Eizo FlexScan L 461 L461 L461 User manual

ENGLISHENGLISH

2
SAFETY SYMBOLS
This manual uses the safety symbols below. They denote critical information. Please
read them carefully.
WARNING
Failure to abide by the information in a WARNING may result in serious
injury and can be life threatening.
CAUTION
Failure to abide by the information in a CAUTION may result in moderate
injury and/or property or product damage.
Indicates a prohibited action.
Indicates to ground for safety.
Copyright© 2001 by EIZO NANAO CORPORATION. All rights reserved. No part of
this manual may be reproduced, stored in a retrieval system, or transmitted, in any form
or by any means, electronic, mechanical, or otherwise, without the prior written
permissionofEizoNanaoCorporation.
Eizo Nanao Corporation is under no obligation to hold any submitted material or
information confidential unless prior arrangements are made pursuant to Eizo Nanao
Corporation's receipt of said information. Although every effort has been made to ensure
thatthismanualprovidesup-to-dateinformation,please note that EIZO monitor
specifications are subject to change without notice.
ENERGY STAR is a U.S.registered mark.
AppleandMacintoshareregisteredtrademarks of Apple Computer, Inc.
VGA is a registered trademark of International Business Machines Corporation.
DPMS is a trademark andVESA is a registered trademark ofVideo Electronics
StandardsAssociation.
Windowsisaregisteredtrademarkof Microsoft Corporation.
ScreenManagerand PowerManageraretrademarks ofEizoNanao Corporation.
FlexScanandEIZOareregistered trademarks of Eizo Nanao Corporation.
AsanENERGYSTAR® Partner, Eizo NanaoCorporationhas determined that
this product meets the ENERGY STAR guidelines for energy efficiency.

TABLEOFCONTENTS 3
ENGLISH
TABLE OF CONTENTS
PRECAUTIONS .............................................................................. 4
1. INTRODUCTION............................................................................ 9
1-1. Features ....................................................................................................... 9
1-2. Package Contents ........................................................................................ 9
1-3. Controls&Connectors................................................................................ 10
2. CABLE CONNECTION................................................................ 11
2-1. Beforeconnecting....................................................................................... 11
2-2. Connectingthesignalcable ........................................................................ 12
3. ScreenManager........................................................................... 14
3-1. Howtouse the ScreenManager .................................................................. 14
3-2. ScreenManager Adjustments and Settings ............................................... 15
3-3. UsefulFunctions......................................................................................... 16
4. ADJUSTMENT ............................................................................ 18
4-1. ScreenAdjustment ..................................................................................... 18
4-2. Displayingthelowresolutions..................................................................... 22
4-3. Coloradjustment......................................................................................... 24
4-4. Power-saveSetup....................................................................................... 26
5. ATTACHING AN ARM STAND .................................................... 27
6. TROUBLE SHOOTING ................................................................ 29
7. CLEANING................................................................................... 32
8. SPECIFICATIONS ....................................................................... 33
9. GLOSSARY.................................................................................. 35
10. INDEX .......................................................................................... 37
APPENDIX............................................................................................. i

4PRECAUTIONS
PRECAUTIONS
´ If the unit begins to emit smoke, smells like something is burning, or
makes strange noises, disconnect all power connections immediately and
contact your dealer for advice.
Attempting to use a malfunctioning unit can be dangerous.
´ Do not dismantle the cabinet or modify the unit.
Dismantling the cabinet or modifying the unit may result in electric shock or
burn.
´ Refer all servicing to qualified service personnel.
Do not attempt to service this product yourself as opening or removing covers
may expose you to dangerous voltage or other hazards.
IMPORTANT!
´ This product has been adjusted specifically for use in the region to which it was
originally shipped. If operated outside the region to which it was originally shipped,
the product may not perform as stated in the specifications.
´ To ensure personal safety and proper maintenance. Please read this section and the
caution statements on the unit (refer to the figure below).
[Locationof the Caution Statements]
WARNING
Theequipment mustbeconnected toagroundedmain outlet.
Jordetstikkontakt skal benyttes nårapparatet tilkobles
datanett.
Apparatenskall anslutas tilljordatnätuttag.
CAUTION:Risk of electric shock. Do not open.
ATTENTION:Risquedechocelectrique.Nepas ouvrir.
ACHTUNG:Gefahrdes elektrischenschlages.Rückwandnichtentfernen.

PRECAUTIONS 5
ENGLISH
• Keep small objects or liquids away from the unit.
Small objects accidentally falling through the ventilation slots into the cabinet
or spillage into the cabinet may result in fire, electric shock, or equipment
damage. If an object or liquid falls/spills into the cabinet, unplug the unit
immediately. Have the unit checked by a qualified service engineer before
using it again.
´ Place the unit on a strong, stable surface.
A unit placed on an inadequate surface may fall, resulting in injury or equipment
damage. If the unit falls, disconnect the power immediately and have the unit
checked by a qualified service engineer before using it again. Using a unit after
it has been dropped may result in fire or electric shock.
´ Set the unit in an appropriate location.
Not doing so may cause damage and could result in fire or electric shock.
* Donotplaceinoutdoors.
* Do not place in the transportation system (ship, aircraft, trains, automobiles,
etc.)
* Do not install in a dusty or humid environment.
* Do not place in a location where steam can have direct contact with the
screen.
* Donotplacenearheatgeneratingdevicesor a humidifier.
• To avoid danger of suffocation,keep the plastic packing bags away
from babies and children.
• Use the enclosed power cord and connect to the standard power outlet of
your country. Be sure to remain within the rated voltage of the power
cord.
Not doing so may cause in fire or electric shock.
´ To disconnect the power cord,grasp the plug firmly and pull.
Never tug on the cord, doing so may cause damage and could result in fire or
electric shock.
´ The equipment must be connected to a grounded main outlet.
Not doing so may cause in fire or electric shock.
OK
WARNING
OK

6PRECAUTIONS
´ Use the correct voltage.
* The unit is designed for use with a specific voltage only. Connection to
another voltage than specified in this User’s Manual may cause fire, electric
shock,orother damage.
* Do not overload your power circuit, as this may result in fire or electric
shock.
* For proper connections of the power cord, be certain to plug the power cord
to the provided unit connector and directly to a wall outlet. Not doing so may
result in fire or electric shock.
´ Handle the power cord with care.
* Do not place the cord underneath the unit or other heavy objects.
* Do not pull on or tie the cord.
If the power cord becomes damaged, stop using it. Use of a damaged cord
may result in fire or electric shock.
´ Never touch the plug and power cord if it begins to thunder.
Touching them may result in electric shock.
´ When attaching an arm stand,please refer to the user’s manual of the arm
stand and install the unit securely with the enclosed screws.
Not doing so may cause the unit to come unattached, which may result in
injury or equipment damage. Whenthe unit is dropped, please ask your dealer
for advice. Do not continue using a damaged unit. Using a damaged unit may
result in fire or electric shock.When reattaching the tilt stand, please use the
same screws and tighten them securely.
´ Do not touch a damaged LCD panel directly with bare hands.
The liquid crystal which leaks from the panel is poisonous if it enters the eyes
or mouth. If any part of the skin or body comes in direct contact with the
panel, please wash thoroughly. If some physical symptoms result, please
consult your doctor.
´ Follow local regulation or laws for safe disposal.
The backlight of the LCD panel contains mercury.
WARNING

PRECAUTIONS 7
ENGLISH
´ Handle with care when carrying the unit.
Disconnect the power cord and cables when moving the unit. Moving the unit
with the cord attached is dangerous. It may result in injury or equipment
damage.
* When handling the unit, grip the bottom of the unit firmly with both hands
ensuring the panel faces outward before lifting.
Droppingtheunitmayresultininjuryorequipmentdamage.
´ Do not block the ventilation slots on the cabinet.
* Do not place books or any other papers on the ventilation slots.
* Do not install the unit in a closed space.
* Do not use the unit laying down or upside down.
Using the unit in these ways blocks the ventilation slots and prevents proper
airflow, leading to fire or other damage.
´ Do not touch the plug with wet hands.
Touching the plug with wet hands is dangerous and can cause electrical shock.
´ Use an easily accessible power outlet.
This will ensure that you can disconnect the power quickly in case of a
problem.
´ Periodically clean the area around the plug.
Buildup of dust, water, or oil on the plug may result in fire.
´ Unplug the unit before cleaning it.
Cleaning the unit while it is plugged into a power outlet may result in electric
shock.
´ If you plan to leave the unit unused for an extended period, disconnect the
power cord from the wall socket after turning off the power switch for the
safety and the power conservation.
OK
WARNING
CAUTION

8PRECAUTIONS
Suggestions for Maximizing Comfort
´To lessen the chance of possible injury and to increase your comfort and
productivity while you operate the unit, we suggest the followings:
* Avoid less favorable body positioning. Sit back on the chair with
your back straight.
* Adjust the height of the chair so that the both soles touch the floor.
* Adjust the height of your chair, unit, or keyboard so that you
can keep your wrists straight while typing.
* Set the unit slightly below eye level.
´Adjust brightness of the screen depending on the brightness of your
environment. Too dark or too bright of a screen can cause eyestrain.
´Be sure to take adequate rests. A 10-minute rest period each hour is
suggested.
LCD Panel
´The screen may have defective pixels. These pixels may appear as
slightly light or dark area on the screen. This is due to the characteristics
of the panel itself, and not the product.
´The backlight of the LCD panel has a fixed life span.
When the screen becomes dark or begins to flicker, please contact your
dealer.
´Do not press on the panel or edge of the frame strongly, as this will result
in damage to the screen. There will be prints left on the screen if the
pressed image is dark or black. If pressure is repeatedly applied to the
screen,itmaydeteriorateordamageyourLCDpanel.Leavethescreen
whitetodecreasetheprints.
´Do not scratch or press on the panel with any sharp objects, such as a
pencil or pen as this may result in damage to the panel. Do not attempt to
brush with tissues as this may scratch the LCD panel.

ENGLISH
1.INTRODUCTION 9
1. INTRODUCTION
Thank you very much for choosing an EIZO Color Monitor.
1-1. Features
•1280x1024resolutionp.36) incorporated 16 inch Color LCD Monitor
•DVI p.35) digital input (TMDS p.36)) compliant
•Horizontal scanning frequency of 31.5 ~ 80kHz
Horizontal (Digital): 31.5 ~ 64 kHz
Vertical scanning frequency of 50 ~ 85 Hz (1280 x 1024 ~ 75Hz)
Vertical (Digital): 60 Hz (VGA Text: 70 Hz)
•AutoAdjustmentcompliantandoriginal “Picture Adjustment Program”software
included
•ColorManagementfunction incorporated
1-2. Package Contents
Please contact your local dealer for assistance if any of the listed items are missing or
damaged.
•LCDMonitor •PowerCord
•SignalCable(FD-C16) •4 of M4 x 16 mm mounting screws
•EIZO LCD Utility Disk •User’sManual
•QuickReference •LimitedWarranty
•Pleaseretain the packing materials for futuretransference.

10 1.INTRODUCTION
1-3. Controls & Connectors
Front
(1) ScreenManager™
(2) AUTOAdjustmentbutton
(3) ControlButtons
(4) EnterButton
(5) PowerSwitch
(6) PowerIndicator*1
Indicatedcolor Monitor’s status
Green Power -on
Yellow Powersavemode
FlashingYellow Powersavemode
(2 times for each) fordigital
Slowly flashingYellow Power is off
Rear (7) PowerConnector
(8) Security Lock Slot*2
(9) DVI-I Input Connector
(10) 4 Holes for Mounting an Arm-Stand*3
(11) Stand(Detatchable)*3
(7) (9)
(10)
(11)
(8)
*1 Regarding the power indicator for the “Off Timer”, see page 17.
*2 Allows for connection of a security cable. This lock supports Kensington’s MicroSaver
security system. For further information, please consult:
Kensington Technology Group 2855 Campus Drive, San Mateo, CA 94403 USA
800-650-4242,x3348
Intl: 650-572-2700,x3348 / Fax: [phone]
http://www.kensington.com
*3 The L461 can be used with an optional arm stand by removing the original stand
(see page 27).
(1)
(2)(3)(4)(5)(6)

2.CABLE CONNECTION 11
ENGLISH
2. CABLE CONNECTION
2-1. Before connecting
Before connecting your monitor to the PC, change the display screen settings (resolution
and frequency) in accordance with the charts below.
Analog Input
•About Plug & Play of the monitor
When your computer and display supportVESA DDC, the suitable resolution
and the refresh rate are set by just plugging your display into the computer without
any manual settings. When your computer system supports Plug & Play, the
Display Information File is not required except for installing the Color Profile.
Digital Input
Only the following resolutions with frequency can be displayed on this model.
noituloseR ycneuqerF skrameR
084x046zH06AGV
004x027zH07txeTAGV
006x008zH06ASEV
867x4201zH06ASEV
069x0821zH06ASEV
4201x0821zH06ASEV
noituloseR ycneuqerF skrameR
084x046zH58~ASEV,AGV
084x046zH76.66hsotnicaMelppA
004x027zH07txeTAGV
006x008zH58~ASEV
426x238zH57hsotnicaMelppA
867x4201zH58~ASEV
468x2511zH57ASEV
078x2511zH57hsotnicaMelppA
069x0821zH57hsotnicaMelppA
4201x0821zH57~ASEV

12 2.CABLE CONNECTION
2-2. Connecting the signal cable
•Be sure that the power switches of both the PC and the monitor are OFF.
1. Plug the signal cable into the DVI-I connector at the rear of the
monitor and the other end of the cable into the video connector on the
PC.
Afterconnecting,securetheconnectionwiththescrew-in fasteners.
FD-C16(enclosed)
MacintoshAdapter (Optional)
VideoOutput Connector
D-Submini15pin
VideoOutput Connector
D-Sub15 pin
FD-C04(Optional)
VideoOutput Connector
DVI
[Analog Input]
[Digital Input]
•The L461 is not compatible with a Power Macintosh G4/G4 Cube ADC (Apple
DisplayConnector).
·Standardgraphicsboard
·Macintosh G3 (Blue &White) / G4
Macintosh
Digitalgraphics board

2.CABLE CONNECTION 13
ENGLISH
2. Plug the power cord into the power connector on the rear of the
monitor and plug the other end of the power cord into a power outlet.
•Use the enclosed power cord and connect to the standard
power outlet of your country. Be sure to remain within the
rated voltage of the power cord.
Not doing so may cause in fire or electric shock.
•The equipment must be connected to a grounded main
outlet.
Not doing so may cause in fire or electric shock.
WARNING
WARNING
3. Turn on the monitor’s power and then switch on the PC’s power.
Whenever finished, turn off the PC and the monitor.

14 3.ScreenManager
3. ScreenManager
3-1. How to use the ScreenManager
As shown on the display, the ScreenManager is used to adjust the LCD monitor.
ScreenManager consists of main menus and sub menus. Adjustments are made using the
Enter and Control buttons (up, down, right and left) located on the front panel.
1. Entering the ScreenManager
Push the Enter Button once to display the main menu of the ScreenManager.
2. Making Adjustments and Settings
(1) Select the desired sub menu icon using the Control buttons and push the Enter
button. The sub menu appears.
(2) Use the Control buttons to select the desired setting icon and push the Enter
button. The setting menu appears.
(3) Use the Control buttons to make all required adjustments and push the Enter
button to save the settings.
3. Exiting the ScreenManager
(1) To return to the main menu, select the “Return”icon or push the down button
twice,followed by the Enter button.
(2) To exit the ScreenManager, select “Exit”icon and push the Enter button.
•Double clicking the Enter button at any time also exits the ScreenManager menu.
EnterButton
ControlButtons
Auto Adjustment Button
[ Main Menu ]

3.ScreenManager 15
ENGLISH
3-2. ScreenManager Adjustments and Settings.
The following table shows all the ScreenManager’s adjustment and setting menus.
“*”indicates adjustments of analog input only and “**”indicates digital input only.
Main menu Sub menu Reference
Screen Clock*
Phase*
Position*
Resolution*
Smoothing
Contrast/Brightness
Color- RangeAdjustment*
Management StandardMode Temperature
CustomMode Temperature
Saturation
Hue
Gain
Save
PowerManager DVI DMPM**
VESA DPMS*
Others Screen Size
BorderIntensity
OffTimer Set the monitor’s off timer to
onoroff.(p.17)
MenuPosition Adjust the menu position.
MenuOffTimer Set the menu displaying time.
Translucent Set the transparency of the
whitebackgroundforthe menu.
Reset Return to the factory default
settings. (p.34)
Information Information Reviewthe ScreenManager’s
settings, model name, Serial
Numberandusage time*1.
Language SelecttheScreenManager’s
language.
4.ADJUSTMENT(p.18)
English,German,French, Spanish,
Italian,SwedishandJapanese
*1 Due to the inspection on the factory, the usage time may not “0 hour”at shipping.

16 3.ScreenManager
3-3. Useful Functions
Adjustment Lock
Use the “Adjustment Lock”function to prevent any accidental changes.
Lockedfunction •Auto adjustment button adjustments and settings in the
ScreenManager.
Unlockedfunction •Adjustment of contrast and brightness by the control buttons.
•To lock
Presson the Auto adjustment button while switching on the monitor’spower switch
on the front panel.
•To unlock
Switch off the monitor’s power by the power switch on the front panel, then hold
down the Auto adjustment button once again and turn the power back on.
EIZO Logo Disappearing function
When switching on the power, the EIZO logo is displayed for a while. If you desire to
undisplay this logo, use this function.
•To undisplay
Switch off the monitor’s power by the power switch on the front panel. Turn the
power back again with pressing the enter button on the front panel.
•To display again
Switch off the monitor’s power by the power switch on the front panel. Turn the
power back again with pressing the enter button on the front panel.

3.ScreenManager 17
ENGLISH
CP rotinoM DEL
)H32~H1(doirePnOnoitarepOneerG
"doirepnO"ni.nim51tsaLecitoNecnavdA
1*
gnihsalFneerG
deripxe"doirepnO"edoM"ffOrewoP"ylwolswolleygnihsalF
Off Timer
The off timer function causes the monitor to automatically enter a power off mode after a
predetermined amount of time has lapsed. This function was created to reduce
afterimage p.35) characteristics that are particular to LCD monitors when the monitor
screen is left on for a long period without use.
[Procedure]
(1) Select “Off Timer”in the ScreenManager “Others”menu.
(2) Select “Enable”and press the right and left buttons to adjust the “On Period”
(1to23hours).
[Off timer system]
*1Advance notice (LED flashing green) will be given 15 minutes before the monitor
automatically enters the “Power Off”mode. To delay entering the “Power Off”mode,
press the power switch during the advance notice period. The monitor will continue to
operate for an additional 90 minutes.
Press the power switch to return to a normal screen.
•The off timer function works while the PowerManager is active, but there is no
advance notice before the monitor’s power is switched off.

18 4.ADJUSTMENT
4. ADJUSTMENT
4-1. Screen Adjustment
•Allow the LCD monitor to stabilize for at least 20 minutes before making image
adjustments.
Screen adjustments for the LCD monitor should be used in suppressing screen flickering
and also for adjusting the screen to its proper position. There is only one correct position
for each display mode. When using the analog input, it is also recommended to use the
ScreenManager function when first installing the display or whenever changing the
system. For convenience, an easy set-up Program installed on the utility disk to assist in
theset-upprocedureisprovided.
When using the digital input, the monitor displays the digital input image correctly based
on its pre-setting data. Please adjust the contrast and brightness as desired with referring
page 21.
1. Push the Auto adjustment button on the front panel.
The message “Your setting will be lost, if you press again now.”appears and
remains on the screen for 5 seconds. While the message is on the screen, push the
Auto adjustment button again to automatically adjust the clock, phase, screen
position and resolution. If you do not wish to do adjust the screen, do not push the
Autoadjustmentbutton again.
If the appropriate screen can not be made by using the Auto adjustment button,
adjustthescreenthroughthefollowingprocedures.
2. Install the “Screen adjustment program”.
Having read the “readme.txt”file, install and run the “Screen adjustment program”
in the enclosed EIZO LCD utility disk.
Step by step adjustment is provided by the wizard guide.
•If the user’s operating system has no utility disk (e.g.OS/2), we recommend
setting the desktop pattern to that as shown in the diagram below.
Every-other-dot
pattern

4.ADJUSTMENT 19
ENGLISH
3. Adjust by using “Screen”menu in the ScreenManager.
(1) Vertical bars appear on the screen.
ÆÆ
ÆÆ
ÆUse the “Clock”p.35) adjustment
Select the “Clock”and eliminate the vertical bars by using the right and left of
thecontrolbuttons. Donotcontinuouslypressthecontrolbuttons,asthe
adjustment value will change quickly and make it difficult to locate the most
suitableadjustmentpoint.
If the horizontal flickering, blur or bars appear, proceed to “Phase”adjustment
as follows.
•When adjusting the “Clock,”the horizontal screen size will also change.
(2) Horizontal flickering, blurring or bars appear on the screen.
ÆÆ
ÆÆ
ÆUse the “Phase”p.36) adjustment.
Select the “Phase”and eliminate the horizontal flickering, blurring or bars by
using the right and left buttons.
•Horizontal bars may not completely disappear from the screen depending on the
PC.

20 4.ADJUSTMENT
(3) The screen position is incorrect.
ÆÆ
ÆÆ
ÆUse the “Position”adjustment.
The correct displayed position of LCD monitor is decided because the number
and the position of the pixels are fixed. The “Position”adjustment moves the
image to the correct position.
Select “Position”and adjust the position so all the dotted line appear around
screen, by using the up, down, right and left buttons.
(4) Screen image is smaller or larger than the actual screen images.
ÆÆ
ÆÆ
ÆUse the “Resolution”adjustment.
Adjustment is needed when the input signal resolution and the resolution now
being displayed is different.
Select “Resolution”and confirm if the resolution now being displayed is the
same as the input resolution. If it is not, adjust the vertical resolution using
the up and down button and adjust the horizontal resolution using the right
andleftbuttons.
Adjusted to actual screen
Smaller than the actual screen images.
Larger than the actual screen images.