Eizo FORIS FS2434 User manual

Important
Please read PRECAUTIONS, this User’s Manual, and the Setup Guide
(separate volume) carefully to familiarize yourself with safe and
effective usage.
• Please refer to the Setup Guide for basic information ranging from
connection of the monitor to a PC or external device to using the
monitor.
• The latest User’s Manual is available for download from our web site:
http://www.eizo.com
User’s Manual
Color LCD Monitor

2
Location of Caution Statement
<For USA-California Only>
CR Coin Lithium Battery contains Perchlorate Material - special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate.
This product has been adjusted specically for use in the region to which it was originally shipped. If
operated outside this region, the product may not perform as stated in the specications.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by
any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
EIZO Corporation is under no obligation to hold any submitted material or information condential unless
prior arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every
effort has been made to ensure that this manual provides up-to-date information, please note that EIZO
monitor specications are subject to change without notice.

3
Notice for this monitor
Notice for this monitor
This product is suited to purposes like displaying video games and viewing multimedia content.
This product has been adjusted specically for use in the region to which it was originally shipped. If the
product is used outside the region, it may not operate as specied in the specications.
This product may not be covered by warranty for uses other than those described in this manual.
The specications noted in this manual are only applicable when the following are used:
· Power cords provided with the product
· Signal cables specied by us
Only use optional products manufactured or specied by us with this product.
It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more
after the monitor power has been turned on, and then adjust the monitor.
Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term use and
maintain a stable display.
When the screen image is changed after displaying the same image for extended periods of time, an
afterimage may appear. Use the screen saver or power save function to avoid displaying the same image for
extended periods of time.
If the monitor displays continuously over a long period of time, dark smudges or burn-in may appear. To
maximize the life of the monitor, we recommend the monitor be turned off periodically.
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (refer
to “Cleaning” (page 4)).
The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit pixels may
appear on the LCD panel, this is not a malfunction. Percentage of effective dots: 99.9994% or higher.
The backlight of the LCD panel has a xed lifetime. When the screen becomes dark or begins to icker,
please contact your EIZO representative.
Do not press on the panel or edge of the frame strongly, as this may result in display malfunctions, such
as interference patterns, etc. If pressure is continually applied to the panel, it may deteriorate or damage
your panel. (If the pressure marks remain on the panel, leave the monitor with a black or white screen. The
symptom may disappear.)
Do not scratch or press on the panel with any sharp objects, as this may result in damage to the panel. Do
not attempt to brush with tissues as this may scratch the panel.
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew
condensation may occur on the interior and exterior surfaces of the monitor. In that case, do not turn the
monitor on. Instead wait until the dew condensation disappears, otherwise it may cause some damage to the
monitor.

4Notice for this monitor
Cleaning
Attention
• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet
or panel, and also quality deterioration of the image.
• Never use any thinner, benzene, wax, and abrasive cleaner, which may damage the cabinet or panel.
Note
• The optional ScreenCleaner is recommended for cleaning the cabinet and panel surface.
If necessary, the stains on the cabinet and panel surface can be removed by moistening part of a soft
cloth with water.
To use the monitor comfortably
• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor
according to the environmental conditions.
• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.

5
CONTENTS
CONTENTS
Notice for this monitor ......................................... 3
Cleaning .................................................................... 4
To use the monitor comfortably............................. 4
CONTENTS............................................................. 5
Chapter 1 Introduction....................................... 7
1-1. Features ......................................................... 7
1-2. Controls and Functions ............................... 8
●Front ................................................................ 8
●Rear................................................................. 9
●Before Using Remote Control ........................11
1-3. Basic Operations and Functions ...............12
●Basic operation of the Setting menu..............12
●Functions........................................................13
Chapter 2 Adjusting Screens .......................... 14
2-1. Compatible Resolutions/Formats..............14
●DVI-D Input and HDMI Input (PC signal).......14
●HDMI Input (video signal)...............................14
2-2. Setting the Resolution ................................15
2-3. Adjusting Color ............................................16
●To select the display mode (Color Mode).......16
●To perform advanced adjustments ................17
●Adjustable settings in each mode ..................17
●To adjust brightness .......................................18
●Adjusting the brightness and color of
black “Black Level” .........................................18
●To adjust contrast...........................................18
●To adjust the color saturation.........................19
●To adjust hue..................................................19
●To adjust color temperature .......................... 20
●To adjust gamma........................................... 20
●To adjust gain .................................................21
●To reduce noise..............................................21
●To set the enhancement ratio of
ContrastEnhancer ......................................... 22
●To set overdrive intensity .............................. 22
2-4. Setting the Color Space for the HDMI
input signal.................................................. 23
2-5. Screen Size Changing ................................ 24
●DVI-D Input and HDMI Input (PC signal).......24
●HDMI Input (video signal).............................. 25
●To modify blurred characters/lines................ 26
Chapter 3 Setting Monitor ............................... 27
3-1. Switching sound source for
HDMI signal input ....................................... 27
3-2. Adjusting Volume........................................ 27
●To turn the volume up/down.......................... 27
●To mute the sound temporarily...................... 28
3-3. To adjust the sound level ........................... 28
3-4. Locking Operation Buttons ....................... 29
3-5. Showing and hiding the EIZO logo ........... 29
3-6. Setting Language........................................ 29
3-7. Changing the authentication method for
HDMI signal input........................................ 30
3-8. Resetting the Monitor to the Default
Settings........................................................ 30
●To reset the color adjustments...................... 30
●To reset all adjustments to the default
settings...........................................................31
Chapter 4 Using Smart Function .................... 32
4-1. Setting “Smart Detection”......................... 32
4-2. Setting “Smart Resolution”....................... 33
4-3. Setting “Smart Insight 2”........................... 34
4-4. Checking the setting status....................... 34
Chapter 5 Power Saving Functions ................ 35
5-1. Setting Power Saving ................................. 35
●Monitor .......................................................... 35
●To change the exiting method from the
power saving mode ....................................... 36
●Audio Output ................................................. 36
●USB ................................................................37
5-2. Setting Power Indicator...............................37
5-3. Enabling/Disabling Automatic
Brightness Adjustment “Auto EcoView” ..37
5-4. Reducing Glare “EcoView Optimizer”...... 38
5-5. Checking the power saving level .............. 38
5-6. Enabling/Disabling Auto Power-OFF
“Off Timer” .................................................. 39
Chapter 6 Connecting Cables ......................... 40
6-1. Connecting Multiple External Devices..... 40
●To switch among input signals ...................... 40
6-2. Connecting External Speaker ....................41
Chapter 7 Troubleshooting.............................. 42
7-1. No picture .................................................... 42
7-2. Imaging problems....................................... 43
7-3. Other problems ........................................... 44
Chapter 8 Reference ........................................ 46
8-1. How to Attach the Optional Arm ............... 46
8-2. Detaching/Attaching Stand Base.............. 48
8-3. Attaching/Detaching Cable Holder........... 50

6CONTENTS
8-4. Making Use of USB
(Universal Serial Bus)..................................51
●Required System Environment ......................51
●Connection procedure
(Setup of USB function)..................................51
8-5. Displaying Monitor Information ................ 52
8-6. Specications ............................................. 53
Chapter 9 Glossary .......................................... 56
Appendix.............................................................. 58
Trademark ............................................................... 58
License / Copyright................................................ 58
ENERGY STAR........................................................ 59
FCC Declaration of Conformity ............................ 60
Hinweise zur Auswahl des richtigen
Schwenkarms für Ihren Monitor............................61
Hinweis zur Ergonomie : ........................................61
LIMITED WARRANTY............................................. 62
Recycling Information ............................................71
China Measures for RoHS Compliance in
ChinaRoHS...............................................................75

7
Chapter 1 Introduction
Chapter 1 Introduction
Thank you very much for choosing an EIZO color LCD monitor.
1-1. Features
• 23.8″ wide format LCD
• Supports a resolution of 1920 × 1080
• Panel with a wide eld of view adopted
IPS panel with 178 º horizontal and vertical viewing angles.
• HDMI connector × 2
Applicable to the PC input signal using HDMI input, allowing three different digital signal inputs from a PC.
• The Color Mode function allows the user to select the display mode optimum to the displayed
image.
See “To select the display mode (Color Mode)” (page 16).
• EIZO’s unique “Smart” technology
- Smart Detection function
This function allows the user to change the area on the screen to which the Smart Resolution or Smart
Insight 2 function is applied (only animated images or whole screen).
- Smart Resolution function
This function adjusts the perceived resolution of the images so that the blurs are reduced and images are
displayed vividly and clearly.
In addition, you can correct the color of skin and text affected by the “Smart Resolution” settings.
- Smart Insight 2 function
This function analyzes the image and corrects the brightness for each pixel to make dark area of
images visible. It also increases the color saturation.
See “Chapter 4 Using Smart Function” (page 32).
• Input lag is less than 0.05 frames.
Mouse movements and keyboard inputs are instantaneously reected on the screen.
• Adopts EyeCare dimming
Suppresses icker when the LED backlight intensity is reduced.
• Equipped with a USB 3.0 hub function.
Supports high-speed data transfers of up to 5 Gbps. Massive data can be transferred in a short time, e.g.
when using a USB storage device.
• Thin bezel
The thin bezel does not interfere with the movement of the line of sight when using multiple monitors.
• Stand with wide range of movement
The monitor can be adjusted to a position where it provides you with a comfortable and less tiring work
environment.
(Tilt: 25 ° up / 0 ° down, Swivel: 344°, Adjustable height: 60 mm (2.36 inch))
• Remote control enables easy operation, setting and adjustment of the monitor.
See “1-2. Controls and Functions” (page 8).
• Built-in stereo speakers and headphone jack
See “1-2. Controls and Functions” (page 8).
• Line output connector
A speaker with built-in amplier can be connected to the monitor to output sound.
See “6-2. Connecting External Speaker” (page 41).
• Displays HDCP (High-bandwidth Digital Protection) protected content.
• Supports the “G-Ignition” software which allows for screen adjustment via mouse or keyboard.
Can be downloaded from our website (http://www.eizo.com).

8Chapter 1 Introduction
1-2. Controls and Functions
●Front
7
1 32 4 5 6
Setting menu*1
1. Auto EcoView sensor Detects ambient brightness (Auto EcoView function (page 37), EcoView Optimizer
function (page 38)).
2. button Switches input signals for display (page 40).
PC (DVI) → HDMI1 → HDMI2
3. / button Displays the volume adjustment menu to volume up or down.
4. button Turns the power on or off.
5. Power indicator
Indicates the monitor’s operation status.
White: Operating
Orange: Power saving mode
Red: Power off
OFF: Main power off
6. Remote control
detector Receives the signal from the remote control.
7. Speaker Outputs audio source.
*1 See “Basic operation of the Setting menu” (page 12) for how to use.

9
Chapter 1 Introduction
●Rear
17 18
10
15
16
8 9
13
12
11
14
19
8. Main power switch Turns the main power on or off.
9. Power connector Connects the power cord.
10. Input signal connector
(Left: HDMI connector (HDMI1) / Center: HDMI connector (HDMI2) /
Right: DVI-D connector)
Connects external devices such as a PC.
11. USB downstream port Connects a peripheral USB device.
12. USB upstream port Connects the USB cable to use software that needs a USB connection, or to use the
USB hub function (page 51).
13. Line output connector (Stereo mini jack)
Connects a speaker with built-in amplier (page 41).
14. Line input connector (Stereo mini jack)
Connects external devices such as a PC.
15. Headphone jack Connects the headphones.
16. Handle
Handle used for transportation
Attention
• Firmly grasp and hold the monitor by the bottom while grabbing the handle, and
carefully convey the monitor so as not to drop it.
17. Security lock slot Complies with Kensington’s MicroSaver security system.
18. Stand*2 Adjusts the height and angle (tilt and swivel) of the monitor.
19. Cable holder Covers the monitor cables.
*2 An optional arm (or an optional stand) can be attached by removing the stand (see “8-1. How to Attach the
Optional Arm” (page 46)).

10 Chapter 1 Introduction
Remote Control
1. PC Switches to PC signal input.
2. HDMI
Switches to HDMI signal input.
Each time you press , the system toggles between
HDMI1 and HDMI2.
3. MODE Changes the color mode.
4. MENU Displays/Exits the Setting menu.
5. EcoView Displays/Exits “EcoView Menu”.
6. SIZE Changes the screen size.
7. Smart Displays/Exits the “Smart Functions” menu.
8. POWER Turns the power on or off.
9. OFF TIMER Sets the time until the monitor power-off.
10. / / /
• Provides the menu selection as well as the adjustment
and setting of a function.
• / : Displays the brightness adjustment menu
(page 18).
11. ENTER Determines an item on the menu screen, and saves
values adjusted.
12. RETURN Returns to the previous menu in menu operation.
13. VOLUME +/- Adjusts the volume.
14. MUTE Mutes sound temporarily.
13
8
9
12
14
1
2
4
6
7
5
10
11
3

11
Chapter 1 Introduction
●Before Using Remote Control
How to install battery
1. On the back of the remote control, slide the battery
cover off in the direction of an arrow.
2. Insert a battery with the positive side up. (Battery model
number: CR2025)
3. Reattach the cover.
Receivable Range of Remote Control
Use the remote control inside of the range as below.
3m
3m
20°
20°
5m
30°
30°
7m
5m

12 Chapter 1 Introduction
1-3. Basic Operations and Functions
●Basic operation of the Setting menu
1. Displaying the Setting menu
1. Press on the remote control. The Setting menu appears.
2.
Adjusting/Setting
1. Choose a menu to adjust/set with , , and then press . The Sub menu appears.
2. Choose an item to adjust/set with , , and then press . The adjustment/setting menu
appears.
3. Adjust/set the selected item with , , , , and then press .
3.
Exiting
1. Press .
Note
• To go back to the previous menu, press .

13
Chapter 1 Introduction
●Functions
The following table shows the Setting menu and setting items of each menu.
Main menu Setting Reference
Color*1 Color Mode “2-3. Adjusting Color” (page 16)
(Regarding “Smart Functions”, see
“Chapter 4 Using Smart Function”
(page 32).)
Brightness
Black Level
Contrast
Saturation
Hue
Temperature
Advanced Settings Gamma
Gain
Noise Reduction
ContrastEnhancer
Smart Functions
Overdrive
Color Reset “3-8. Resetting the Monitor to the
Default Settings” (page 30)
Screen Color Space*2 “2-4. Setting the Color Space for the
HDMI input signal” (page 23)
Smoothing “To modify blurred characters/lines”
(page 26)
Sound Source*2 “3-1. Switching sound source for HDMI
signal input” (page 27)
Sound Level “3-3. To adjust the sound level” (page
28)
Power Save “Audio Output” (page 36)
PowerManager Power Save “5-1. Setting Power Saving” (page
35)
Monitor Settings Key Lock “3-4. Locking Operation Buttons”
(page 29)
Logo “3-5. Showing and hiding the EIZO
logo” (page 29)
Power Indicator “5-2. Setting Power Indicator” (page
37)
Language “3-6. Setting Language” (page 29)
USB Power Save “USB” (page 37)
Reset “3-8. Resetting the Monitor to the
Default Settings” (page 30)
Information “8-5. Displaying Monitor Information”
(page 52)
*1 The adjustment/settings available on the “Color” menu depend on the selected Color mode (see
“Adjustable settings in each mode” (page 17)).
*2 This function is available with HDMI signal input.

14 Chapter 2 Adjusting Screens
Chapter 2 Adjusting Screens
2-1. Compatible Resolutions/Formats
The monitor supports the following resolutions and signal format.
●DVI-D Input and HDMI Input (PC signal)
Resolution Vertical Scan Frequency
640 × 480 60 Hz
720 × 400 70 Hz
800 × 600 60 Hz
1024 × 768 60 Hz
1280 × 720 60 Hz
1280 × 960 60 Hz
1280 × 1024 60 Hz
1680 × 1050 60 Hz
1920 × 1080*1 60 Hz
*1 Recommended resolution
●HDMI Input (video signal)
• Video signal
Formats Vertical Scan Frequency
50 Hz 60 Hz
VGA -√
480p -√
480i -√
576p √-
576i √-
720p √ √
1080p √ √
1080i √ √
• Audio signal
- 2ch linear PCM (32 kHz / 44.1 kHz / 48 kHz)

15
Chapter 2 Adjusting Screens
2-2. Setting the Resolution
When you connect the monitor to the PC and nd that the resolution is improper, or when you want to
change the resolution, follow the procedure below.
Windows 8.1 / Windows 8 / Windows 7
1. For Windows 8.1 / Windows 8, click the “Desktop” tile on the Start Screen to display the desktop.
2. Right-click the mouse anywhere on the desktop except for icons.
3. From the displayed menu, click “Screen resolution”.
4. On the “Screen Resolution” dialog box, select the monitor.
5. Click “Resolution” to select the desired resolution.
6. Click the [OK] button.
7. When a conrmation dialog box is displayed, click [Keep changes].
Windows Vista
1. Right-click the mouse anywhere on the desktop except for icons.
2. From the displayed menu, click “Personalize”.
3. On the “Personalization” window, click “Display Settings”.
4. On the “Display Settings” dialog box, select the “Monitor” tab and select desired resolution in the
“Resolution” eld.
5. Click the [OK] button.
6. When a conrmation dialog box is displayed, click [Yes].
Mac OS X
1. Select “System Preferences” from the Apple menu.
2. When the “System Preferences” dialog box is displayed, click “Displays” for “Hardware”.
3. On the displayed dialog box, select the “Display” tab and select desired resolution in the
“Resolutions” eld.
4. Your selection will be reected immediately. When you are satised with the selected resolution,
close the window.

16 Chapter 2 Adjusting Screens
2-3. Adjusting Color
●To select the display mode (Color Mode)
This function allows easy selection of a desired mode according to monitor application.
Display Modes
Mode Purpose
User1 Select one of these user modes to dene a desired set of parameter settings.
User2
Game (Dark scene) Suitable for displaying games with dark images.
Game (Light scene) Suitable for displaying games with bright images.
Cinema Produces theater screen-like images. Suitable for displaying images from media such as
movies.
Web / sRGB Suitable while displaying a web browser or for color matching with sRGB compatible
peripherals.
Paper Produces a printed paper effect. Suitable for displaying images from media such as
books and documents.
Displays the current mode.
Procedure
1. Press on the remote control.
The mode name appears at the center of the screen.
2. The mode among the list is highlighted in turn each time is pressed.
You can switch the current mode with or while the mode menu is being displayed.
→User1←→User2←→Game(Darkscene)←→Game(Lightscene)←→Cinema←→Web/sRGB←→Paper←
Note
• The Setting menu and the Mode menu cannot be displayed at the same time.
• When “G-Ignition” is used, the Color Mode automatically switches to the corresponding setting for the
software being used.
(“G-Ignition” is a software that can be used to adjust the screen via mouse or keyboard. It is available for
download on our website (http://www.eizo.com).)

17
Chapter 2 Adjusting Screens
●To perform advanced adjustments
The “Color” menu of the Setting menu allows you to set and save the independent color adjustment
for each mode.
Attention
• The monitor will take about 30 minutes before its internal electric components stabilize. Wait 30 minutes or
more after turning the monitor power on before starting adjustment.
• The same image may be seen in different colors on multiple monitors due to their monitor-specic
characteristics. Make ne color adjustment visually when matching colors on multiple monitors.
Note
• You can adjust the color via mouse and keyboard by using “G-Ignition”. You can also save and load the
adjusted settings as color data.
●Adjustable settings in each mode
The adjustable settings depend on the mode. (Non-adjustable or non-settable function cannot be
selected.)
For instructions on how to adjust or set each function, refer to subsequent pages.
Regarding “Smart Functions”, see “Chapter 4 Using Smart Function” (page 32).
√: Adjustable -: Not adjustable
Function
Color Mode
User1
User2
Game
(Dark scene)
Game
(Light scene)
Cinema Web/sRGB Paper
Brightness √ √ √ √ √
Black Level √ √ √ - -
Contrast √ √ √ - -
Saturation √ √ √ - -
Hue √ √ √ - -
Temperature √ √ √ -√
Advanced Settings Gamma √ √ √ - -
Gain √- - - -
Noise Reduction √ √ - - -
ContrastEnhancer √ √ √ - -
Smart Functions Smart
Detection √ √ - - √
Smart
Resolution √ √ √ -√
Smart
Insight 2 √ √ √ - -
Overdrive √ √ √ - -
Color Reset √ √ √ √ √

18 Chapter 2 Adjusting Screens
●To adjust brightness
The screen brightness is adjusted by changing the brightness of the backlight (light source from the
LCD back panel).
Adjustable range
0 to 100
Procedure
1. Press or .
The Brightness menu appears.
2. Use or for adjustment.
3. Press to exit.
Note
• If you feel that the image is too dark even if the brightness is set to 100, adjust the contrast.
• Alternatively, you can use “Brightness” under “Color” in the Adjustment menu to adjust it.
●Adjusting the brightness and color of black “Black Level”
You can adjust the brightness and chromaticity of black by adjusting the black level of red, green, and
blue respectively. Please use a black test pattern or background for adjustment of the black level.
Adjustable range
0 to 100
Procedure
1. Choose “Color” in the Setting menu, and press .
2. Choose “Black Level” in the “Color” menu, and press .
The “Black Level” menu appears.
3. Use or for adjustment.
4. Press to exit the adjustment.
Note
• After completing black level adjustment, readjust the contrast as appropriate.
●To adjust contrast
The brightness of the screen is adjusted by varying the video signal level.
Adjustable range
0 to 100
Procedure
1. Choose “Color” in the Setting menu, and press .
2. Choose “Contrast” in the “Color” menu, and press .
The “Contrast” menu appears.
3. Use or for adjustment.
4. Press to exit the adjustment.
Note
• In the contrast of 50, every color gradation is displayed (for PC input signal only).
• When adjusting the monitor, it is recommended to perform the brightness adjustment which may not lose the
gradation characteristics, prior to the contrast adjustment.
• Perform the contrast adjustment in the following cases.
- When you feel the image is too dark even if the brightness is set to 100 (Set the contrast to higher than 50.)

19
Chapter 2 Adjusting Screens
●To adjust the color saturation
This function allows you to adjust color saturation.
Adjustable range
-50 to 50
Procedure
1. Choose “Color” in the Setting menu, and press .
2. Choose “Saturation” in the “Color” menu, and press .
The “Saturation” menu appears.
3. Use or for adjustment.
4. Press to exit the adjustment.
Attention
• Using this function may make some color gradations unavailable for display.
Note
• The minimum value (-50) changes the screen to monochrome.
●To adjust hue
This function allows you to adjust hue.
Adjustable range
-50 to 50
Procedure
1. Choose “Color” in the Setting menu, and press .
2. Choose “Hue” in the “Color” menu, and press .
The “Hue” menu appears.
3. Use or for adjustment.
4. Press to exit the adjustment.
Attention
• Using this function may make some color gradations unavailable for display.

20 Chapter 2 Adjusting Screens
●To adjust color temperature
Color temperature can be adjusted.
The color temperature is normally used to express the hue of “White” and/or “Black” by a numerical
value. The value is expressed in degrees “K” (Kelvin).
The screen becomes reddish at a low color temperature, and bluish at a high color temperature, like
the ame temperature. A gain preset value is set for each color temperature setting value.
Adjustable range
Off, 4000K-10000K (specied by every 500K unit, including 9300K)
Procedure
1. Choose “Color” in the Setting menu, and press .
2. Choose “Temperature” in the “Color” menu, and press .
The “Temperature” menu appears.
3. Use or for adjustment.
4. Press to exit the adjustment.
Note
• The value shown in “K” is available only as reference.
• “Gain” allows you to perform more advanced adjustment (see “To adjust gain” (page 21)).
• If you set to “Off”, the image is displayed in the preset color of the monitor (Gain: 100 for each RGB).
• When gain is changed, the color temperature is changed to “Off”.
●To adjust gamma
Gamma can be adjusted. The brightness of the monitor varies depending on the input signal,
however, the variation rate is not proportional to the input signal. To keep the balance between the
input signal and the brightness of the monitor is called as “Gamma correction”.
Adjustable range
1.8, 2.0, 2.2, 2.4, 2.6, 2.8, Power, RTS
Procedure
1. Choose “Color” in the Setting menu, and press .
2. Choose “Advanced Settings” in the “Color” menu, and press .
3. Choose “Gamma” in the “Advanced Settings” menu, and press .
The “Gamma” menu appears.
4. Use or for adjustment.
5. Press to exit the adjustment.
Note
• Choosing “Power” will help to sharpen halftone images by increasing their contrast.
• “RTS” is suitable for display of RTS games and brightens low gradation areas of the screen.