pair cable.
IV. Uplink Port
Shared with the port #1 for expanding to another Hub or Switch. The
Uplink port and port 1 share the same port & function. Do not use
both of the Uplink port and port 1 at the same time.
-5-
NORMAL UPLINK
NORMAL UPLINK
NORMAL UPLINK
1 2 345 6 7 8
DC 7.5V
NORMAL UPLINK
1 2 345 6 7 8
DC 7.5V
NORMAL UPLINK
1

V.LED Indicators of 8 Port 10/100Mps Switch
LED Color Status Description No. Of LED
Power Yellow On Power on 1
FDX Green On Full-duplex 8(1~8)
Off Half-duplex 8(1~8)
Flashing Partial collision 8(1~8)
occurs
10/100M Green On Port is on the 8(1~8)
100M status
Off Port is on the 8(1~8)
10M status
LINK/ACT Yellow On 10/100Mbps port 8(1~8)
for connection
Flashing 10/100Mbps for 8(1~8)
data activating
-6-
POWER
1 2 3 4 5 6 7 8
FDX
10/100M
LINK/ACT
Yellow Green Green

VI. LED Definitions
Power LED
On : The unit is powered on and ready for use.
Off : The unit is powered off.
FDX
On : The port is operating at Full-duplex.
Off
Flashing : Collisions occurred and the port is
operating at Half-duplex mode.
10/100M LED
On : The port is on the 100Mbps status.
Off : The port is on the 10Mbps status.
LINK/ACT LED
On : The port is ready for 10/100Mbps
connection
Flashing : The data is transmitted or received on
the port.
-7-
: The port is operating at Half-duplex
without any data being transmitted or
received.