EIPL AM2000 User manual

UK Head Office
Ebac Industrial Products Ltd
St Helens Trading Estate
Bishop Auckland
County Durham
DL14 9AD
Tel: [phone]
Fax: [phone]
www.eipl.co.uk
[email protected]
American Sales Office
Ebac Industrial Products Inc
700 Thimble Shoals Blvd.
Suite 109, Newport News
Virginia, 23606-2575
USA
Tel: [phone]
Fax: [phone]
www.ebacusa.com
[email protected]
German Sales Office
Ebac Industrial Products Ltd
Tel: [phone]
Fax: [phone]
AM2000
AIR
USER MANUAL
German Sales Office
Ebac Industrial Products Ltd
Miraustra 64 – 66
13509
Berlin
Germany
Tel: [phone]
Fax: [phone]
www.eip-ltd.de
[email protected]
AM2000
MOVER
USER MANUAL
Drawing No.
:
-
TPC
403
Issue :- 1
Date :- 01/10/13
For service questions, contact
Ebac at 1-757-873-6800.
For sales inquiries, contact
Sylvane at 1-800-934-9194.

IF YOUR
AIRMOVER
FAILS TO
OPERATE
1.
Check that the plug is fully pushed
into the socket and is switched on.
2.
Check with some other electrical
device that the wall socket is “live”. If
it is not, contact a qualified
electrician.
3. Check the
circuit breaker on the
control panel and reset as required.
Should none of the above remedies
work, then disconnect from the mains.
Contact your supplier
. DO NOT attempt
to repair the unit or unscrew the outer
casing.
UNPACKING
Remove the top insert and your E
IPL
Air M
over from its packing carton,
v
isually inspect for any signs of transit
damage. If there are any signs of
damage, do not operate your unit. Call
your supplier immediately for advice. Do
not discard the packing for it will be
useful for transporting your un
it in the
future.
TRANSPORTATION
A cord wrapping facility has been
moulded into the plastic fan housing.
The power cord should be wrapped
around this facility during transit. Do not
drop or abuse your Air M
over during
transit for risk of damage to both th
e
motor and housing.
ELECTRICAL CONNECTION
If the appliance is fitted with a plug for
which your socket is unsuitable, then it
should be cut off
and an appropriate plug
fitted.
INTRODUCTION
EIPL
Air Movers are high performance,
high efficiency fan systems designed to
optimize air movement and minimize
operating costs for drying applications.
Each model incorporates a double
inlet,
centrifugal type fan design to provide the
high static pressure and airflow required
to dry water damaged facilities and
equipment. The EIPL
Air Mover series
was designed to provide you the best
performance and serviceability.
•
25 ft. Power Cord with cord grip
•
Internal thermal Circuit Breaker
•
Aerodynamic, Rotationally Moulded
Polythene Housing.
•
High Efficient 1/2 HP Motor
•
Three Speed Fan Design
•
4 operating Positions (0º, 12º, 45º, &
90º)
•
Stack ability in the Vertical Plane
during both Storage and Operation.
•
Moulded Cord wrap Facility
OPERATING PROCEDURES
Connect the power cord into a
grounded
electrical outlet and
turn the power
switch to the ON position.
If you have no
power or hear any
loud or abnormal
noises and consult your supplier.
Your EIPL
Air Mover is designed to
operate in 4 positions to allow drying of
floors, walls and ceilings.
Your EIPL Air Mover co
mes with internal
circuit protection for your safety. When
working around a wet environment, we
also recommend always plugging the
unit into a ground fault interrupter to
assure the best protection.
For the drying of water damaged
facilities, we recommend using an EIPL
dehumidifier along with your air mover to
provide you with more efficient drying.
Your air mover is designed to induce
evaporation or water contained within
flooded surfaces or materials. Yet,
without a mechanism for
removing the
moisture fr
om the air, drying will not
occur. It is recommended that the
dehumidifier outlet is close to the air
mover intake. This allows for dry air to
be distributed by the air mover.
•This machine should be serviced by qualified Ebac
personnel or other persons
having technical competence servicing refrigeration equipment following the
instructions in the Ebac service manual.
•
Ebac service manuals and spares lists are available upon request by contacting
your local Ebac distributor.
•Never operate the unit in a bathroom or swimming pool area
•Do not use the machine if the power cord or case are damaged.
•Do not poke objects into and of the grilles on the machine.
•Do not cover or obstruct the air inlet or outlet.
•This machine complies with the electromagnetic compatibility 1992 regulations.
•
This machine has been manufactured in the United Kingdom.
TECHNICAL SPECIFICATIONS
AM2000 115V/60Hz/1
Phase
Height 21”
Width 20”
Depth 19”
Weight 34lbs
Horsepower ½
Max running current 5A
Fan Speeds 3
IMPORTANT
As the colours of the wires in the mains
lead of this appliance may
not correspond
with the coloured markings identifying the
terminals in your own plug, proceed as
follows:
The wire which is coloured Green and
Yellow must be connected to the terminal
in the plug which is marked with the letter
E or by the Earth Symbol or
coloured
Green and Yellow. The wire which is
coloured Blue must be connected to the
terminal in the plug which is marked with
the letter N or coloured Black. The wire
which is coloured Brown must be
connected to the terminal which is marked
with the letter L or coloured Red.
You must dispose of the non rewireable
plug once it has been removed from the
flexible cord. It is dangerous to attempt to
insert the plug into any electrical socket
elsewhere in the house. If the flexible cord
becomes damaged it must
be replaced by
an identical cord.
This appliance complies with the
suppression requirements of the EEC
direction 82/199/EEC as embodied in
BS800:1988.
IMPORTANT:- The wires in this mains
lead are coloured in accordance with the
following code:-
Green Earth
White Neutral
Black Live
WARNING
–
THIS APPLIANCE MUST BE EARTHED