Eizo DURAVISION FDX1501 User manual
Important
Please read this User’s Manual and Setup Manual (separate volume)
carefully to familiarize yourself with safe and effective usage.
• Please refer to the Setup Manual for basic information ranging from
connection of the monitor to a PC to using the monitor.
• The latest User’s Manual is available for download from our web site:
http://www.eizo.com
Cover
2
Product specication may vary with sales areas. Conrm the specication in the manual written in language of the
region of purchase.
Copyright© 2011 EIZO NANAO CORPORATION All rights reserved.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means,
electronic, mechanical, or otherwise, without the prior written permission of EIZO NANAO CORPORATION.
EIZO NANAO CORPORATION is under no obligation to hold any submitted material or information condential
unless prior arrangements are made pursuant to EIZO NANAO CORPORATION’s receipt of said information.
Although every effort has been made to ensure that this manual provides up-to-date information, please note that
EIZO monitor specications are subject to change without notice.
3
Notice for this monitor
Aside from creating documents, viewing multimedia content, and other general purposes, this product is also suited to
the dedicated usages such as operation of terminal equipment.
This product has been adjusted specically for use in the region to which it was originally shipped. If the product is
used outside the region, it may not operate as specied in the specications.
This product may not be covered by warranty for uses other than those described in this manual.
The specications noted in this manual are only applicable for power cords and signal cables specied by us.
Use optional products manufactured or specied by us with this product.
As it takes about 30 minutes for the performance of electrical parts to stabilize, adjust the monitor 30 minutes or more
after the monitor power has been turned on.
In order to suppress the luminosity change by long-term use and to maintain the stable luminosity, use of a monitor in
lower brightness is recommended.
When the screen image is changed after displaying the same image for extended periods of time, an afterimage may
appear. Use the screen saver or power save function to avoid displaying the same image for extended periods of time.
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (refer to
“Cleaning” (page 4)).
The LCD panel is manufactured using high-precision technology. However, missing pixels or lit pixels may appear on
the LCD panel, this is not malfunction. Percentage of effective dots: 99.9994% or higher.
The backlight of the LCD panel has a xed life span. When the screen becomes dark or begins to icker, please contact
your dealer.
Do not scratch or press on the panel with any sharp objects, as this may result in damage to the panel. Do not attempt
to brush with tissues as this may scratch the panel.
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew condensation
may occur inside and outside the monitor. In that case, do not turn the monitor on and wait until dew condensation
disappears, otherwise it may cause some damages to the monitor.
4
Cleaning
Attention
• Never use any solvents or chemicals, such as thinner, benzene, wax, alcohol, and abrasive cleaner, which may
damage the cabinet or panel.
• Do not soak liquid into the clearance between the panel and the panel frame.
Note
• Optional ScreenCleaner is recommended for cleaning the panel surface.
● Panel
• Clean the panel with a soft cloth such as cotton cloth or lens cleaning paper.
• If necessary, stubborn stains can be removed by moistening part of a cloth with water to enhance its
cleaning power. After that, clean the panel again with a dry cloth for better nishing.
● Cabinet
• Clean the cabinet with a soft cloth dampened with a little mild detergent.
To use the monitor comfortably
• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor according
to the environmental conditions.
• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.
5
CONTENTS
CONTENTS
Cover ...................................................................... 1
Notice for this monitor ............................................ 3
CONTENTS ............................................................. 5
Chapter 1 Introduction ....................................... 6
1-1. Features ......................................................... 6
1-2. EIZO LCD Utility Disk.................................... 6
●Diskcontentsandsoftwareoverview............. 6
●Tousetouchpaneldriver............................... 6
1-3. Basic Operations and Functions ................ 7
●BasicAdjustmentmenuoperations................ 7
●Functions......................................................... 8
Chapter 2 Adjusting Screens ............................ 9
2-1. Setting the Resolution ................................. 9
●Displayresolution............................................ 9
●Settingresolution............................................ 9
Windows7................................................... 9
WindowsVista............................................. 9
WindowsXP................................................. 9
Windows2000............................................. 9
MacOSX....................................................10
2-2. Displaying Screen Correctly.......................11
●DigitalSignalInput.........................................11
●AnalogSignalInput........................................11
2-3. Adjusting Color ............................................15
●Toselectthedisplaymode
(FineContrastmode)......................................15
●Toperformadvancedadjustments................15
●Adjustablesettingsineachmode..................15
●Toadjustbrightness<Brightness>................16
●Toadjustcontrast<Contrast>........................16
●Toadjustcolortemperature<Temperature>..17
●Toadjustgain<Gain>....................................17
Chapter 3 Setting Monitor ............................... 18
3-1. Adjusting Volume “Volume” .......................18
3-2. Changing Adjustment Menu Display
Position <Menu Position> ...........................18
3-3. Locking Buttons ...........................................18
●Tolockadjustments/settingsinthe
Adjustmentmenu...........................................18
●Tolockalloperations.....................................18
3-4. Setting the EIZO Logo Display ...................19
3-5. Setting Language <Language> ..................19
3-6. Enabling/Disabling DDC/CI
communication ............................................19
3-7. Resetting the Monitor to the Default
Settings <Reset> ......................................... 20
●Toresetthecoloradjustments...................... 20
●Toresetalladjustmentstothedefault
settings.......................................................... 20
Chapter 4 Power Saving Functions ................ 21
4-1. Power Saving Mode .....................................21
4-2. Setting Power Indicator <Power
Indicator> ......................................................21
4-3. Enabling/Disabling Automatic
Brightness Adjustment “Auto EcoView” . 22
4-4. Setting Indicator “EcoView Index” ........... 22
4-5. Enabling/Disabling Auto Power-OFF
<Off Timer> .................................................. 22
Chapter 5 Troubleshooting .............................. 23
5-1. No picture .................................................... 23
5-2. Imaging problems (for both digital and
analog) .......................................................... 24
5-3. Imaging problems (for analog only) ......... 25
5-4. Other problems ........................................... 25
5-5. Touch panel problems (for FDX1501T
only) .............................................................. 26
Chapter 6 Reference ........................................ 27
6-1. How to Attach the Optional Arm ............... 27
6-2. Connecting Multiple PCs ........................... 28
●Toswitchamonginputsignals...................... 28
●Tosetinputsignalselection<InputSignal>. 29
6-3. Displaying Monitor Information
<Information> .............................................. 29
6-4. Specications ............................................. 30
6-5. Glossary ....................................................... 33
6-6. Preset Timing .............................................. 35
Appendix .............................................................. 36
Trademark ............................................................... 36
FCC Declaration of Conformity .............................37
LIMITED WARRANTY ............................................. 38
China Measures for RoHS Compliance in
ChinaRoHS ...............................................................47
6Chapter1Introduction
Chapter 1 Introduction
Thank you very much for choosing an EIZO color LCD monitor.
1-1. Features
• 15” LCD
• Applicable to the resolution of 1024 × 768.
• LED backlight LCD panel
The LED backlight provides better power efciency and reduced power consumption compared to existing uorescent
backlight LCD panels. No mercury, a hazardous substance, is used.
• High-intensity pane
Maintains visibility under high-illumination conditions
• Anti-dust design allows use in a wide range of environments.
A design without ventilation holes in the main unit makes dust penetration difcult.
• Supports a wide range of operating temperatures and operating humidity
- Operating temperature : 0°C to 50°C (32°F to 122°F)
- Operating humidity: 20% to 90% R.H. (wet bulb temperature ≤ 39 °C (102 °F), no condensation)
• A 2-year long-term warranty for 24-hour continuous use
• Resistive technology touch panel function (for FDX1501T only)
Compatible with Microsoft Windows 7 / Vista / XP / 2000
1-2. EIZO LCD Utility Disk
An “EIZO LCD Utility Disk” (CD-ROM) is supplied with this product. The following table shows the disk
contents and the overview of the software programs.
● Disk contents and software overview
The disk includes adjustment software, touch panel software, and user’s manuals. Refer to Readme.txt le on
the disk for software startup procedures or le access procedures.
Item Overview Windows Macintosh
A“Readme.txt”le √ √
Screenadjustmentpatternles Usedwhenadjustingtheimageof
analogsignalinputmanually. √ √
TouchPanelDriver*Driverfortouchpanel √ -
User’sManualofthismonitor(PDFle) √ √
User’sManualforTouchPanelDriver(PDFle)*√ -
* UsedonlyfortheFDX1501T.
● To use touch panel driver
For information on how to install or use the touch panel driver, see the Touch Panel Driver User’s Manual (on
the CD-ROM).
7
Chapter1Introduction
1-3. Basic Operations and Functions
● Basic Adjustment menu operations
1. Displaying Adjustment Menu
1. Press . The adjustment menu appears.
Atdigitalsignalinput
2.
Adjusting/Setting
1. Choose a menu to adjust/set with or , and then press . The Sub menu appears.
2. Choose an item to adjust/set with or , and then press . The adjustment/ setting menu appears.
3. Adjust/set the selected item with or , and then press .
3.
Exiting
1. Choose <Return> from the Sub menu and press . The Main menu appears.
2. Choose <Exit> from the Main menu and press . The Adjustment menu exits.
Note
• The Adjustment menu can also be exited by pressing twice quickly.
8Chapter1Introduction
● Functions
The following table shows all the Adjustment menu’s adjustment and setting menus.
Main menu Setting Reference
AutoAdjustment*1 Screen “2-2.DisplayingScreenCorrectly”
(page11)
Range
Screen Clock*1
Phase*1
Hor.Position*1
Ver.Position*1
Smoothing
Return
Color*2 Brightness “2-3.AdjustingColor”(page15)
ColorMode
Contrast
Temperature
Gain
Reset “Toresetthecoloradjustments”
(page20)
Others InputSignal “Tosetinputsignalselection<Input
Signal>”(page29)
OffTimer “4-5.Enabling/DisablingAuto
Power-OFF<OffTimer>”(page22)
MenuPosition “3-2.ChangingAdjustmentMenu
DisplayPosition<MenuPosition>”
(page18)
PowerIndicator “4-2.SettingPowerIndicator
<PowerIndicator>”(page21)
Reset “Toresetalladjustmentstothe
defaultsettings”(page20)
Information “6-3.DisplayingMonitorInformation
<Information>”(page29)
Language “3-5.SettingLanguage
<Language>”(page19)
*1Analogsignalinputonly
*2Theadjustment/settingsavailableonthe<Color>menudependontheselectedFineContrastmode.
9
Chapter2AdjustingScreens
Chapter 2 Adjusting Screens
2-1. Setting the Resolution
● Display resolution
For details on compatible resolutions, refer to “Compatible Resolutions” in the Setup Manual.
● Setting resolution
When you connect the monitor to the PC and nd that the resolution is improper, or when you want to
change the resolution, follow the procedure below.
Windows 7
1. Right-click the mouse anywhere on the desktop except for icons.
2. From the displayed menu, click “Screen resolution”.
3. On the “Screen Resolution” dialog box, select the monitor.
4. Click “Resolution” to select the desired resolution.
5. Click the “OK” button.
6. When a conrmation dialog box is displayed, click [Keep changes].
Windows Vista
1. Right-click the mouse anywhere on the desktop except for icons.
2. From the displayed menu, click “Personalize”.
3. On the “Personalization” window, click “Display Settings”.
4. On the “Display Settings” dialog box, select the “Monitor” tab and select desired resolution in the
“Resolution” eld.
5. Click the “OK” button.
6. When a conrmation dialog box is displayed, click “Yes”.
Windows XP
1. Right-click the mouse anywhere on the desktop except for icons.
2. From the displayed menu, click “Properties”.
3. When the “Display Properties” dialog box is displayed, click the “Settings” tab and select desired
resolution for “Screen resolution” under “Display”.
4. Click the “OK” button to close the dialog box.
Windows 2000
1. Right-click the mouse anywhere on the desktop except for icons.
2. From the displayed menu, click “Properties”.
3. When the “Display Properties” dialog box is displayed, click the “Settings” tab and select desired
resolution for “Screen resolution” under “Display”.
4. Click the “OK” button to close the dialog box.
10 Chapter2AdjustingScreens
Mac OS X
1. Select “System Preferences” from the Apple menu.
2. When the “System Preferences” dialog box is displayed, click “Displays” for “Hardware”.
3. On the displayed dialog box, select the “Display” tab and select desired resolution in the “Resolutions”
eld.
4. Your selection will be reected immediately. When you are satised with the selected resolution, close
the window.
11
Chapter2AdjustingScreens
2-2. Displaying Screen Correctly
● Digital Signal Input
When digital signals are input, images are displayed correctly based on the preset data of the monitor, but if
characters and/or lines appear blurred, go to “6. Modify blurred characters or lines.” (page 14).
When performing more advanced adjustment, see “2-3. Adjusting Color” (page 15) and subsequent pages.
● Analog Signal Input
Attention
• The monitor will take about 30 minutes before its internal electric components stabilize. Wait 30 minutes or more
after turning the monitor power on before starting adjustment.
• The self adjustment function does not work for the images under the vertical resolution of 480 or less.
• The self adjustment and auto adjustment functions work correctly when an image is fully displayed over the
Windows or Macintosh display area. They do not work properly in the cases below:
- When an image is displayed only on a part of the screen (command prompt window, for example)
- When a black background (wallpaper, etc.) is in use
Also, these functions cannot work properly in some graphic boards.
The monitor screen adjustment is used to suppress ickering of the screen or adjust screen position and
screen size correctly according to the PC to be used.
Note
• The self adjustment function works when all of the following conditions are satised:
- When a signal is input into the monitor for the rst time or when a resolution or vertical/horizontal scan frequency
not used before is set
If the screen is not displayed correctly even after performing the self adjustment operation, adjust the screen
according to the procedures on the following pages to use the monitor comfortably.
Setting Procedures
1. Perform the auto adjustment.
● To adjust ickering, screen position, and screen size automatically <Screen>
Procedure
1. Choose <Auto Adjustment> from the Adjustment menu, and press .
2. Choose <Screen> from the <Auto Adjustment> menu, and press .
The <Auto Adjustment> menu appears.
3. Select <Execute> with or , and press .
Flickering, screen position, and screen size are corrected by the auto-adjustment function.
Ifthescreenisnotdisplayedcorrectlyevenafterperforming“1.Performtheautoadjustment.”(page11),
performtheadjustmentsaccordingtotheproceduresonthefollowingpages.Ifthescreenisdisplayed
correctly,goto“5.Adjustingcolorgradation.”(page14).
12 Chapter2AdjustingScreens
2.
Prepare to use analog screen adjustment patterns.
Load the “EIZO LCD Utility Disk” to your PC, and then open the “Screen adjustment pattern les”.
Note
• For details and instructions on opening the “Screen adjustment pattern les”, refer to the Readme.txt le.
3.
Perform the auto adjustment again with the analog screen adjustment pattern
displayed.
● To adjust ickering, screen position, and screen size automatically <Screen>
Procedure
1. Display Pattern 1 in full screen on the monitor using the “Screen adjustment pattern les”.
2. Choose <Auto Adjustment> from the Adjustment menu, and press .
3. Choose <Screen> from the <Auto Adjustment> menu, and press .
The <Auto Adjustment> menu appears.
4. Select <Execute> with or , and press .
Flickering, screen position, and screen size are corrected by the auto-adjustment function.
Ifthescreenisnotdisplayedcorrectlyevenafterperforming“3.Performtheautoadjustmentagain
withtheanalogscreenadjustmentpatterndisplayed.”(page12),performtheadjustmentsaccordingto
theproceduresonthefollowingpages.Ifthescreenisdisplayedcorrectly,goto“5.Adjustingcolor
gradation.”(page14).
4.
Choose <Screen> from the Adjustment menu to perform advanced
adjustments.
Adjust the clock, phase and position, in this order.
● To eliminate vertical bars <Clock>
Procedure
1. Choose <Clock> from the <Screen> menu, and press .
The <Clock> menu appears.
2. Adjust the clock with or to eliminate vertical bars.
Press or slowly so as not to miss the adjustment point.
3. Press to exit the adjustment.
When blurring, ickering or bars appear on the screen after adjustment, proceed to “Phase” to remove ickering or
blurring.
13
Chapter2AdjustingScreens
● To remove ickering or blurring <Phase>
Procedure
1. Choose <Phase> from the <Screen> menu, and press .
The <Phase> menu appears.
2. Adjust the phase with or to minimize ickering or blurring.
3. Press to exit the adjustment.
When vertical bars appear on the screen after adjustment, go back to “To eliminate vertical bars <Clock>”.
(Clock → Phase → Position)
Attention
• Flickering or blurring may not be eliminated depending on your PC or graphics board.
● To correct the screen position <Hor.Position> <Ver.Position>
Note
• Since the number of pixels and the pixel positions are xed on the LCD monitor, only one position is provided to
display images correctly. The position adjustment is made to shift an image to the correct position.
Procedure
1. Choose <Hor.Position> or <Ver.Position> from the <Screen> menu, and press .
The <Hor.Position> or <Ver.Position> menu appears.
2. Adjust the position with or .
3. Press to exit the adjustment.
4. Close Pattern 1.
14 Chapter2AdjustingScreens
5.
Adjusting color gradation.
● To adjust color gradation automatically <Range>
Every color gradation (0 to 255) can be displayed by adjusting the signal output level.
Procedure
1. Display Pattern 2 in full screen on the monitor using the “Screen adjustment pattern les”.
2. Choose <Auto Adjustment> from the Adjustment menu, and press .
3. Choose <Range> from the <Auto Adjustment> menu, and press .
The <Range> menu appears.
4. Select <Execute> with or , and press .
The output range is set automatically.
5. Close Pattern 2.
6.
Modify blurred characters or lines.
● To modify blurred characters/lines <Smoothing>
When an image is displayed with a resolution other than recommended, the characters or lines of the
displayed image may blur.
Attention
• Smoothing setting may not be required depending on the display resolution. (You cannot choose the smoothing icon.)
Adjustable range
1 to 5
Procedure
1. Choose <Screen> from the Adjustment menu, and press .
2. Choose <Smoothing> from the <Screen> menu, and press .
The <Smoothing> menu appears.
3. Use or for adjustment.
4. Press to exit the adjustment.
15
Chapter2AdjustingScreens
2-3. Adjusting Color
● To select the display mode (FineContrast mode)
This function allows easy selection of a desired mode according to monitor application.
Display Modes
Mode Purpose
Custom Selectoneoftheseusermodestodeneadesiredsetofparametersettings.
EyeCare Allowsthebrightnesstobesetlowerthanpossiblewithothermodes.
sRGB SuitableforcolormatchingwithsRGBcompatibleperipherals.
Text Suitablefordisplayingtextsforwordprocessingorspreadsheets.
Procedure
1. Choose <Color> from the Adjustment menu, and press .
2. Choose <Color Mode> from the <Color> menu, and press .
3. Use or for adjustment.
4. Press to exit the adjustment.
● To perform advanced adjustments
The <Color> menu of the Adjustment menu allows you to congure and save a separate set of color settings
for each mode.
Attention
• The monitor will take about 30 minutes before its internal electric components stabilize. Wait 30 minutes or more
after turning the monitor power on before starting adjustment.
• Perform the range adjustment rst when adjusting color for analog signals (see “To adjust color gradation
automatically <Range>” (page 14)).
• The same image may be seen in different colors on multiple monitors due to their monitor-specic characteristics.
Make ne color adjustment visually when matching colors on multiple monitors.
Note
• The values shown in “%” or “K” are available only as reference.
● Adjustable settings in each mode
The adjustable settings depend on the mode. (You cannot select any non-adjustable or non-settable function.)
√: Adjustable -: Not adjustable
Icon Function FineContrast mode
Custom EyeCare sRGB Text
Brightness √√√√
Contrast √ - - √
Temperature √ √ - √
Gain √ √ - -
Reset √√√√
16 Chapter2AdjustingScreens
● To adjust brightness <Brightness>
The screen brightness is adjusted by changing the brightness of the backlight (light source from the LCD
back panel).
Adjustable range
0 to 100%
Procedure
1. Press or .
The Brightness menu appears.
2. Use or for adjustment.
3. Press to exit the adjustment.
Note
• If you feel that the image is too bright even if the brightness is set to 0% or that the image is too dark even if the
brightness is set to 100%, adjust the contrast.
• Alternatively, you can use <Brightness> under <Color> in the Adjustment menu to adjust it.
● To adjust contrast <Contrast>
The brightness of the screen is adjusted by varying the video signal level.
Adjustable range
0 to 100%
Procedure
1. Choose <Color> from the Adjustment menu, and press .
2. Choose <Contrast> from the <Color> menu, and press .
The <Contrast> menu appears.
3. Use or for adjustment.
4. Press to exit the adjustment.
Note
• In the contrast of 50%, every color gradation is displayed.
• When adjusting the monitor, it is recommended to perform the brightness adjustment which may not lose the
gradation characteristics, prior to the contrast adjustment.
• Perform the contrast adjustment in the following cases.
- When you feel the image is too dark even if the brightness is set to 100% (Set the contrast to higher than 50%.)
- When you feel the image is too bright even if the brightness is set to 0% (Set the contrast to lower than 50%.)
17
Chapter2AdjustingScreens
● To adjust color temperature <Temperature>
Color temperature can be adjusted.
The color temperature is normally used to express the hue of “White” and/or “Black” by a numerical value.
The value is expressed in degrees “K” (Kelvin).
The screen becomes reddish at a low color temperature, and bluish at a high color temperature, like the ame
temperature. A gain preset value is set for each color temperature setting value.
Adjustable range
Off, 5000K, 6500K, 9300K
Procedure
1. Choose <Color> from the Adjustment menu, and press .
2. Choose <Temperature> from the <Color> menu, and press .
The <Temperature> menu appears.
3. Use or for adjustment.
4. Press to exit the adjustment.
Note
• <Gain> allows you to perform more advanced adjustment (see “To adjust gain <Gain>” (page 17)).
• If you set to “Off”, the image is displayed in the preset color of the monitor (Gain: 100% for each RGB).
• When gain is changed, the color temperature is changed to “Off”.
● To adjust gain <Gain>
The brightness of each color component red, green, and blue is called “Gain”. You can change the hue of
“white” by adjusting gain.
Adjustable range
0 to 100%
Procedure
1. Choose <Color> from the Adjustment menu, and press .
2. Choose <Gain> from the <Color> menu, and press .
The <Gain> menu appears.
3. Adjust gain with or for each of red, green, and blue.
4. Press to exit the adjustment.
Attention
• Using this function may make some color gradations unavailable for display.
Note
• The value of gain changes with that of color temperature.
• When gain is changed, the color temperature is changed to “Off”.
18 Chapter3SettingMonitor
Chapter 3 Setting Monitor
3-1. Adjusting Volume “Volume”
This function allows you to adjust the volume.
Adjustable range
0 to 20
Procedure
1. Press .
The sound volume menu appears.
2. Use or for adjustment.
3. Press to exit the adjustment.
3-2. Changing Adjustment Menu Display Position
<Menu Position>
You can change the display position of the Adjustment menu.
Procedure
1. Choose <Others> from the Adjustment menu, and press .
2. Choose <Menu Position> from the <Others> menu, and press .
The <Menu Position> menu appears.
3. Adjust the position with or .
4. Press to exit the adjustment.
3-3. Locking Buttons
This function allows you to lock to prevent changing the adjusted/set status.
● To lock adjustments/settings in the Adjustment menu
Procedure
1. Press to turn off the monitor.
2. Press holding down to turn on the monitor.
You can toggle between Lock and Unlock by performing steps 1 and 2.
● To lock all operations
Procedure
1. Holding down, press for ve seconds while the screen is displayed.
You can toggle between Lock and Unlock by performing this step.
19
Chapter3SettingMonitor
3-4. Setting the EIZO Logo Display
You can choose to display or not to display the EIZO logo, which appears when you turn on the monitor.
Procedure
1. Press to turn off the monitor.
2. Press holding down to turn on the monitor.
The EIZO logo display setting is toggled by performing the operation in steps 1 and 2.
3-5. Setting Language <Language>
This function allows you to select a language for the Adjustment menu and messages.
Selectable languages
English / German / French / Spanish / Italian / Swedish / Simplied Chinese/ Traditional Chinese/ Japanese
Procedure
1. Choose <Language> from the Adjustment menu, and press .
The <Language> menu appears.
2. Choose a language with or .
3. Press to exit the adjustment.
3-6. Enabling/Disabling DDC/CI communication
This function allows you to enable/disable the DDC/CI communication (see “6-5. Glossary” (page 33)).
Procedure
1. Press to turn off the monitor.
2. Press holding down to turn on the monitor.
You can toggle between Enable and Disable by performing steps 1 and 2.
Note
• You can check the DDC/CI setting in the <Information> menu.
20 Chapter3SettingMonitor
3-7. Resetting the Monitor to the Default Settings
<Reset>
There are two different Resets: Color Reset for only resetting the color adjustments to the default settings and
Full Reset for resetting all settings to the defaults.
Attention
• After resetting, you cannot undo the operation.
Note
• Regarding the default setting, see “Main Default Settings” (page 32).
● To reset the color adjustments
This function only resets the color adjustments for the currently selected mode to the default settings.
Procedure
1. Choose <Color> from the Adjustment menu, and press .
2. Choose <Reset> from the <Color> menu, and press .
3. Select “Reset” with or .
4. Press .
The color adjustments revert to the default settings.
● To reset all adjustments to the default settings
This function resets all adjustments to the default settings.
Procedure
1. Choose <Others> from the Adjustment menu, and press .
2. Choose <Reset> from the <Others> menu, and press .
3. Select “Reset” with or .
4. Press .
All adjustments revert to the default settings.
Other manuals for DURAVISION FDX1501
1
This manual suits for next models
1
Table of contents
Other Eizo Monitor manuals
Eizo
Eizo RADIFORCE MS230W User manual
Eizo
Eizo FLEXSCAN S2433W User manual
Eizo
Eizo FlexScan EV2495-WT User manual
Eizo
Eizo CuratOR EX3242 User manual
Eizo
Eizo FlexScan S1932 User manual
Eizo
Eizo DuraVision FDF4627W-IP User manual
Eizo
Eizo ColorEdge CG2700X User manual
Eizo
Eizo ColorEdge CG222W User manual
Eizo
Eizo FlexScan S2242W User manual
Eizo
Eizo FLEXSCAN F930 - User manual
Eizo
Eizo FlexScan L 353T L353T-C L353T-C User manual
Eizo
Eizo FlexScan EV3240X User manual
Eizo
Eizo FlexScan T1501 User manual
Eizo
Eizo FLEXSCAN S1701-X - User manual
Eizo
Eizo FlexScan HD2442W User manual
Eizo
Eizo RadiForce MX215 User manual
Eizo
Eizo FLEXSCAN EV2315W - User manual
Eizo
Eizo DuralVision FDF2304W-IP User manual
Eizo
Eizo FlexScan L353T-C User manual
Eizo
Eizo DuraVision FCF2304W-IP User manual
