Eizo DuralVision FDF2304W-IP User manual

Color LCD Monitor
Installation Manual
Important
Please read this Installation Manual, the Instruction Manual and the
Setup Manual carefully to familiarize yourself with safe and effective
usage.
• The latest manual is available for download from our web site:
http://www.eizoglobal.com

2
About this manual
Setup Manual Describes precautions and setup processes from network camera
connection to camera image display.
Instruction Manual Describes operation of network cameras and live image screen
menus, etc.
Installation Manual
(this manual)
Describes network camera registration and function setup, monitor
system setup, etc.
This product has been adjusted specically for use in the region to which it was originally shipped. If
operated outside this region, the product may not perform as stated in the specications.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by
any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
EIZO Corporation is under no obligation to hold any submitted material or information condential unless
prior arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every
effort has been made to ensure that this manual provides up-to-date information, please note that EIZO
monitor specications are subject to change without notice.

3
Notice for this monitor
Notice for this monitor
This product is suited for displaying surveillance camera images.
This product has been adjusted specically for use in the region to which it was originally shipped. If the
product is used outside the region, it may not operate as specied in the specications.
This product may not be covered by warranty for uses other than those described in this manual.
The specications noted in this manual are only applicable when the following are used:
• Power cords provided with the product
• Signal cables specied by us
Only use optional products manufactured or specied by us with this product.
When installing the monitor in a rack, ensure that there is adequate space around the sides, back and top of
the monitor.
If you place this product on a lacquer-coated desk, the color may adhere to the bottom of the stand due to
the composition of the rubber. Check the desk surface before use.
It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more
after the monitor power has been turned on, and then adjust the monitor.
Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term use and
maintain a stable display.
When the screen image is changed after displaying the same image for extended periods of time, an
afterimage may appear. Use the screen saver or power save function to avoid displaying the same image for
extended periods of time.
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (For
details, refer to the Instruction Manual.).
The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit pixels may
appear on the LCD panel, this is not a malfunction. Percentage of effective dots: 99.9994 % or higher.
The backlight of the LCD panel has a xed lifetime. When the screen becomes dark or begins to icker,
please contact your local EIZO representative.
Do not press on the panel or edge of the frame strongly, as this may result in display malfunctions, such
as interference patterns, etc. If pressure is continually applied to the panel, it may deteriorate or damage
your panel. (If the pressure marks remain on the panel, leave the monitor with a black or white screen. The
symptom may disappear.)
Do not scratch or press on the panel with any sharp objects, as this may result in damage to the panel. Do
not attempt to brush with tissues as this may scratch the panel.
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew
condensation may occur on the interior and exterior surfaces of the monitor. In that case, do not turn the
monitor on. Instead wait until the dew condensation disappears, otherwise it may cause some damage to the
monitor.

4Notice for this monitor
Disclaimer
EIZO shall not be liable in any way to any person whatsoever for the occurrences described below.
1. Any incidental, special or consequential disruption or damage directly or indirectly arising in
connection with this product.
2. Any loss, damage or cost resulting from misuse or neglect.
3. Any malfunction or failure occurring after unauthorized disassembly, repair or alteration regardless
of its cause.
4. Any inconvenience, loss or damage caused by the inability to display images due to any reason or
cause including malfunctions or failures in this product.
5. Any failure or consequential inconvenience, loss or damage due to malfunction or failure of a
combined system that comprises this product and any third party products.
6. Any consequential claim for compensation or complaint based on privacy violation or any other
reason by individuals or entities recorded in the surveillance images which are made public for/by
whatever cause or used.
7. Any loss of registered data for whatever cause.
While this product displays camera surveillance images, the use of this product alone does not directly
prevent crime.
Cautions for Network Use
Because this product is used by connecting to networks, the following risks apply
1. Leakage of information through this product.
2. Unauthorized operation of this product by a malicious third party.
3. Interference or suspension of the use of this product by a malicious third party.
In order to prevent the above described damage, it is the user’s responsibility to implement adequate
network security measures including the measures described below.
• Use this product with a safety-ensured network by using a rewall or other network security
systems.
• Change the administrator password periodically.

5
CONTENTS
CONTENTS
Notice for this monitor ......................................... 3
Disclaimer ................................................................. 4
Cautions for Network Use ....................................... 4
CONTENTS............................................................. 5
Chapter 1 Product overview.............................. 6
1-1. Features ......................................................... 6
1-2. SystemConguration .................................. 7
1-3. Supported Network Cameras...................... 7
Chapter 2 Conguringfromthemonitorscreen ... 8
2-1. BeforeConguration.................................... 8
2-2. Setting Screen............................................... 9
●Basic operations.............................................. 9
2-3. Setting Network Cameras...........................11
●
To automatically discover network cameras ...11
●To manually register network cameras ..........12
●To set network camera functions ...................14
2-4. Setting Display Positions of
Camera Images ........................................... 20
2-5. Setting Smart Functions .............................21
2-6. ConguringSystemSettings .................... 22
2-7. Setting User Information............................ 32
●To register new user information................... 32
●To change user information .......................... 33
●To delete user information............................. 33
2-8. Displaying Operation Logs........................ 34
●To display log data ........................................ 34
●To save log data ............................................ 35
Chapter 3 ConguringfromaWebBrowser ... 36
3-1. BeforeConguration.................................. 36
3-2. Setting Screen..............................................37
●Basic Operations............................................37
3-3. Basic Information ....................................... 38
●System Status ............................................... 38
●Camera and Display Position/Date
and TimeSettings/Network Settings/
Communication Settings............................... 39
3-4. Setting Network Cameras.......................... 40
●To automatically detect cameras .................. 40
●Reading CSV Files.........................................42
●Adding a Camera .......................................... 43
●Changing Camera Information...................... 45
●Deleting Camera Information.........................47
●Save Camera Information ............................. 48
3-5. Setting Display Positions of
Camera Images ........................................... 48
●Setting Display Positions .............................. 49
●Other Display Settings .................................. 50
●Setting Smart Functions.................................51
3-6. ConguringSystemSettings .................... 52
●Date and Time................................................52
●Network Settings........................................... 55
●Communication Settings............................... 56
●Other System Settings .................................. 57
●Maintenance.................................................. 58
3-7. Setting User Information.............................61
●Adding User Information ................................61
●Changing User Information........................... 62
●To delete user information............................. 63
3-8. Displaying Operation Logs........................ 64
●Displaying logs .............................................. 64
●Displaying the system log ............................. 64
3-9. Setting the Live Image Screen .................. 65
Chapter 4 Troubleshooting.............................. 66
4-1. Imaging problems ....................................... 66
4-2. Setting Problems ........................................ 67
Chapter 5 Reference ........................................ 68
5-1. List of setting items.................................... 68
Chapter 6 Glossary .......................................... 73

6Chapter 1 Product overview
Chapter 1 Product overview
This color LCD monitor can display images from up to 16 network cameras*1.
This manual describes network camera setup, monitor system setup and specications, etc.
For information on setup, see “Chapter 2 Conguring from the monitor screen” (page 8) and “Chapter 3
Conguring from a Web Browser” (page 36).
*1 A type of camera which converts images into network signals and transmits the signals.
1-1. Features
• 23.0″ wide format LCD
• Supports a resolution of 1920 × 1080
• LCD panel with wide eld of view adopted
IPS LCD panel with 178° horizontal and vertical viewing angles
• LED backlight LCD panel
No mercury, a hazardous substance, is used.
• Receives input video signals from network cameras.
- Compatible with video compression formats H.264 and MJPEG.
- Up to 16 network cameras can be registered and displayed.
- Images from multiple network cameras can be displayed simultaneously (1-/4-/8-/9-/16-screen
display).
- Network cameras can be controlled from the monitor.
- Unicast and Multicast video signals can be displayed.
• Equipped with Easy Setup function
Necessary settings for setup can be performed with a wizard.
• Compatible with ONVIF Prole S
• Provides display modes (DAY/NIGHT) suitable for surveillance camera images
• EIZO’s unique “Smart” technology
- Smart Resolution function
This function adjusts the perceived resolution of the images so that the blurs are reduced and images are
displayed vividly and clearly.
- Smart Insight function
This function analyzes the image and corrects the brightness for each pixel to make dark area of images
visible.
- Noise Reduction function
This function reduces the amount of block noise that occurs due to video compression.
• Can be operated remotely with the remote control.
• You can register a network camera and congure the live image screen using your web browser
• You can have an alert displayed on the live image screen when communication with a network
camera is lost.
• You can save the settings to a USB storage device and load the settings.
• A 2-year long-term warranty for 24-hour continuous use

7
Chapter 1 Product overview
1-2. SystemConguration
You can communicate with network cameras, display video on the monitor, operate cameras, and so on.
FDF2304W-IP
HDMI
Ethernet
Network camera*1
Network hub
HDMI device*2
(Network video recorder etc.)
*1 Up to 16 network cameras can be registered.
*2 Use an HDMI device (e.g. network video recorder) if necessary.
1-3. Supported Network Cameras
This product supports the following network cameras:
• Panasonic i-pro series network cameras
• ONVIF Prole S-compatible network cameras
Attention
• Supported network cameras vary depending on the monitor’s software version. Check the software version of
the monitor you are using, then check our website (http://www.eizoglobal.com) for details on supported network
cameras. For information on how to check the software version, see “2-6. Conguring System Settings” (page
22).
• For installation and settings of network cameras, also check the network camera’s manual.

8Chapter 2 Conguring from the monitor screen
Chapter 2 Conguringfromthemonitor
screen
You can congure and operate network cameras from the monitor screen. To congure from your web
browser, see “Chapter 3 Conguring from a Web Browser” (page 36).
2-1. BeforeConguration
To congure from the monitor screen, you need to be logged in to the system.
Conguration of this product is allowed only by ADMIN level users.
Be sure to log in to the system with a user account of this level.
Procedure
1. Press on the front of the monitor or on the remote control.
The power indicator lights up blue and the live image screen is displayed.
(For information on the live image screen, refer to the Installation Manual.
2. Select (Login) under “System”.
The login screen is displayed.
5
2
3
4
3. Enter a username and a password.
4. Select “Login”.
The display changes back to the live image screen.
5. Select (Setting).
The setting screen is displayed.
(For information on the setting screen, see “2-2. Setting Screen” (page 9).
Note
• See “To enter characters” (page 10) for the character entry method.
• The following user information is set by default:
- Username: “admin”
- Password: “admin”
- User Level: “ADMIN”
• For information on user settings, see “2-7. Setting User Information” (page 32).
• It is recommended that you log out after completing the setup, so as to prevent a third party from operating
the network camera or altering the settings.
Attention
• When the monitor power is turned off while the user is logged in, the user is logged out from the system
automatically. In such a case, you cannot display the web interface in your web browser.

9
Chapter 2 Conguring from the monitor screen
2-2. Setting Screen
The setting screen is used for various settings such as network camera registration and monitor system
settings.
●Basic operations
List of setting items The setting screen of the selected item is displayed.
To select an item
Press the / / / buttons.
Toconrmaselecteditem
Press .
To change a setting
• With setting buttons Press .
• With list box 1. Press .
An option list is displayed.
2. Select the setting with or .
3. Press .
To return to the previous menu level
Press .
Note
• When canceling a setting change in process, press .

10 Chapter 2 Conguring from the monitor screen
To enter characters
1. Press .
The text eld is highlighted in green.
2. Press the number buttons ( to ).
Press a button consecutively to change over to the character next in order. For the order of character entry,
refer to the table shown below.
Button Input characters
0- _ :. / (space)
1
a b c ABC2
d e f D E F 3
g h i G H I 4
jklJK L 5
m n o M N O6
p q r s P Q R S 7
t u v T U V 8
wxyzW X Y Z 9
To enter a new character, press .
To delete a character, press .
3. Press .
Note
• Entering network addresses
Network address text boxes are separated by [.] (a period mark).
- When a three-digit number is entered, the cursor automatically moves to the next entry position.
- When entering a two-digit or one-digit number, press to move to the next entry position.
- When using a mouse, enter [.] (a period mark) to move to the next entry position.
To exit the setting screen
1. Select “Exit” from the list of setting items with .
2. Press .
Attention
• While settings are being applied (registered) to the system, a “Setting” (“Registering”) message is displayed. Do
not turn off the monitor while the message is displayed. Otherwise, setting information may be lost.

11
Chapter 2 Conguring from the monitor screen
2-3. Setting Network Cameras
●To automatically discover network cameras
Discover network cameras on the network automatically and register them to the system.
This procedure is for setting network cameras connected after performing “Easy Setup” upon initial
startup of the monitor.
Attention
• Only the network cameras installed in the same subnet as the monitor are detected. If a network camera is
installed in a different subnet, the camera must be registered manually (see “To manually register network
cameras” (page 12)).
• When network cameras are not detected by automatic discovery, see “Chapter 4 Troubleshooting” (page
66).
• For information on “Easy Setup”, refer to the Setup Manual.
Procedure
1. Select “Auto Discovery”.
Displays registered
cameras.
1
2. Select “Start” at “Camera Discovery”.
The user authentication screen is displayed.
2
3
5
4
3. Enter the “Username” and “Password” specied in the network camera.
The following values are entered as the default settings:
- Username: “admin”
- Password: “12345”
These are the default settings for Panasonic network cameras. Change the settings if necessary. Please
contact your administrator for the username and password.

12 Chapter 2 Conguring from the monitor screen
4. Select “OK” and press .
Automatic discovery is started and a “Searching” message is displayed.
When the search is completed, the discovered network cameras are added to the list.
5. Select “Apply”.
The setting complete screen is displayed. Select “OK”.
Note
When using a Panasonic network camera
• The settings of the newly detected network camera can be changed.
Select the network camera whose settings you want to change at “Camera Name” and then select “Settings”.
Congure the items on the displayed setting screen. The items that can be congured differ depending on the
camera.
• When registered automatically, the username, password and stream name for accessing the camera are
set to the following values automatically. You can change the settings in “Manual Setting” (see “To manually
register network cameras” (page 12).) Please contact your administrator for your username and password
to access the network camera.
- Username: “admin”
- Password: “12345”
- Stream: “2”
- Channel: “1”
- RS485 PTZ Control: “Off”*1
*1 Only set “RS485 PTZ Control” to “On” when connecting an external device to the network camera
using a RS485 cable.
●To manually register network cameras
Register network cameras manually for cases described below.
• When a network camera is installed in a subnet differing from the subnet of the monitor.
• When settings such as network settings of a registered network camera have been changed.
• When registering a video encoder which supports multiple channels
Procedure
1. Select “Manual Registration”.
A list of network cameras currently registered is displayed.
Registered cameras
are displayed.
1
2
3
2. Select the network camera to congure at “Camera Name”.
When registering a network camera installed in a subnet differing from the subnet of the monitor, select an
available number (with no network camera registered). For a network camera that is already registered,
select the network camera of which to change settings.

13
Chapter 2 Conguring from the monitor screen
3. Select “Settings”.
The network camera setting screen is displayed.
4
5
4. Congure the items.
For setting details, contact your system administrator.
Item Detail Setting range
Camera Name Enter the camera name. When you select
"Execute" for Obtain Camera Name, the camera
automatically obtains the camera name.
• Panasonic network camera: Camera title
• Network camera compatible with the “ONVIF”
protocol: Camera model number, manufacturer
name, etc.
Alphanumeric characters
(up to 24 characters)
IP Address Enter the network camera IP address. 0.0.0.0 to 255.255.255.255
HTTP Port Enter the network camera HTTP port number. 1 to 65535
Protocol Select the protocol for controlling the camera. ONVIF/Panasonic
Stream*1 Set the number of the stream for delivering
camera images. Select a stream supported by the
connected network camera.
1 to 4
Channel*1 Select the channel of the analog encoder. Set to
"1" if the network camera does not support the
channel function.
1 to 4
RS485 PTZ Control Controls the brightness, automatic focus
adjustment, pan, tilt and zoom for devices that are
connected to the camera through a RS485 cable.
On/Off
Username, Password Enter the username and password to use when
accessing network cameras.
Alphanumeric characters
and symbols
(up to 32 characters)
*1 Cannot be set if using a network camera compatible with the “ONVIF” protocol.
5. Select “Apply”.
The setting complete screen is displayed. Select “OK”.
Attention
• If you want to change the set values using the remote control, press the button, then enter the values
(for details see “To enter characters” (page 10)).
• Depending on the network camera type, the “Model No.” displayed on the setting screen may differ from
when the camera is discovered automatically and when it is registered manually.
• Only set “RS485 PTZ Control” to “On” when connecting an external device to the network camera using a
RS485 cable.
Note
• With manual registration, network settings of a camera cannot be changed. When changing the network
settings of a camera, check the network camera’s manual.

14 Chapter 2 Conguring from the monitor screen
●To set network camera functions
Set the network camera functions from the monitor.
Procedure
1. Select “Function Settings”.
Displays current
settings.
1
2
3
2. Select the network camera to congure at “Camera Name”.
3. Select a function.
The setting screen for the selected function is displayed.
Camera Information Display
Select to display or not display the camera information and time of the network camera settings on
the camera images.
Attention
• Cannot be set if using a network camera compatible with the “ONVIF” protocol.
2
1
1. Congure the items.
Item Detail Setting range
Camera Information Display Set whether or not to display camera information. On/Off
Time Display Set whether or not to display the time. 12h/24h/Off
Display Position Set the display position of the camera information
and time.
Upper Left/Upper Right/
Lower Left/Lower Right
2. Select “Apply”.
The setting complete screen is displayed. Select “OK”.

15
Chapter 2 Conguring from the monitor screen
Clock Settings
1. Synchronizes the time of the network camera with the time of the monitor.
Select “Execute” to synchronize the clock.
Video Settings
Set the Image Quality of transmitted images for the network camera.
Note
• This product supports H.264 and MJPEG (ONVIF only) video compression formats.
Attention
• When devices such as recorders are connected to a network camera, the display and recording of such
devices may be affected.
WhenusingaPanasonicnetworkcamera
2
1

16 Chapter 2 Conguring from the monitor screen
1. Congure the items.
Item Detail Setting range
Aspect Ratio Set the H.264 aspect ratio.*1 Camera imaging mode
Resolution Set the H.264 resolution. According to the camera specication
Refresh Interval Set the refresh interval*2 of H.264 images.
0.2s/0.33s/0.5s/1s/2s/3s/4s/5s
Transmission Priority Set the transmission mode of H.264 images. Constant Bit Rate/Frame Rate/Best
Effort
Frame Rate (When the mode is set to “Frame Rate” at
“Transmission Priority”.)
Set the frame rate (image update interval) of
H.264 images.*3
1fps/3fps/5fps/7.5fps/10fps/12fps/
15fps/20fps/30fps
Bit Rate (Max.) Set the maximum H.264 image bit rate. 64kbps/128kbps/256kbps/384kbps/
512kbps/768kbps/1024kbps/
1536kbps/2048kbps/3072kbps/
4096kbps/8192kbps/
Bit Rate (Min.) (When the mode is set to “Best Effort” for
“Transmission Priority”.)
Set the minimum H.264 image bit rate.
64kbps/128kbps/256kbps/384kbps/
512kbps/768kbps/1024kbps/
1536kbps/2048kbps/3072kbps/
4096kbps/8192kbps/
Image Quality (When the mode is set to “Constant Bit Rate”
or “Best Effort” for “Transmission Priority”.)
Set the H.264 image quality.
Low (prioritize motion)/Normal/Fine
(prioritize image quality)
*1 When “1920” is selected for “Resolution”, the aspect ratio is xed to 16:9. The aspect ratio cannot be set
when the network camera “Stream” is set to a value other than “1”.
*2 For H.264 images, the differential data between the full screen frame data and previous frame are sent
periodically. “Refresh Interval” refers to the interval for sending these full screen frame data. Shortening
this interval improves the stability of image quality but also increases the load on the network. “Refresh
Interval” refers to the interval at which the full screen data is transmitted. Shortening this interval improves
the image quality but also increases the load on the network.
*3 The shorter the interval, the shorter the update interval and the smoother the display, but also the larger the
load on the network.
2. Select “Apply”.
The setting complete screen is displayed. Select “OK”.
Attention
• To display the multicast stream of Panasonic network cameras, congure multicast on the camera.
• When you change the “Aspect Ratio”, the camera imaging mode will be changed. Depending on the imaging
mode, the image quality of other recording devices or display devices may be impacted. Check the impact of
changes to the imaging mode before conguring the settings.

17
Chapter 2 Conguring from the monitor screen
ONVIFProleS-compatiblenetworkcameras
2
1
1. Congure the items.
Item Detail Setting range
Media Prole Select the ONVIF image prole. EIZO_Prole/camera prole
Encoder Select the encoder settings of ONVIF images. According to the camera specication
Compression Format Select compression format of ONVIF images. H.264/MJPEG
Resolution Set the resolution of ONVIF images. According to the camera specication
Frame Rate Set the frame rate (image update interval) of
ONVIF images.
1 to 30 fps
Encoding Interval Set the encoder interval of ONVIF images. According to the camera specication
Bit Rate (Max.) Set the maximum ONVIF image bit rate. 0 to 8192 kbps
Video Quality Set the ONVIF image quality. The higher the
value, the higher the image quality.
According to the camera specication
GOV Length*1Set the I-frame interval of ONVIF images. According to the camera specication
H.264 Prole*1Select a H.264 standard prole. Baseline/Main/Extended/High
Transmission Mode Select the transmission format of ONVIF
images.
Unicast/Multicast
Multicast Address*2Set the multicast address for multicast
transmission of ONVIF images.
224.0.0.0 to 239.255.255.255
Multicast Port*2Set the multicast port number for multicast
transmission of ONVIF images.
1024 to 65534 even numbers only
Multicast TTL*2Set the network TTL value for multicast
transmission of ONVIF images.
According to the camera specication
*1 Displays when “H.264” is selected in “Compression Format”.
*2 Displays when “Multicast” is selected in “Transmission Mode”.
2. Select “Apply”.
The setting complete screen is displayed. Select “OK”.
Attention
• Depending on the network camera type, some set values may not be reected. Check the specications of
the camera.
• When changes are made to the image quality settings such as resolution, this may impact on the image
quality of other recording devices and display devices using the same ”Encoder”. Check the impact of
changes to the image quality settings before conguring the settings.

18 Chapter 2 Conguring from the monitor screen
Preset
Preset the shooting position and adjustment status of the network camera.
2
1
3
Displays images of the selected camera.
1. Select the number (1 to 256) to set for “Preset No”.
2. Congure the items.
Item Detail Setting range
Brightness Adjust the network camera brightness. -
Focus Adjust the network camera focus. -
Zoom Adjust the network camera display magnication. -
Position Adjust the network camera shooting position (pan/tilt). -
3. Select “Register (Home)” for registering the selected number as the home position. For all other
registrations, select “Register”.
The setting complete screen is displayed. Select “OK”.
Attention
• Depending on the type of the network camera you are using, some functions may not be available.
• Depending on the network camera type, it may not be possible to register the brightness and focus settings.
Note
• After the setting is registered, the number displayed at “Preset No.” changes from “Not Registered” to “Home”
or “Registered”.
• To clear a setting, select the number to clear at “Preset No.” and then select “Delete”. The data set for the
number is deleted and the number status returns to the unregistered state.

19
Chapter 2 Conguring from the monitor screen
Other
Attention
• Cannot be set if using a network camera compatible with the “ONVIF” protocol.
2
1
1. Congure the items.
Item Detail Setting range
Pan/Tilt-ip Turn on/off the pan/tilt-ip function*1.On/Off
Upside-down*2 Turn on/off the network camera upside down
function.
On/Off
Indicator Turn on/off the network camera Indicator. On/Off
*1 The pan/tilt-ip function reverses the pan/tilt direction automatically at high-speed when the network
camera reaches the movement endpoint. This function allows the user to make pan/tilt operations without
paying attention to movement endpoints.
*2 Check the network camera installation specications before using the upside down function. Depending
on the network camera type, it may not be possible to install the camera upside down even when the
camera supports the upside down function.
2. Select “Apply”.
The setting complete screen is displayed. Select “OK”.
3

20 Chapter 2 Conguring from the monitor screen
2-4. Setting Display Positions of Camera Images
Set the display position for images from the network camera.
Procedure
1. Select “Position”.
Indicates the
display positions
on the monitor
screen.
1
2
3
2. Congure the items.
Item Detail Setting range
Position Select a position to display a camera image.
Set the network camera to the number of the
desired position for display.
-
Camera Name Display Select to display or not display the camera name
and time set on the monitor. (The camera name is
displayed on the upper left of the image.)
On/Off
Sequence Interval Set the interval for changing over the screen during
sequential display.
5s to 60s
Aspect Ratio Mode Set which aspect ratio to apply when the aspect
ratio of the video delivered from the network
camera and the aspect ratio of the monitor image
display area differ.
Full/Aspect
3. Select “Apply”.
The setting complete screen is displayed. Select “OK”.
Attention
• All registered network cameras must be congured. A network camera can only be set for one display position.
When there are incorrect settings, “Apply” cannot be selected.
Note
• If it takes a while for images to be displayed during sequential display, set a higher value for “Sequence Interval”.