Eizo CH5 User manual

1
Thank you very much for choosing an EIZO product.
Please read this User’s Manual carefully to familiarize you with safe and effective usage procedures.
Please retain this manual for future reference.
PRECAUTIONS
To ensure personal safety and proper maintenance, please read this section.
CAUTION
Do not carry the monitor with the hood attached.
While carrying the monitor, the hood may fall or slip off, which may result in injury or
equipment damage.
Do not place any objects on the hood.
If the hood falls or slips off or the monitor falls over, it may result in injury or equipment
damage.
Attach only to specied EIZO LCD monitors.
Attach only to specied EIZO LCD monitors. Attaching to other monitors may cause the
hood to drop, which may result in injury or equipment damage. For the specied monitors,
please visit our website at http://www.eizo.com.
The monitor hood assembling procedure is available from our video site.
[Video site’s URL] [QR code]
http://www.eizo.com/i/hood/
English
<Landscape> <Portrait>

2
Package Contents
Please contact your local EIZO representative for assistance if any of the listed items are missing or damaged.
Hood components (8 pcs.)
Plate (1)
Plate (2)
Plate (3)
Plate (4)
Plate (5)
Plate (6)
Metal tting (7)
Cover (8)
* Plate (3) and plate (6) are not used in the landscape position.
*
User’s Manual (this manual)

3
Installation (Landscape)
To use the monitor in the portrait position, go to page 6.
1.
Assemble the left and right hoods.
1. Place plate(2) on a at surface such as a desk. Set up plate(1) at a right angle, and snap the tab until it
clicks (2 positions).
* It is recommended that the tabs are snapped separately.
Before attachment
Snap the tab so that and
are connected.
Plate (1)
Plate (2)
After attachment
2. Assemble plate(4) and (5) in the same way.
Detachment
Fold the hood at the connecting part.
English

4
2.
Attach the left and right hoods to the monitor.
1. Face the back side of the monitor toward the front.
Monitor hole
2. Align the hooks on the hood with the corresponding holes in the monitor, and then insert the hooks.
Hook
3. While holding the monitor from the bottom, press down the hood to x it rmly.
4. Attach the hood on the other side in the same way.
Hole

5
3.
Attach metal tting (7).
Holes on top (monitor top view) Insert the front hook of metal
tting (7) into the hole on top.
While pulling metal tting (7)
forward, insert the back hook of
metal tting (7) into the hole on
top.
4.
Attach cover (8).
Hook cover (8) on the top of the
hood.
Place cover (8) on the top of the
hood while aligning the catch on
cover (8) with the notch on top.
Slide cover (8) to the right to close
the hood.
Sensor Attachment
When performing calibration, slide cover (8) to the
right in order to attach the sensor.
English

6
Installation (Portrait)
1.
Assemble the left and right hoods.
1. Place plate(2) on a at surface such as a desk. Set up plate(1) at a right angle, and snap the tab until it
clicks (2 positions).
* It is recommended that the tabs are snapped separately.
Plate (1)
Plate (2)
Before attachment
Snap the tab so that and
are connected.
After attachment
2. Assemble plate(4) and (5) in the same way.
3. Place connected plate(1) and (2) on a at surface such as a desk. Set up plate(3) at a right angle, and snap
the tab until it clicks (2 positions).
After attachment
Snap the tab so that
and are connected.
Plate (3)
Plate (1)
Plate (2)
4. Assemble plate(6) to connected plate(4) and (5) in the same way.

7
Detachment
Fold the hood at the connecting part.
2.
Attach the left and right hoods to the monitor.
1. Face the back side of the monitor toward the front.
Monitor hole
2. Align the hooks on the hood with the corresponding holes in the monitor, and then insert the hooks.
Hook Hole
English

8
3. While holding the monitor from the bottom, press down the hood to x it rmly.
4. Attach the hood on the other side in the same way.
3.
Attach metal tting (7).
Use the procedure on page 5 for reference.
4.
Attach cover (8).
Use the procedure on page 5 for reference.
Sensor Attachment
When performing calibration, remove cover (8) and
then attach the sensor.

1
Specications / 仕様
● CH5
Dimensions
(W) x (H) x (D)
Landscape 653mm (25.7) × 373 mm (14.7) x 225.5 mm (8.9)
Portrait 410.5mm (16.2) × 635.5mm (25.0) x 225.5mm (8.9)
Weight Landscape Approx. 940g (2.07 lbs)
Portrait Approx. 1180g (2.6 lbs)
寸法
（幅）×（高さ）×（奥行き）
横置き 653mm×373mm×225.5mm
縦置き 410.5mm×635.5mm× 225.5mm
質量 横置き 約940g
縦置き 約1180g
Dimensions/外形寸法
410.5 (16.2)
225.5 (8.9)
635.5 (25.0)
264.5 (10.4)
109.4 (4.3)
(4.6)(0.18)
653 (25.7)
(4.6)(0.18)
264.5 (10.4) 225.5 (8.9)
373 (14.7)
109.4 (4.3)
Unit: mm (inch)
単位：mm(インチ）
Landscape/横置き
Portrait/縦置き
Spec/ 仕様

2
● CH6
Dimensions
(W) x (H) x (D)
Landscape 552mm (21.7) × 373 mm (14.7) x 225.5 mm (8.9)
Portrait 361 mm (14.2) × 555 mm (21.9) x 225.5 mm (8.9)
Weight Landscape Approx. 840g (1.85 lbs)
Portrait Approx. 960g (2.12 lbs)
寸法
（幅）×（高さ）×（奥行き）
横置き 552mm×373mm×225.5mm
縦置き 361mm×555mm× 225.5mm
質量 横置き 約840g
縦置き 約960g
Dimensions/外形寸法
Unit: mm (inch)
単位：mm(インチ）
264.5 (10.4)
552 (21.7)
4.6 (0.18)
373 (14.7)
225.5 (8.9)
109.4 (4.3)
109.4 (4.3)
555 (21.9)
225.5 (8.9)
264.5 (10.4)
361 (14.2)
4.6 (0.18)
Landscape/横置き
Portrait/縦置き