Eizo DuraVision FDX1003 User manual

Important
Please read this User’s Manual, and the Setup Manual (separate
volume) carefully to familiarize yourself with safe and effective usage.
• Please refer to the Setup Manual for basic information ranging from
monitor installation to using the monitor.
• The latest User’s Manual is available for download from our web site:
http://www.eizoglobal.com
User’s Manual
Color LCD Monitor
Touch Panel Color LCD Monitor

2
This product has been adjusted specically for use in the region to which it was originally shipped. If
operated outside this region, the product may not perform as stated in the specications.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by
any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
EIZO Corporation is under no obligation to hold any submitted material or information condential unless
prior arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every
effort has been made to ensure that this manual provides up-to-date information, please note that EIZO
monitor specications are subject to change without notice.

3
CONTENTS
CONTENTS
CONTENTS............................................................. 3
Chapter 1 Introduction....................................... 4
1-1. Features ......................................................... 4
1-2. EIZO LCD Utility Disk.................................... 5
●Disk contents and software overview ............. 5
●To use touch panel driver ............................... 5
1-3. Basic Operations and Functions ................ 6
●Basic operation of the Setting menu ............... 6
●Functions ......................................................... 7
Chapter 2 Adjusting Screens ............................ 8
2-1. Setting the Resolution ................................. 8
●Display resolution ............................................ 8
●Setting resolution ............................................ 8
2-2. Adjusting Color ............................................. 9
●To select the display mode (Color Mode) ........ 9
●To perform advanced adjustments ................. 9
●Adjustable settings in each mode ..................10
●To adjust brightness .......................................10
●To adjust color temperature ...........................11
●To adjust the color saturation .........................11
●To adjust hue ..................................................12
●To adjust gain .................................................12
2-3. Screen Adjustment ......................................13
●Digital Signal Input .........................................13
●Analog Signal Input ........................................13
Chapter 3 Setting Monitor ............................... 17
3-1. Setting the Orientation................................17
3-2. Enabling / Disabling DDC/CI
communication ...........................................17
3-3. Locking Operation Buttons ........................17
3-4. Showing and hiding the EIZO logo ............17
3-5. Setting Language.........................................18
3-6. Resetting the Monitor to the Default
Settings.........................................................18
●To reset the color adjustments .......................18
●To reset all adjustments to the default
settings ...........................................................18
Chapter 4 Power Saving Functions ................ 19
4-1. Setting Power Saving ..................................19
4-2. Setting Power Indicator...............................19
4-3. Enabling / Disabling Auto Power-OFF...... 20
Chapter 5 Troubleshooting.............................. 21
5-1. No picture .....................................................21
5-2. Imaging problems (for both digital and
analog).......................................................... 22
5-3. Imaging problems (for analog only) ......... 22
5-4. Other problems ........................................... 23
5-5. Touch panel problems (for FDX1003T /
FDX1203T only)............................................ 23
Chapter 6 Reference ........................................ 24
6-1. Connecting Multiple PCs ........................... 24
●To switch among input signals .......................24
●To set input signal selection .......................... 25
6-2. Displaying Monitor Information ................ 25
6-3. Preset Timing .............................................. 26
Chapter 7 Glossary .......................................... 27
Appendix.............................................................. 29
Trademark ............................................................... 29
License / Copyright................................................ 29
LIMITED WARRANTY............................................. 30
Recycling Information ........................................... 39

4Chapter 1 Introduction
Chapter 1 Introduction
Thank you very much for choosing an EIZO color LCD monitor.
1-1. Features
• FDX1003 / FDX1003T : 10.4″ LCD, FDX1203 / FDX1203T : 12.1″ LCD
• Supports a resolution of 1024 × 768
• LED backlight LCD panel
The LED backlight provides better power efciency and reduced power consumption compared to existing
uorescent backlight LCD panels. No mercury, a hazardous substance, is used.
• Power saving function
Suppressing the power consumption reduces the carbon dioxide emissions. This product is equipped with
power saving function.
- Eco Timer
This function allows you to set the monitor to turn off automatically after a specied time has passed in the
power saving mode.
See “4-3. Enabling / Disabling Auto Power-OFF” (page 20).
• Displays HDCP (High-bandwidth Digital Protection) protected contents
(for FDX1003T / FDX1203T only)
• Touch Panel provided
- Detection method: Analog resistive technology
- Supported OS: Microsoft Windows 7 Service Pack 1 (32 bit/64 bit)
Microsoft Windows Vista Service Pack 2 (32 bit)
Microsoft Windows XP Service Pack 3 (32 bit)
- Communication: USB, RS-232C (* Cannot be used at the same time.)

5
Chapter 1 Introduction
1-2. EIZO LCD Utility Disk
An “EIZO LCD Utility Disk” (CD-ROM) is supplied with this product. The following table shows the disk
contents and the overview of the software programs.
●Disk contents and software overview
The disk includes adjustment software, touch panel software, and user’s manuals. Refer to Readme.
txt le on the disk for software startup procedures or le access procedures.
Item Overview Windows Macintosh
Screen adjustment pattern les Used when adjusting the image of analog
signal input manually. √ √
Touch panel driver*1 Driver software required for operating the
touch panel monitor on Windows. √ -
User’s Manual of this monitor (PDF le) √ √
User’s Manual for Touch Panel Driver (PDF le)*1 √ -
Readme.txt le √ √
*1 Used only for the FDX1003T / FDX1203T.
●To use touch panel driver
For information on how to install or use the touch panel driver, see the Touch Panel Driver User’s
Manual (on the CD-ROM).

6Chapter 1 Introduction
1-3. Basic Operations and Functions
●Basic operation of the Setting menu
1. Displaying the Setting menu
1. Press . The Setting menu appears.
2.
Adjusting / Setting
1. Choose a menu to adjust / set with , , and then press . The Sub menu appears.
2. Choose an item to adjust / set with , , and then press . The adjustment / setting menu
appears.
3. Adjust / set the selected item with , , and then press .
3.
Exiting
1. Choose “Return” from the Sub menu and press . The Setting menu appears.
2. Choose “Exit” from the Main menu and press . The Setting menu quits.
Note
• The Setting menu can also be exited by pressing twice quickly.

7
Chapter 1 Introduction
●Functions
The following table shows the Setting menu and setting items of each menu.
Main menu Setting Reference
Color*1 Brightness “2-2. Adjusting Color” (page 9)
Temperature
Advanced Settings Saturation
Hue
Gain
Color Reset “To reset the color adjustments” (page 18)
Screen Smoothing “2-3. Screen Adjustment” (page 13)
Analog Adjustment*2 Auto Screen Adjust
Auto Range Adjust
Clock
Phase
Hor.Position
Ver.Position
PowerManager Power Save “4-1. Setting Power Saving” (page 19)
Eco Timer “4-3. Enabling / Disabling Auto Power-OFF”
(page 20)
Monitor Settings Input Signal “To set input signal selection” (page 25)
Power Indicator “4-2. Setting Power Indicator” (page 19)
Language “3-5. Setting Language” (page 18)
DDC/CI “3-2. Enabling / Disabling DDC/CI
communication” (page 17)
Logo “3-4. Showing and hiding the EIZO logo”
(page 17)
Reset “To reset all adjustments to the default
settings” (page 18)
Information “6-2. Displaying Monitor Information” (page
25)
*1 The adjustment / settings available on the “Color” menu depend on the selected Color mode (see
“Adjustable settings in each mode” (page 10)).
*2 These functions can be adjusted with analog input.

8Chapter 2 Adjusting Screens
Chapter 2 Adjusting Screens
2-1. Setting the Resolution
●Display resolution
For details on compatible resolutions, refer to “Compatible Resolutions” in the Setup Manual.
●Setting resolution
When you connect the monitor to the PC and nd that the resolution is improper, or when you want to
change the resolution, follow the procedure below.
Windows 7
1. Right-click the mouse anywhere on the desktop except for icons.
2. From the displayed menu, click “Screen resolution”.
3. On the “Screen Resolution” dialog box, select the monitor.
4. Click “Resolution” to select the desired resolution.
5. Click the “OK” button.
6. When a conrmation dialog box is displayed, click “Keep changes”.
Windows Vista
1. Right-click the mouse anywhere on the desktop except for icons.
2. From the displayed menu, click “Personalize”.
3. On the “Personalization” window, click “Display Settings”.
4. On the “Display Settings” dialog box, select the “Monitor” tab and select desired resolution in the
“Resolution” eld.
5. Click the “OK” button.
6. When a conrmation dialog box is displayed, click “Yes”.
Windows XP
1. Right-click the mouse anywhere on the desktop except for icons.
2. From the displayed menu, click “Properties”.
3. When the “Display Properties” dialog box is displayed, click the “Settings” tab and select desired
resolution for “Screen resolution” under “Display”.
4. Click the “OK” button to close the dialog box.
Mac OS X
1. Select “System Preferences” from the Apple menu.
2. When the “System Preferences” dialog box is displayed, click “Displays” for “Hardware”.
3. On the displayed dialog box, select the “Display” tab and select desired resolution in the
“Resolutions” eld.
4. Your selection will be reected immediately. When you are satised with the selected resolution,
close the window.

9
Chapter 2 Adjusting Screens
2-2. Adjusting Color
●To select the display mode (Color Mode)
This function allows easy selection of a desired mode according to monitor application.
Display Modes
Mode Purpose
User1 Select this to dene a desired set of parameter settings.
User2
sRGB Suitable for color matching with sRGB compatible peripherals.
The mode menu
appears.
Procedure
1. Press .
The mode menu appears at the bottom left of the screen.
2. The mode among the list is highlighted in turn each time is pressed.
You can switch the mode with or while the mode menu is displayed.
User1←→User2←→sRGB
Note
• The Setting menu and the Mode menu cannot be displayed at the same time.
●To perform advanced adjustments
The “Color” menu of the Setting menu allows you to set and save the independent color adjustment
for each mode.
Attention
• It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more
after the monitor power has been turned on, and then adjust the monitor.
• Perform the range adjustment rst when adjusting color for analog signals (see “To adjust color gradation
automatically” (page 16)).
• The same image may be seen in different colors on multiple monitors due to their monitor-specic
characteristics. Make ne color adjustment visually when matching colors on multiple monitors.

10 Chapter 2 Adjusting Screens
●Adjustable settings in each mode
The adjustable settings depend on the mode. (Non-adjustable or non-settable function cannot be
selected.)
√: Adjustable -: Not adjustable
Function Color Mode
User1 User2 sRGB
Brightness √√√
Temperature √ √ -
Advanced Settings Saturation √ √ -
Hue √ √ -
Gain √ √ -
Color Reset √√√
●To adjust brightness
The screen brightness is adjusted by changing the brightness of the backlight (light source from the
LCD back panel).
Adjustable range
0 to 100
Procedure
1. Press .
The brightness adjustment screen appears.
2. Use or for adjustment.
3. Press to exit.
Attention
• A range of setting values on the adjustment screen are displayed in magenta. The contrast (video signal level)
is changed to adjust the brightness in this range.
Note
• Alternatively, you can use “Brightness” under “Color” in the Adjustment menu to adjust it.

11
Chapter 2 Adjusting Screens
●To adjust color temperature
Color temperature can be adjusted.
The color temperature is normally used to express the hue of “White” and / or “Black” by a numerical
value. The value is expressed in degrees “K” (Kelvin).
The screen becomes reddish at a low color temperature, and bluish at a high color temperature, like
the ame temperature. A gain preset value is set for each color temperature setting value.
Adjustable range
Off, Mode1 (Approx. 6500 K), Mode2 (Approx. 8000 K), Mode3 (Approx. 9300 K)
Procedure
1. Choose “Color” in the Setting menu, and press .
2. Choose “Temperature” in the “Color” menu, and press .
The “Temperature” menu appears.
3. Use or for adjustment.
4. Press to exit.
Note
• “Gain” allows you to perform more advanced adjustment (see “To adjust gain” (page 12)).
• If you set to “Off”, the image is displayed in the preset color of the monitor (Gain: 100 for each RGB).
• When gain is changed, the color temperature is changed to “Off”.
●To adjust the color saturation
This function allows you to adjust color saturation.
Adjustable range
-50 to 50
Procedure
1. Choose “Color” in the Setting menu, and press .
2. Choose “Advanced Settings” in the “Color” menu, and press .
3. Choose “Saturation” in the “Advanced Settings” menu, and press .
The “Saturation” menu appears.
4. Use or for adjustment.
5. Press to exit.
Attention
• Using this function may make some color gradations unavailable for display.
Note
• The minimum value (-50) changes the screen to monochrome.

12 Chapter 2 Adjusting Screens
●To adjust hue
This function allows you to adjust hue.
Adjustable range
-50 to 50
Procedure
1. Choose “Color” in the Setting menu, and press .
2. Choose “Advanced Settings” in the “Color” menu, and press .
3. Choose “Hue” in the “Advanced Settings” menu, and press .
The “Hue” menu appears.
4. Use or for adjustment.
5. Press to exit.
Attention
• Using this function may make some color gradations unavailable for display.
●To adjust gain
The brightness of each color component red, green, and blue is called “Gain”. You can change the
hue of “white” by adjusting gain.
Adjustable range
0 to 100
Procedure
1. Choose “Color” in the Setting menu, and press .
2. Choose “Advanced Settings” in the “Color” menu, and press .
3. Choose “Gain” in the “Advanced Settings” menu, and press .
The “Gain” menu appears.
4. Adjust gain with or for each of red, green, and blue.
5. Press to exit.
Attention
• Using this function may make some color gradations unavailable for display.
Note
• The value of gain changes with that of color temperature.
• When gain is changed, the color temperature is changed to “Off”.

13
Chapter 2 Adjusting Screens
2-3. Screen Adjustment
●Digital Signal Input
When digital signals are input, images are displayed correctly based on the preset data of the
monitor, but if characters and / or lines appear blurred, go to “To modify blurred characters / lines”
(page 16).
When performing more advanced adjustment, see “2-2. Adjusting Color” (page 9) and subsequent
pages.
●Analog Signal Input
Attention
• It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more
after the monitor power has been turned on, and then adjust the monitor.
• The Self Adjust (automatic screen adjustment) function does not work for the images under the resolution of
800 × 600 (SVGA).
• The self adjustment (or automatic screen adjustment) function works correctly when an image is fully
displayed over the Windows or Macintosh display area. They do not work properly in the cases below:
- When an image is displayed only on a part of the screen (command prompt window, for example)
- When a black background (wallpaper, etc.) is in use
Also, these functions cannot work properly in some graphic boards.
The monitor screen adjustment is used to suppress ickering of the screen or adjust screen position
and screen size correctly according to the PC to be used.
Note
• The Self Adjust function works when all of the following conditions are satised:
- When a signal is input into the monitor for the rst time or when a resolution or vertical / horizontal scan
frequency not used before is set
If the screen is not displayed correctly even after performing the Self Adjust operation, adjust the
screen according to the procedures on the following pages to use the monitor comfortably.
Setting Procedures
1. Perform the auto adjustment.
●To adjust ickering, screen position, and screen size automatically
Procedure
1. Choose “Screen” in the Setting menu, and press .
2. Choose “Analog Adjustment” in the “Screen” menu, and press .
3. Choose “Auto Screen Adjust” in the “Analog Adjustment” menu, and press .
4. Select “Yes” with or , and press .
Flickering, screen position, and screen size are corrected by the auto-adjustment function.
If the screen is not displayed correctly even after performing the auto adjustment, perform adjustments
according to the following procedure. If the screen is displayed correctly, go to “5. Adjusting color gradation.”
(page 16).

14 Chapter 2 Adjusting Screens
2.
Prepare to use analog screen adjustment patterns.
Load the “EIZO LCD Utility Disk” to your PC, and then open the “Screen adjustment pattern les”.
Note
• For details and instructions on opening the “Screen adjustment pattern les”, refer to the Readme.txt le.
3.
Perform the auto adjustment again with the analog screen adjustment pattern
displayed.
●To adjust ickering, screen position, and screen size automatically
Procedure
1. Display Pattern 1 in full screen on the monitor using the “Screen adjustment pattern les”.
2. Choose “Screen” in the Setting menu, and press .
3. Choose “Analog Adjustment” in the “Screen” menu, and press .
4. Choose “Auto Screen Adjust” in the “Analog Adjustment” menu, and press .
5. Select “Yes” with or , and press .
Flickering, screen position, and screen size are corrected by the auto-adjustment function.
If the screen is not displayed correctly even after performing the auto adjustment, perform adjustments
according to the following procedure. If the screen is displayed correctly, go to “5. Adjusting color gradation.”
(page 16).
4.
Choose “Screen” from the Setting menu to perform advanced adjustments.
Adjust the clock, phase and position, in this order.
●To eliminate vertical bars
Procedure
1. Choose “Analog Adjustment” in the “Screen” menu, and press .
2. Choose “Clock” in the “Analog Adjustment” menu, and press .
The “Clock” menu appears.
3. Adjust the clock with or to eliminate vertical bars.
Press or slowly so as not to miss the adjustment point.
4. Press to exit.
When blurring, ickering or bars appear on the screen after adjustment, proceed to “To remove ickering or
blurring ”.

15
Chapter 2 Adjusting Screens
●To remove ickering or blurring
Procedure
1. Choose “Analog Adjustment” in the “Screen” menu, and press .
2. Choose “Phase” in the “Analog Adjustment” menu, and press .
The “Phase” menu appears.
3. Adjust the phase with or to minimize ickering or blurring.
4. Press to exit.
When vertical bars appear on the screen after adjustment, go back to “To eliminate vertical bars ”.
(Clock → Phase → Position)
Attention
• Flickering or blurring may not be eliminated depending on your PC or graphics board.
●To correct the screen position
Note
• Since the number of pixels and the pixel positions are xed on the LCD monitor, only one position is provided
to display images correctly. The position adjustment is made to shift an image to the correct position.
Procedure
1. Choose “Analog Adjustment” in the “Screen” menu, and press .
2. Choose “Hor.Position” or “Ver.Position” from the “Analog Adjustment” menu, and press .
The “Hor. Position” or “Ver. Position” menu appears.
3. Adjust the position with or .
4. Press to exit.
5. Close Pattern 1.

16 Chapter 2 Adjusting Screens
5.
Adjusting color gradation.
●To adjust color gradation automatically
Every color gradation (0 to 255) can be displayed by adjusting the signal output level.
Procedure
1. Display Pattern 2 in full screen on the monitor using the “Screen adjustment pattern les”.
2. Choose “Screen” in the Setting menu, and press .
3. Choose “Analog Adjustment” in the “Screen” menu, and press .
4. Choose “Auto Range Adjust” in the “Analog Adjustment” menu, and press .
5. Select “Yes” with or , and press .
The output range is set automatically.
6. Close Pattern 2.
6.
Modify blurred characters or lines.
●To modify blurred characters / lines
When an image is displayed with a resolution other than recommended, the characters or lines of
the displayed image may blur.
Attention
• Smoothing setting may not be required depending on the display resolution. (You cannot choose the
smoothing icon.)
Adjustable range
1 to 5
Procedure
1. Choose “Screen” in the Setting menu, and press .
2. Choose “Smoothing” in the “Screen” menu, and press .
The “Smoothing” menu appears.
3. Use or for adjustment.
4. Press to exit.

17
Chapter 3 Setting Monitor
Chapter 3 Setting Monitor
3-1. Setting the Orientation
The image can be ipped vertically (rotated 180 degrees) to match the orientation of the monitor.
Procedure
1. Press to turn off the monitor.
2. Hold down while pressing to turn on the monitor.
The image is ipped vertically each time this operation is performed.
3-2. Enabling / Disabling DDC/CI communication
This function allows you to enable / disable the DDC/CI communication (see “Chapter 7 Glossary” (page
27)).
Procedure
1. Choose “Monitor Settings” in the Setting menu, and press .
2. Choose “DDC/CI” in the “Monitor Settings” menu, and press .
The “DDC/CI” menu appears.
3. Select “On” or “Off” with or .
4. Press to exit.
3-3. Locking Operation Buttons
This function allows you to lock the settings to prevent them being changed.
Procedure
1. Press to turn off the monitor.
2. Hold down while pressing to turn on the monitor.
You can toggle between Lock and Unlock by performing steps 1 and 2.
Note
• The following operations are available even if the buttons are locked:
- Turning on or off the monitor with the Power button
3-4. Showing and hiding the EIZO logo
When the monitor is turned on, the EIZO logo appears on the screen. You can choose to show or hide
the display of the EIZO logo.
Procedure
1. Choose “Monitor Settings” in the Setting menu, and press .
2. Choose “Menu Settings” in the “Monitor Settings” menu, and press .
3. Choose “Logo” in the “Menu Settings” menu, and press .
The “Logo” menu appears.
4. Select “On” or “Off” with or .
5. Press to exit.

18 Chapter 3 Setting Monitor
3-5. Setting Language
This function allows you to select a language for the Setting menu or messages.
Selectable languages
English, German, French, Spanish, Italian, Swedish, Japanese, Simplied Chinese, Traditional
Chinese
Procedure
1. Choose “Monitor Settings” in the Setting menu, and press .
2. Choose “Language” in the “Monitor Settings” menu, and press .
The “Language” menu appears.
3. Choose a language with or .
4. Press to exit.
3-6. Resetting the Monitor to the Default Settings
The setting values are reset to the default settings.
Attention
• After resetting, you cannot undo the operation.
Note
• Regarding the default setting, see “Compatible Resolutions” in the Setup Manual.
●To reset the color adjustments
This function only resets the color adjustments for the currently selected mode to the default settings.
Procedure
1. Choose “Color” in the Setting menu, and press .
2. Choose “Color Reset” in the “Color” menu, and press .
3. Select “Yes” with or .
4. Press .
The color adjustments revert to the default settings.
●To reset all adjustments to the default settings
This function resets all adjustments to the default settings.
Procedure
1. Choose “Monitor Settings” in the Setting menu, and press .
2. Choose “Reset” in the “Monitor Settings” menu, and press .
3. Select “Yes” with or .
4. Press .
All adjustments revert to the default settings.

19
Chapter 4 Power Saving Functions
Chapter 4 Power Saving Functions
4-1. Setting Power Saving
This function allows you to set the monitor into the power saving mode according to the PC status. When
the monitor has shifted to the power saving mode, the images on the screen are not displayed.
Attention
• Unplugging the power cord completely shuts off power supply to the monitor.
Note
• The monitor changes to the power saving mode about 15 seconds after the signal input ceases to be detected.
Procedure
1. Choose “PowerManager” in the Setting menu, and press .
2. Choose “Power Save” in the “PowerManager” menu, and press .
The “Power Save” menu appears.
3. Select “On” or “Off” with or .
4. Press to exit.
Power Saving System
Analog Signal Input
This monitor complies with the VESA DPM standard.
PC Monitor Power Indicator
On Operating Blue
Power saving
mode
STAND-BY
SUSPENDED
OFF
Power saving mode Orange
Power Off Power saving mode Orange
Digital Signal Input
This monitor complies with the DVI DMPM standard.
PC Monitor Power Indicator
On Operating Blue
Power saving mode Power saving mode Orange
Power Off Power saving mode Orange
Exiting the power saving mode
If the monitor receives input, it automatically exits the power saving mode and returns to the normal
display mode.
4-2. Setting Power Indicator
This function allows you to set the power indicator (blue) ON / OFF in the monitor ON condition.
Procedure
1. Choose “Monitor Settings” in the Setting menu, and press .
2. Choose “Power Indicator” in the “Monitor Settings” menu, and press .
The “Power Indicator” menu appears.
3. Select “On” or “Off” with or .
4. Press to exit.

20 Chapter 4 Power Saving Functions
4-3. Enabling / Disabling Auto Power-OFF
This function allows you to switch the setting to turn off the monitor automatically after a specied time
has passed in the power saving mode.
Adjustable range
Off, 0, 1, 2, 3, 5, 10, 15, 20, 25, 30, 45 min, 1, 2, 3, 4, 5 h
Procedure
1. Choose “PowerManager” in the Setting menu, and press .
2. Choose “Eco Timer” in the “PowerManager”, and press .
3. Select “Off” or time to turn off the monitor with or .
4. Press to exit.